Well I did manage to get one EA8500 on r53815. Working for about 10 days now. _________________ ......All GOOD here... Just Handshakes and Time Stamps !......
I managed to get r54079 on one of my EA8500s. It was a lengthy process using the TFTP method; flashed to both partitions. Twelve reboots and two NVRAM resets (auto resets) later it finally booted. It's been running fine now for nearly 12 hours but it's not doing anything useful. Under load it could be a completely different story. USB2 port seems to be working w/USB3 64GB Sandisk flash stick and I didn't test the USB3 port as earlier k6.1 builds broke two USB sticks already. _________________ Linksys EA8500 (Internet Gateway, AP/VAP) - DD-WRT r53562
Features in use: WDS-AP, Multiple VLANs, Samba, WireGuard, Entware: mqtt, mlocate
Wireless 5ghz only
Netgear R7800 (WDS-AP, WAP, VAP) - DD-WRT r55779
Features in use: multiple VLANs over single trunk port
Linksys EA8500 WDS Station x2 - DD-WRT r55799
Netgear R6400v2 WAP, VAP 2.4ghz only w/VLANs over single trunk port. DD-WRT r55779
OSes: Fedora 38, 9 RPis (2,3,4,5), 20 ESP8266s: Straight from Amiga to Linux in '94, never having owned a Windows PC.
Router/Version: Netgear V7500v2
Kernel: Linux 6.1.62 #44 SMP Mon Nov 13 07:34:10 +07 2023 arm
Previous/Reset: 53939 / No Reset
Mode: Gateway+AP, SFE Disabled, STP Disabled, Wifi 5(VANILLA)/2.4(VANILLA) Main+Guest(VAP), DNSMasq, USB(3.2, Ext2)/Entware, DNSCrypt, NAS/Samba, Static & DHCP
Issues/Errors: Upgraded smoothly and booted perfectly. Noticed new code to disconnect previously connected USB drive during shutdown/startup?. All appears to be working well.
Thanks to BS and crew for all your good work.
Code:
...
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [24772608] at [0x017A0000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [24903680] at [0x017C0000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [25034752] at [0x017E0000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [25165824] at [0x01800000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [25296896] at [0x01820000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [25427968] at [0x01840000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [25559040] at [0x01860000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [25690112] at [0x01880000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [25821184] at [0x018A0000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [25952256] at [0x018C0000]
Nov 18 17:25:20 192.168.1.1 user info [flash] : write block [26083328] at [0x018E0000]
Nov 18 17:25:21 192.168.1.1 user info [flash] : write block [26214400] at [0x01900000]
Nov 18 17:25:21 192.168.1.1 user info [flash] : done [26345472]
Nov 18 17:25:25 192.168.1.1 user info [init] : Terminated....................................
Nov 18 17:25:25 192.168.1.1 kern info kernel [243757.902112] xhci-hcd xhci-hcd.1.auto: remove, state 1
Nov 18 17:25:25 192.168.1.1 kern info kernel [243757.902150] usb usb4: USB disconnect, device number 1
Nov 18 17:25:25 192.168.1.1 kern info kernel [243757.906231] usb 4-1: USB disconnect, device number 2
Nov 18 17:25:25 192.168.1.1 kern info kernel [243758.007013] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
Nov 18 17:25:25 192.168.1.1 kern info kernel [243758.007078] xhci-hcd xhci-hcd.1.auto: remove, state 1
Nov 18 17:25:25 192.168.1.1 kern info kernel [243758.011749] usb usb3: USB disconnect, device number 1
Nov 18 17:25:25 192.168.1.1 user debug wsdd2[3214] 'Terminated' signal received.
Jan 1 00:00:15 192.168.1.1 kern info kernel [ 15.755391] device br0 left promiscuous mode
Jan 1 00:00:15 192.168.1.1 user debug mac80211: start deconfigure_single_ath9k
Jan 1 00:00:15 192.168.1.1 user debug mac80211: start delete_ath9k_devices
Jan 1 00:00:15 192.168.1.1 user debug mac80211: leave delete_ath9k_devices
Jan 1 00:00:15 192.168.1.1 user debug mac80211: leave deconfigure_single_ath9k
Jan 1 00:00:15 192.168.1.1 user debug mac80211: start deconfigure_single_ath9k
Jan 1 00:00:15 192.168.1.1 user debug mac80211: start delete_ath9k_devices
Jan 1 00:00:15 192.168.1.1 user debug mac80211: leave delete_ath9k_devices
Jan 1 00:00:15 192.168.1.1 user debug mac80211: leave deconfigure_single_ath9k
...
Last edited by whitebeard on Sat Nov 18, 2023 18:05; edited 3 times in total
I managed to get r54079 on one of my EA8500s. It was a lengthy process using the TFTP method; flashed to both partitions. Twelve reboots and two NVRAM resets (auto resets) later it finally booted. It's been running fine now for nearly 12 hours but it's not doing anything useful...
Just thinking... Q: now that it's up and running, did you try to reflash using normal web/cli methods? _________________ Current: Netgear R9000 DD-WRT v3.0-r55460 std (03/25/24)
Retired: Linksys WRT32X r39296, TP-Link Archer C7 v2, LinkSys WRT54G v5
I managed to get r54079 on one of my EA8500s. It was a lengthy process using the TFTP method; flashed to both partitions. Twelve reboots and two NVRAM resets (auto resets) later it finally booted. It's been running fine now for nearly 12 hours but it's not doing anything useful...
Just thinking... Q: now that it's up and running, did you try to reflash using normal web/cli methods?
I will try once the next release comes out.
Partition 2 is still non-bootable, so I am not hopeful it will work unless the specific undetermined problem gets addressed. I suspect the problem could be with the ipq806x kernel config but my post regarding that has yet to have any other opinions posted. _________________ Linksys EA8500 (Internet Gateway, AP/VAP) - DD-WRT r53562
Features in use: WDS-AP, Multiple VLANs, Samba, WireGuard, Entware: mqtt, mlocate
Wireless 5ghz only
Netgear R7800 (WDS-AP, WAP, VAP) - DD-WRT r55779
Features in use: multiple VLANs over single trunk port
Linksys EA8500 WDS Station x2 - DD-WRT r55799
Netgear R6400v2 WAP, VAP 2.4ghz only w/VLANs over single trunk port. DD-WRT r55779
OSes: Fedora 38, 9 RPis (2,3,4,5), 20 ESP8266s: Straight from Amiga to Linux in '94, never having owned a Windows PC.
Router/Version: R7800
File/Kernel: Linux 6.1.62 #44 SMP Mon Nov 13 07:34:10 +07 2023 armv7l
Previous/Reset: r53939 / Nope
Mode/Status: setup PPPoE connection, Gateway and AP
Issues/Errors: After hours of use the modem spontaneously reboots
Conclusion: Not stable !
Note: version r53939 had the same issues on my R7800 _________________ Regards,
Vaako
1x Netgear R7800 Nighthawk - firmware not decided yet !!!!
1x Netgear R7000 Nighthawk r36410
1x Ubiquiti RouterStation Pro DD-WRT r23204 std (12/24/13)
1x Asus RT-N16 SVN revision 20675 NEWD-2 K2.6
1x Linksys E4200 v3.0 r34777 mega (01/31/18 )
1x Buffalo WZR-HP-G300NH B0 B0 Gargoyle FW
1x Linksys WRT600N v1.1 (Bricked)
1x Linksys WRT54GL v1.1 (DD-WRT 26446)
1x Linksys WRT54GS v2.2 (DD-WRT 26446)
1x Linksys RVS4000 (stock fw)
3x D-Link DWL-7100AP (openWRT)
2x TP-Link TL-WA801ND (Bridge mode) 100mW TX-Power
Asus WL-520GU SVN 16403M NEWD-2 Eko std-nokaid
4x Fonera with Gargoyle FW
Router/Version: R7800
File/Kernel: DD-WRT v3.0-r54079 std (11/17/23)
Kernel Version: Linux 6.1.62 #44 SMP Mon Nov 13 07:34:10 +07 2023 armv7l
Previous Build /Reset: r52330 k4.9 (Now is Backup Router) / YES, GUI Update Router Swap -> Hard-Reset -> Manual Config -> k6.1 Online after Power Cycle
Mode/Status: GW / Working Well
Issues/Errors: GW speed is 600mps with k6.1 (k4.9 was +900mps) / none
Services Used: DHCP-WAN,IPv6-6to4,NTP,WG-Client,VLAN-GUI,BR1-7,SSH,Syslog,Cron,USB-Storage,Entware DNSCrypt v2.1.2,Performance Mode
Services Disabled: Both-Radios,QoS,ttraff,SFE,Telnet,NAS,Samba,YAMon3.4.6
Running over 13 hours
Home Main AP Router
Router/Version: R7800
File/Kernel: DD-WRT v3.0-r54079 std (11/17/23)
Kernel Version: Linux 6.1.62 #44 SMP Mon Nov 13 07:34:10 +07 2023 armv7l
WiFi DD-WRT Firmware: 10.4-ddwrt-9984-tW-13-7264 api 5 features mfp,peer-flow-ctrl,allows-mesh-bcast,peer-fixed-rate,superchannel crc32 f46c9632
WiFi Vanilla Firmware: 10.4-3.18-00002 api 5 features no-p2p,mfp,peer-flow-ctrlllows-mesh-bcast,no-ps,peer-fixed-rate crc32 9959da8e
Previous Build/Reset: r52330 k4.9 (Now is Backup Router) / YES, GUI Update Router Swap -> Hard-Reset -> Manual Config -> k6.1 Online after Power Cycle
Mode/Status: GW(double-nat) & AP / Working Well
Issues/Errors: none / none
Services Used: Vanilla 2.4Ghz-20Mhz & 5Ghz-160Mhz Radios,Static-WAN,IPv6-6to4,NTP,2xWG-Clients,VAPx,VLAN-GUI,BR0-7,SSH,Syslog,Cron,USB Storage,Entware DNSCrypt v2.1.2,Performance Mode
Services Disabled: SPI,QoS,ttraff,SFE,Telnet,NAS,Samba
Running for 16 hours.
No Reboots followed what others have done with k6.1 use default Performance Mode and other disabled services. This is my 1st test run with k6.1 (on spare r7800 with factory defaults and manually configured) and all my services are all working on both R7800s only my Gigabit Service is limited to 600Mps.
Thank-you BrianSlyer for your Great Work and everyone else who makes DD-WRT Great on the Forum! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Be careful with using the on demand governor on K6.1. There is a possible problem with cache coherency when the CPU switches which can cause reboots.
removed it from all my R7800's no more random reboot's ... CPU is running + 1-2C so, not a big difference ..
What did you do to solve these random reboots ?
Please tell because it's driving me nuts
If you are using the ondemand governor script, disable or remove it... <wink> _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Sun Nov 19, 2023 4:40 Post subject:
Vaako wrote:
What did you do to solve these random reboots ?
Please tell because it's driving me nuts
I did a magic...
in order to help you out, we need to know lots of details ...so, tell us what do you have running...
-services
-options
-scripts and ect..
PIC's of your set up preferred...
i suspect..SFE, SAMBA, QoS, wrong 5GHZ channels...VPN that doesn't support DCO..or WG..SmartDNS may be...? _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
What did you do to solve these random reboots ?
Please tell because it's driving me nuts
I did a magic...
in order to help you out, we need to know lots of details ...so, tell us what do you have running...
-services
-options
-scripts and ect..
PIC's of your set up preferred...
i suspect..SFE, SAMBA, QoS, wrong 5GHZ channels...VPN that doesn't support DCO..or WG..SmartDNS may be...?
I have nothing running specially, SFE was on and I turned it off now to see if this helps.
No SAMBA
No QoS
5GHz works great never have issues with it.
No VPN
No SmartDNS
Before I was runining r53445 and it did run without issues.
Then I installed r53843 and can't remeber if I got any problems with that version.
But I'm 100% sure that the issues started from r53939 that the random reboots accurs and therefore I upgraded to r54079 in hope that this problem would be solved.
What pic's do you need, some schreenshots of my settings ? _________________ Regards,
Vaako
1x Netgear R7800 Nighthawk - firmware not decided yet !!!!
1x Netgear R7000 Nighthawk r36410
1x Ubiquiti RouterStation Pro DD-WRT r23204 std (12/24/13)
1x Asus RT-N16 SVN revision 20675 NEWD-2 K2.6
1x Linksys E4200 v3.0 r34777 mega (01/31/18 )
1x Buffalo WZR-HP-G300NH B0 B0 Gargoyle FW
1x Linksys WRT600N v1.1 (Bricked)
1x Linksys WRT54GL v1.1 (DD-WRT 26446)
1x Linksys WRT54GS v2.2 (DD-WRT 26446)
1x Linksys RVS4000 (stock fw)
3x D-Link DWL-7100AP (openWRT)
2x TP-Link TL-WA801ND (Bridge mode) 100mW TX-Power
Asus WL-520GU SVN 16403M NEWD-2 Eko std-nokaid
4x Fonera with Gargoyle FW
Netgear WNDR3700 V4main gateway
DD-WRT v3.0-r54079 std (11/17/23)
Linux 3.18.140-d6 #185013 Fri Nov 17 12:03:08 +06 2023 mips
GUI install over r53939
usually just backup main router but I stuck him in a bit ago after the update just to see iffin old guy still worked.
No QOS / NO OVPN server / NO samba like I run on main EA8500
does have VLAN on port (closest to WAN) via br1 w/ wlan0.1 & wlan1.1
old thang still suits me
Left the EA8500 running r54079 most of the weekend and all seemed good. Power cycled it this afternoon, and four hours and twenty minutes later, it is still boot looping. Sigh. _________________ Linksys EA8500 (Internet Gateway, AP/VAP) - DD-WRT r53562
Features in use: WDS-AP, Multiple VLANs, Samba, WireGuard, Entware: mqtt, mlocate
Wireless 5ghz only
Netgear R7800 (WDS-AP, WAP, VAP) - DD-WRT r55779
Features in use: multiple VLANs over single trunk port
Linksys EA8500 WDS Station x2 - DD-WRT r55799
Netgear R6400v2 WAP, VAP 2.4ghz only w/VLANs over single trunk port. DD-WRT r55779
OSes: Fedora 38, 9 RPis (2,3,4,5), 20 ESP8266s: Straight from Amiga to Linux in '94, never having owned a Windows PC.
Left the EA8500 running r54079 most of the weekend and all seemed good. Power cycled it this afternoon, and four hours and twenty minutes later, it is still boot looping. Sigh.
