Joined: 18 Mar 2014 Posts: 12917 Location: Netherlands
Posted: Sun Dec 23, 2018 12:51 Post subject:
Router: Linksys EA2000 (converted 320N)
Firmware: DD-WRT v3.0-r38060 mega (12/20/2018)
Kernel: Linux 2.6.24.111 #5530 Thu Dec 20 00:32:25 CET 2018 mips
Reset:Yes before and after with GUI reset and nvram erase
Mode: Gateway/AP
Status: Serious errors, but working
Joined: 08 May 2018 Posts: 14247 Location: Texas, USA
Posted: Sun Dec 23, 2018 14:45 Post subject:
egc wrote:
Router: Linksys EA2000 (converted 320N)
Firmware: DD-WRT v3.0-r38060 mega (12/20/2018)
Kernel: Linux 2.6.24.111 #5530 Thu Dec 20 00:32:25 CET 2018 mips
Reset:Yes before and after with GUI reset and nvram erase
Mode: Gateway/AP
Status: Serious errors, but working
There should still be other tickets quoted in there, and I have an ongoing list that I'm trying to track down whether or not they have been resolved as FIXED:
Posted: Mon Dec 24, 2018 2:05 Post subject: ASUS RT-AC68R
Currently I'm running DD-WRT v3.0-r37305 std 10/10/10 on my ASUS RT-AC68R and I am having an issue with the Router Management page & logging in. After originally flashing the v3.0-r37305 upgrade after factory resetting and reaching the fresh flash "Create a Web Management Login & Password" then setting it everything is straight. But once the router gets reset I am unable to login to the Web Management page any longer as I am assuming there is a bug within the v3.0-r37305 firmware that somehow the credentials I created no longer work and I have to factory reset with the push reset button which is positioned on the rear of the router....
Has anyone else experienced this issue with v3.0-r37305 on the Asus RT-AC68R and has this been fixed with this Alpha release?
Router/Version: Linksys EA6350 v2
File: DD-WRT v3.0-r38060 std (12/20/1
Kernel: Linux 4.4.168
Mode: AP
Status: one issue
I have strange problem with WiFi 2,4 protection after router restart.
Described here: https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1146385#1146385 and in a fev more posts I treid to add some information.
I noticed this in r37305 but r38060 behaves the same.
Posted: Mon Dec 24, 2018 18:49 Post subject: WEB GUI issue with Gateway Mode
Router/Version: Netgear R6400 v1
Firmware: DD-WRT v3.0-r38060 std (12/20/18 )
Kernel: Linux 4.4.168 #4350 SMP Wed Dec 19 10:28:58 CET 2018 armv7l
Previous: DD-WRT v3.0-r37860 std (11/27/1
Mode/Status: Gateway & AP
Reset: Yes / Yes
Issues/Errors: Yes / No (AP)
I have two R6400 V1 units. One is the gateway and the other is a hardwired AP. In generally both work with the new revision. The issue is with the Gateway, over time (sometimes a matter of minutes) that units WEB GUI fails to respond but it still routes traffic and WiFi is functional. A telnet into the device and can see that HTTPD is running. I can stop and start that service and the web interface will run again for a little while as you can see it slow in response as it gets close to failing to respond.
On the gateway, I don't remember seeing the web gui fail to respond while it wasn't routing to the WAN (I had setup after reset and reboot before configuring the IP address properly.)
I tried an earlier version (37961) which fails as well so it was introduced recently. It works fine on (37860).
Joined: 09 Nov 2014 Posts: 314 Location: Bakersfield, CA
Posted: Tue Dec 25, 2018 21:28 Post subject:
Router/Version: 2x Linksys E3000
File: dd-wrt.v24-38060_NEWD-2_K3.x_mega-e3000.bin
Previous: dd-wrt.v24-37932_NEWD-2_K3.x_mega-e3000.bin
Kernel: Linux 3.10.108-d7 #22227 Thu Dec 20 16:25:40 CET 2018 mips
Mode: Both client bridges, with all settings NOT required for a client bridge turned off. Basic setup.
Status: So far so good, no http hangs and speedtests seem fine. :)
Router/Version: Trendnet TEW811DRU
Firmware: DD-WRT v3.0-r38060 mini (12/20/18)
Previous: 37932
Kernel: Linux 4.4.168 #4353 Thu Dec 20 09:14:41 CET 2018 armv7l
Mode: AC only client bridge with all settings NOT required for a client bridge turned off. Basic setup.
Status: Working better than the last build.
Note: This build seems to load webpages slightly faster. Maybe it's just me, but it's noticeable. haha _________________ Deployed Routers:
Netgear R7800 - 1x build 46979
- Gateway (USB /w Entware, CAKE QoS)
Netgear R7000 - 3x build 46979
Joined: 29 Dec 2007 Posts: 26 Location: Maryland, USA
Posted: Wed May 01, 2019 1:53 Post subject:
vikramdinesh wrote:
Cannot upgrade to this build on Dlink DIR-890L A1 from build 37961. Get upgrade failed error.
Did you ever get this or any newer build to load on your 890? I'm at 32170 and having problems with my 890 with all my IoT devices lose their connection when I apply any settings change. Have to reboot to restore the connections.