Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ Unofficial Kong's release repository : http://ddwrt-kong.clonevince.fr/
Two pieces of RT-AC56U (main router, each) seem to work ok. Err, no, my mobile phone keeps associating and deassociating. _________________ 2 times APU2 Opnsense 21.1 with Sensei
2 times RT-AC56U running DD-WRT 45493 (one as Gateway, the other as AP, both bridged with LAN cable)
3 times Asus RT-N16 shelved
E4200 V1 running freshtomato 2020.8 (bridged with LAN cable)
3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running freshtomato 2020.8 (bridged with LAN cable)
Last edited by slobodan on Sun Oct 22, 2017 23:17; edited 1 time in total
Problems on DIR-890l also. 33575m flashes and comes up ok. OpenVPN client working. After 5-10 minutes, GUI stops responding and no new connections out are possible. Existing connections work. SSH does not work later, but seems ok if established in the first few min. Reverting to 33525m, which was very nice. Sorry, forgot to grab a look at a log.
It is possible, that the DHD units (e.g. R8X) need a new radio firmware to work with the new auth daemon. So far I only tested R6400/R7000 both work fine as AP or Client _________________ KONG PB's: http://www.desipro.de/ddwrt/
KONG Info: http://tips.desipro.de/
Posted: Mon Oct 23, 2017 10:34 Post subject: R8000
This build seems to be broke on the R8000. Setup everything, nothing extra just a access point, tried to connect wireless but it say no internet connection available. Reverted back to 10/16 build.
i have also some issue with that build ... just tested on a netgear R6250 .... very slow wifi on 2.4ghz .... 1~54 mbps connection mostly .... lots of errors ,device standing next to me
Joined: 18 Mar 2014 Posts: 12917 Location: Netherlands
Posted: Mon Oct 23, 2017 12:49 Post subject:
Router Model: Netgear R6400
Firmware Version: DD-WRT v3.0-r33575M kongac (10/22/17)
Kernel Version: Linux 4.4.94 #456 SMP Sun Oct 22 22:42:48 CEST 2017 armv7l
Upgraded: from DD-WRT v3.0-r33525M kongac (10/16/17) via ddup --flash-latest
Reset: No not this time
Status: Up and running for 3 hours, basic setup as AP, static leases, OpenVPN client ( on PIA) up and running, 2,4GHz, 5Ghz USB storage and DLNA working.
Errors: Yes, OpenVPN with Policy Based Routing does not forward HTTP(s) traffic to the PBR clients with SFE on see: http://svn.dd-wrt.com/ticket/5900.