Posted: Sun Jan 14, 2024 6:52 Post subject: New Build - 01/14/2024 - r54914
Welcome to Marvell r54914 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: WRT1900AC V1
File/Kernel: r54914
Previous/Reset: Upgrade
Mode/Status: Still have SFE disabled and I haven't had any crashes since disabling
Issues/Errors: None
Noticed that both firmware versions (ddwrt-linksys-wrt1900ac-webflash.bin and factory-to-ddwrt.bin) are the same ~35MB filesize now. Historically, factory-to-ddwrt always used to be about half the size of the upgrade images, and then when the builds stopped working they were both the same size but the smaller ~15MB size. Now they're both the larger ~35MB. Is this going to be the case going forward, and does anyone know why they used to be such different sizes?
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r54914 std (01/14/24)
Kernel: Linux 6.1.72 #235 SMP Sun Jan 14 03:23:42 +07 2024 arm
Mode: Gateway, SFE disabled, QoS in use, Wifi disabled, Wireguard for external access, WAN to DSL Modem, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed two days ago, OK.
Router/Version: Linksys WRT3200ACM
File/Kernel: r54914 / Linux 6.1.72 #235 SMP Sun Jan 14 03:23:42 +07 2024 arm
Previous/Reset: r54682 / upgrade, factory defaults after boot, enter new settings (always)
Mode/Status: AP, basic home internet and media server / reverted to r54682 due to smb causing reboots
Issues/Errors: smb transfer causes router to reboot at completion
same as r54905:
Quote:
Change(s) (to smbd?) after 1/2/24 r54682 are causing my WRT3200ACM to reboot when transferring via SMB (from Windows 10) to flash drive attached to router. When copy progress hits 99%, it freezes and router reboots. (same transfer via FTP works properly) After reboot, when smb is again accessible, it seems the file finished transferring successfully before the reboot. r54682 and earlier have been working properly over many years.
Router Model Linksys WRT1900ACS
Firmware Version DD-WRT v3.0-r54914 std (01/14/24)
Kernel Version Linux 6.1.72 #235 SMP Sun Jan 14 03:23:42 +07 2024 arm
Router/Version: Linksys WRT1900ACS v2
File/Kernel: Linux 6.1.72 #235 SMP Sun Jan 14 03:23:42 +07 2024 arm
Previous/Reset: upgrade, factory defaults after boot, enter new settings
Mode/Status: AP, basic home internet
Issues/Errors: No internet after every hard shutdown
I'm running this version on a Linksys WRT1900ACSV2, upgraded and reset to factory settings and it seems to work properly until a hard shutdown on the router happens. When the router is turned on again, the wifi does not work anymore. The wireless interface is on 5GHz, AP, AC / N Mixed, VHT80, TX power 15dBm and also SFE off btw.
I'm not sure when this started happening because I don't remember what was my last working version anymore and I also did a reset to factory settings so from my last working version there could have been changes in the config that I don't have around anymore.
System logs do not show any error or anything relevant. Everything else seem to work fine, I can connect to the network and use internet when wired.
I can try to bisect and find a working version but I wonder if there's something somebody know I could try/check before doing that.
I'm running this version on a Linksys WRT1900ACSV2, upgraded and reset to factory settings and it seems to work properly until a hard shutdown on the router happens. When the router is turned on again, the wifi does not work anymore. The wireless interface is on 5GHz, AP, AC / N Mixed, VHT80, TX power 15dBm and also SFE off btw.
Do you have the 2.4ghz AP enabled and know if that still works? I'm curious because I've experienced similar issues where after the router starts up, occasionally only the 5ghz AP wouldn't work, although it resolved for me by rebooting it (usually but not always). When this happened, some of the status values under Status>Wireless>wlan1 (my 5ghz AP) reported "Unknown". Sorry I don't have any suggestions about how to fix it.
I only have 5ghz enabled. I was thinking about testing this out, turning both things off, unplugging the router cable and then restarting it again to see what happens. Going to try it out and report back, still of someone has ideas I'd like to hear about things to try.
I can confirm that when 2.4ghz is enabled alone or with both 2.4 and 5ghz on, everything works perfectly fine.
If I turn on only 5ghz, after a shutdown and turning on the router again, I don’t have the wifi accessible anymore.
