Posted: Fri Feb 02, 2024 15:20 Post subject: New Build - 02/02/2024 - r55052
Welcome to Marvell r55052 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 30 May 2017 Posts: 582 Location: Rural Manitoba
Posted: Fri Feb 02, 2024 18:43 Post subject:
Same problem on 3200 as with 55033. With WAN connected unit goes into continuous reboots. If WAN is removed the unit starts and runs fine. Last known proper operation is on r55009. _________________ Starlink & DSL -> TPLink TL-R470T+
->
WRT3200acm Master WDS 5GHz 80Mhz CH 100 (+6) r55819
Ath1 2.4Ghz Disabled
99 Static Leases
ExpressVPN
WRT3200acm r55819 WDS Station 5Ghz
Ath1 AP N/G Mixed Channel 11 HT40
WRT1900Ac V1 5Ghz r55819 WDS Station
(Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1 5Ghz AC 80Mhz WDS Station r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT1900ACS SPARE r54914
WRT1900AC SPARE r54914
WRT1900AC V1 5Ghz AC 80Mhz WDS-AP r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT54G DD-WRT v3.0-r37305 micro AP CH 6 Mixed - Not in use
Linksys WRT3200ACM
GUI update from r55033 to r55052, no reset.
Used as Wired AP, no WAN.
No reboot issue here - all ok. _________________ ------------------------------------
Linksys WRT3200ACM DD-WRT r55819 (Gateway)
Linksys EA8500 OpenWrt-23.05.3 (Wired AP)
Netgear WNDR3700v4 DD-WRT r55819 (spare Gateway)
Photos: https://www.flickr.com/photos/nickant44/albums
Linksys WRT3200ACM
GUI update from r55033 to r55052, no reset.
Used as Wired AP, no WAN.
No reboot issue here - all ok.
WENED wrote:
Same problem on 3200 as with 55033. With WAN connected unit goes into continuous reboots. If WAN is removed the unit starts and runs fine. Last known proper operation is on r55009.
OK, maybe we have a problem when WAN is enabled. My router is also configuered to get the IP from provider over WAN. I can`t install this and also the last version.
best regards
Last edited by Fritzbuf on Sat Feb 03, 2024 11:54; edited 1 time in total
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r55052 std (02/02/24) (prev. DD-WRT v3.0-r55033 std (01/29/24))
Kernel: Linux 6.1.75 #277 SMP Fri Feb 2 05:52:10 +07 2024 arm
Mode: Gateway, SFE disabled, QoS in use, Wifi disabled, Wireguard for external access, WAN to DSL Modem, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning, using my own local NTP
Reset: No
Status: Installed yesterday, OK.
Router/Version: Linksys WRT1200AC v1
File: ddwrt-linksys-wrt1200ac-webflash.bin
Firmware: DD-WRT v3.0-r55052 std (02/02/24) (prev. DD-WRT v3.0-r55033 std (01/29/24))
Kernel: Linux 6.1.75 #277 SMP Fri Feb 2 05:52:10 +07 2024 arm
Mode: Gateway, SFE disabled, Wifi disabled, WAN disabled, Wireguard Endpoint for external VPS, connected via LAN to R7800, Keep Alive reboot 6:05 in the morning, using my own local NTP
Reset: No
Status: Installed yesterday, OK.
Router: Linksys WRT1900ACSv2
Firmware: DD-WRT v3.0-r55052 std (02/02/24) from r55009 std (01/23/24)
Kernel: Linux 6.1.75 #277 SMP Fri Feb 2 05:52:10 +07 2024 arm
Reset:: Yes. Without a reset, the router reboots cyclically.
Samba: Protocol Version SMB 2.10\SMB 3.11
SMB is buggy, reported here.
Issues/Errors:
My router starts rebooting cyclically when I try to configure the Firewall. It took a million years to figure this out. _________________ Linksys WRT1900ACSv2
Automatically adjustable temperature, always within the range of 59-68°С.
Router: Linksys WRT32X
Firmware: DD-WRT v3.0-r55052 std (02/02/24)
File: ddwrt-linksys-wrt32x-webflash.bin
Kernel: Linux 6.1.75 #277 SMP Fri Feb 2 05:52:10 +07 2024 arm
Previous/Reset: DD-WRT v3.0-r55033 std (01/29/24) / Yes
Mode/Status: Gateway (PPPOE, ignore WAN DNS, non-default router IP), WAN to ONT, AP, wlan0 5GHz AC-only VHT80 WPA2-Personal-CCMP, wlan1 2.4Ghz N-only HT40 WPA2-Personal-CCMP, wlan2 disabled, DDNS (SSL), encrypt DNS (DNSSEC, check unsigned DNS replies), virtual interface (2.4GHz, unbridged, AP isolation, net isolation, DHCPD, web UI disabled), ssh (non-default port, public key, password login disabled, remote management, TCP forwarding), wireguard server (non-default port, preshared key), WPS button radio-off enabled / Uptime 32 hrs.
Issues/Errors: None, except for minor bug with WPS button radio-off (more below).
Reset before and after update; cold reboot after each reset. No problems observed with continuous rebooting (setup has WAN to ONT). Low latency and good wireless speeds on wlan0 5Ghz : fast enough to max-out fiber connection (300-down/100-up) to ISP. Good stability after reset, even with SFE enabled (default setting). Good stability in ssh tunnelling and in wireguard tunnelling, even from clients connected over a cellular network. Tested with Linux-Intel NIC and Android-Qualcomm SoC clients. Thanks devs.
Minor bug - WPS button radio-off : after radios have been deactivated with first button press, radios do not always reactivate consistently with second button press. Sometimes wlan0 5GHz reactivates, but not wlan1 2.4GHz nor wlan1.1 2.4GHz. Other times, wlan1 and wlan1.1 2.4GHz reactivate, but not wlan0 5GHz (not a deal breaker, simply flagging).
------
Router/Version: Linksys WRT1900AC v1
Firmware: DD-WRT v3.0-r55052 std (02/02/24)
File: ddwrt-linksys-wrt1900ac-webflash.bin
Kernel: Linux 6.1.75 #185 SMP Mon Jan 29 05:42:35 +07 2024 arm
Previous/Reset: DD-WRT v3.0-r55033 std (01/29/24) / No
Mode/Status: Gateway (PPOE, ignore WAN DNS, non-default router IP), WAN to ONT, AP, wlan0 2.4GHz HT40 N-only WPA2-Personal-CCMP, wlan1 5GHz VHT80 AC-only WPA2-Personal-CCMP, virtual interface (2.4GHz, WPA2-Personal-CCMP, unbridged, AP isolation, net isolation, DHCPD, web UI disabled), DDNS (SSL), encrypt DNS (DNSSEC, check unsigned DNS replies), ssh (non-default port, public key, password login disabled, remote management, TCP forwarding), wireguard server (non-default port, preshared key), WPS button radio-off enabled / Uptime 29hrs.
Issues/Errors: None, WPS button radio-off bug observed for WRT32X is not observed for WRT1900 AC v1.
Last edited by ewo32 on Wed Feb 07, 2024 3:21; edited 3 times in total
Trying to copy anything from a Windows Machine towards the Routers smb enabled USB drive lets it reboot in an instant.
I did not stumble over this until now, since I usually SCP anything towards it.
And retrieving the data from my other connected devices works without problems.
Change(s) (to smbd?) after 1/2/24 r54682 are causing my WRT3200ACM to reboot when transferring via SMB (from Windows 10) to flash drive attached to router.
Router/Version: Linksys WRT1900AC v1
Firmware: DD-WRT v3.0-r55052 std (02/02/24)
Kernel: Linux 6.1.75 #277 SMP Fri Feb 2 05:52:10 +07 2024 arm
Mode: Gateway, SFE Enabled, Wifi 2.5 and 5GHz
Reset: Yes
Issues/Errors: Router started rebooting non-stop. I did the upgrade without a reset, and the problem was fixed after reseting and entering the configuration manually.
I was using 54682, but I was getting random reboots every other day. There was no real pattern, one day 2 reboots, the other all fine, another day 1 reboot, and so on and forth.
It's too soon to say reboots will happen again, but if it does I will update this post
Edit: Random reboots are also happening with this build.
Joined: 04 Aug 2018 Posts: 1447 Location: Appalachian mountains, USA
Posted: Fri Feb 09, 2024 20:24 Post subject:
welton wrote:
Edit: Random reboots are also happening with this build.
Try disabling SFE. It has worked for many others. _________________ 2x Netgear XR500 and 3x Linksys WRT1900ACSv2 on 53544: VLANs, VAPs, NAS, station mode, OpenVPN client (AirVPN), wireguard server (AirVPN port forward) and clients (AzireVPN, AirVPN, private), 3 DNSCrypt providers via VPN.
