Posted: Tue Apr 12, 2022 18:00 Post subject: New Build - 04/12/2022 - r48646
Welcome to Broadcom r48646 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• DNScrypt 1.95 can still be used in WebUIbut v2 (not compatible) requires Golang and thus Entware. See Trac ticket #6246.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try client or repeater modes, but YMMV.
• VAPs not working at bootare fixed, both unbridged (r40634) and bridged (r47822). Please test, removestartup commands.
• If startup scripts do not work from USB add delay (wait script), sleep 25 or try Administration -> Commands -> Save USB.
• Broadcom ARM devices if 5 GHz channels are missingvia Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r48646 std (04/12/22) Kernel: Linux 4.4.302 #5712 SMP Tue Apr 12 04:34:21 +07 2022 armv7l Mode: Gateway, Wireless AP, Static Leases. CTF & FA Enabled. NAT and QOS Off. All services off under Status>Sys-info. Reset: Nope. Previous: 04-08-2022-r48607 Status: Working so far, still testing. Temperatures: CPU 56.9 °C / WL0 50.1 °C / WL1 51.7 °C Base CFE: Modified Asus ASUS RT-AC68P/ASUS RT-AC68U (C0 Model CFE V1.3.0.7) Configured as a stock R7000.
Speedtest-3.jpg
Description:
Speedtest Over 5.8GHz Wireless.
Filesize:
58.1 KB
Viewed:
5535 Time(s)
Logs.txt
Description:
Full system logs. MAC scrubbed, password scrubbed, the fun stuff at the bottom as usual!
Router/Version: DD-WRT v3.0-r48646 mini (04/12/22)
File/Kernel: trendnet-811dru-webflash.bin / Linux 4.4.302 #5715 Tue Apr 12 14:48:09 +07 2022 armv7l
Previous/Reset: DD-WRT v3.0-r48607 mini (04/08/22)/no
Mode/Status: Client AP/ Booted clean, CPU 84.1 °C / WL0 58.0 °C / WL1 62.2 °C
Issues/Errors: temps a bit higher than prev but ok, UI ok, thx devs - so far so good
update: stable after 3 days 9hrs uptime
CPU 83.6 °C / WL0 56.7 °C / WL1 61.8 °C
seems solid
Last edited by angler on Sat Apr 16, 2022 16:17; edited 1 time in total
Joined: 18 Mar 2014 Posts: 12922 Location: Netherlands
Posted: Wed Apr 13, 2022 7:49 Post subject:
Router Model: Netgear R6400v2, board_id: U12H332T
Firmware Version: DD-WRT v3.0-r48647M Community Build (04/13/22)
Kernel Version: Linux 4.4.302 #1 SMP Wed Apr 13 08:14:42 CEST 2022 armv7l
Upgraded from: DD-WRT v3.0-r48607M Community Build (04/07/22)
Reset: No not this time
Status: Up and running for 2 hours, basic setup as Gateway, static leases, 2,4GHz and 5Ghz working, USB storage NAS working.
OpenVPN server working.
WireGuard server working with 8 clients (phones, Windows and two other routers for site-to-site setup).
mDNS/Avahi working.
Issues/Errors: My one wireless WPA device reports on Sys-info page that ‘Signal Quality’ is ‘100%’. I expect ~70%. I have tested in Edge & Chrome, but no difference. This issue has been present for the last 3 releases (at least).
Assumptions:
1. Everyone on the forum has read the relevant forum section announcements.
2. For Broadcom section we have ALL at least tried to understand the "Peacock" thread,HERE
Everything seems to be working.
I started from scratch in an effort to get VLANs and VAPs working. See my posts in previous thread for more details.
The final break through was realizing I needed to explicitly assign Port 0 to VLAN1 in my startup script. But to recap:
I needed to set up the port assignment so that the trunk port back to my router was tagged on the new VLANs but untagged on VLAN1. I wanted to use the WAN (port 0) for this. This cannot be done with the GUI.
I wanted 3 additional VLANs bridged with 3 VAPs (2 on the 2.4GHz band and one 5GHz).
I set up the VAPs using the GUI. I created the bridges using the GUI and added each VAP to a separate bridge. (See attachment for Networking Tab for settings).
I created the VLANs and their assignment to the bridges using the following script:
Code:
swconfig dev switch0 set reset 1
swconfig dev switch0 set enable_vlan 1
swconfig dev switch0 vlan 1 set ports "0 1 2 3 4 5t"
swconfig dev switch0 vlan 3 set ports "0t 5t"
swconfig dev switch0 vlan 5 set ports "0t 5t"
swconfig dev switch0 vlan 100 set ports "0t 5t"
vconfig set_name_type VLAN_PLUS_VID_NO_PAD
swconfig dev switch0 set apply
vconfig add eth0 3
ifconfig vlan3 up
brctl addif br3 vlan3
ifconfig br3 192.168.3.254 netmask 255.255.255.0
vconfig add eth0 5
ifconfig vlan5 up
brctl addif br5 vlan5
ifconfig br5 192.168.5.254 netmask 255.255.255.0
vconfig add eth0 100
ifconfig vlan100 up
brctl addif br2 vlan100
ifconfig br2 192.168.100.254 netmask 255.255.255.0swconfig dev switch0 set reset 1
swconfig dev switch0 set enable_vlan 1
swconfig dev switch0 vlan 1 set ports "0 1 2 3 4 5t"
swconfig dev switch0 vlan 3 set ports "0t 5t"
swconfig dev switch0 vlan 5 set ports "0t 5t"
swconfig dev switch0 vlan 100 set ports "0t 5t"
vconfig set_name_type VLAN_PLUS_VID_NO_PAD
swconfig dev switch0 set apply
vconfig add eth0 3
ifconfig vlan3 up
brctl addif br3 vlan3
ifconfig br3 192.168.3.254 netmask 255.255.255.0
vconfig add eth0 5
ifconfig vlan5 up
brctl addif br5 vlan5
ifconfig br5 192.168.5.254 netmask 255.255.255.0
vconfig add eth0 100
ifconfig vlan100 up
brctl addif br2 vlan100
ifconfig br2 192.168.100.254 netmask 255.255.255.0
Rebooted the router and everything works.
Initially the VAPs worked but I then had no Internet access on any of the LAN ports - that's when I realized I should try adding port 0 to VLAN1. I'd tried doing this via the GUI on an earlier release but couldn't get it to stay that way.
I didn't change anything on the Switch Config Tab and that still shows VLAN1 with ports 1 - 4 and VLAN2 with port 0 !!
Anyhow, it appears to be working. Thanks to @egc, @blkt and @the-joker for support. Thanks also to BS and other developers.
Will report back if I have any further issues.
Mike
Screenshot 2022-04-14 114312.jpg
Description:
Network tab showing bridge config and vlan assignment post startup
Firmware: v3.0-r48646 std (04/12/22)
Router/Version: Netgear R7000 Kernel: Linux 4.4.302 #5712 SMP Tue Apr 12 04:34:21 +07 2022 armv7l
Previous: v3.0-r48607 std (04/08/22)
Mode/Status: AP wired and wireless / Up and running for 43 hours
Reset: Soft boot before and after upgrade
Temperatures: CPU 60.2 °C / WL0 46.0 °C / WL1 51.0 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
Upload and Download speeds are to ISP spec (500/500 Mbps).
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- Shortcut Forwarding Engine: CTF, Flow Acceleration: Disabled
- STP - Enabled
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Not currently forwarding any ports
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 36, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- No: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- No: UPnP, DMZ, QoS
- No: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
