Entware DNSCrypt-Proxy V2 on DDWRT

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> General Questions
Goto page 1, 2, 3  Next
Author Message
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1405
Location: Canada

PostPosted: Tue Aug 06, 2019 15:43    Post subject: Entware DNSCrypt-Proxy V2 on DDWRT Reply with quote
Here's my example of Entware's DNScrypt-Proxy V2 on R7000 & R7800 using Cisco Servers

I tested Entware DNScrypt-Proxy V2 on 2 routers
- R7000 with Kongac Build 39855M
- R7800 with Kongat Build 39855M

Reference Websites on installing Entware
https://wiki.dd-wrt.com/wiki/index.php/Installing_Entware
https://github.com/Entware/Entware/wiki

To view all supported DNSCrypt-Proxy V2 Servers: https://dnscrypt.info/public-servers

For the R7000 & R7800 I used the ARMv7 based installation given in the DD-WRT Wiki (Link from above). My configuration example will be based on Content Filtering with Cisco Servers.

Once Entware is installed you will need install the correct DNScrypt-Proxy V2 package for your router.
- For the R7000 in CLI run "opkg install dnscrypt-proxy2_nohf" without quotes.
- For the R7800 in CLI run "opkg install dnscrypt-proxy2" without quotes.
- I also use YAMon3 and also ran in CLI "opkg install ip-full" without quotes

I also needed to edit /opt/etc/dnscrypt-proxy.toml (I also made a back up of the original file). There are many settings in the file but only configured the following to use Cisco Servers...
- server_names = ['cisco', 'cisco-ipv6']
- listen_addresses = ['127.0.0.1:30', '[::1]:30']
- ipv6_servers = true
- require_nofilter = false
- fallback_resolver = '208.67.220.220:53'

Since I'm using ip-full with YAMon3 I also edited /opt/YAMon3/config.file and changed the these setting to _path2ip='/opt/sbin/ip' & _includeIPv6='1' and restarted YAMon3.

I also edited DNSMasq in the GUI...
- Enable No DNS Rebind
- Addition Options
no-ping
no-resolv
all-servers
domain-needed
server=/ntp.org/208.67.220.220
server=127.0.0.1#30
server=::1#30
quiet-dhcp

To start DNSCrypt-Proxy V2 here my startup commands:

# Startup Script
# Start Entware Services
sleep 10
/opt/etc/init.d/rc.unslung start

To stop DNSCrypt-Proxy V2 in Shutdown commands:

# Shutdown Script
# Stop Entware Services
sleep 10
/opt/etc/init.d/rc.unslung stop

_________________
Home Network on Telus PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway WiFi 3xVPN - KONGAT 39855M
E3000 - Gateway Wired IPTV - DDWRT r35531 Mega
WHR-HP-G54 - Internal Routing - DDWRT r35531 std-special

______________________
Off Site 1

R7000 - Gateway & WiFi & VPN - KONGAC 39855M
WRT610Nv1 - Repeater Bridge - DDWRT r33679 Mega K2.4

__________________________
Off Site 2

2x R7000 - Data Gateway, WiFi & IPTV WiFi, PVR Blocker- KONGAC 39855M

__________________
YAMon 3.4 | Ad-Blocking for DD-WRT | DNSCrypt-Proxy V2
Sponsor
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 3065
Location: UK, London, just across the river..

PostPosted: Wed Aug 07, 2019 9:43    Post subject: Reply with quote
great guide all is working as described by mac913
few Q points:
this guide works only with DNScrypt v2 and uses only v2 public servers,
all those i tested non v2 ware not working...

i used those settings in /opt/etc/dnscrypt-proxy.toml

server_names = ['dnscrypt.uk-ipv4', 'dnscrypt.nl-ns0']
listen_addresses = ['127.0.0.1:30']
ipv4_servers = true
ipv6_servers = false
dnscrypt_servers = true
require_dnssec = true
doh_servers = false
fallback_resolver = '9.9.9.9:53'

*do notice to set the server_names = you have to delete/uncomment the # (hashtag) its very on the top

in my Additional DNSmasq rules

dhcp-option=43,01:04:00:00:00:02
no-negcache
no-ping
filterwin2k
domain-needed
bogus-priv
no-resolv
server=127.0.0.1#30
quiet-dhcp

as NTP server IP i use settings

Basic Setup>Time Settings>Server IP/Name 216.239.35.4
------

to use an old DNScrypt version instead, still present on Kong builds (R7800)
and be able to use all not v2 DNScrypt public servers i used this guide by mac913 too

*do notice this do not require any entware installation"

add to Additional DNSmasq rules
no-resolv
domain-needed
server=127.0.0.1#30
server=127.0.0.2#30

add those lines in startup script

RESOLVER_FILE="/etc/dnscrypt/dnscrypt-resolvers.csv"
dnscrypt-proxy -S -m 5 -a 127.0.0.1:30 -R dnscrypt.eu-nl -L /etc/dnscrypt/dnscrypt-resolvers.csv -d
dnscrypt-proxy -S -m 5 -a 127.0.0.2:30 -R dnscrypt.eu-dk -L /etc/dnscrypt/dnscrypt-resolvers.csv -d

*do notice those public resolvers used here are DNSSEC verified servers, you can use your favorite servers from
https://dnscrypt.info/public-servers/..., you can add as many as you want!!

_________________
Atheros
TP-Link WR740Nv1 ------DD-WRT 33772 BS WAP/Switch (wired)
TP-Link WR1043NDv2 ----DD-WRT 41659 BS (AP,PPPoE,NAT,AD Blocking,AP Isolation,Firewall,Local DNS,Forced DNS,DoT, VPN)
TP-Link WR1043NDv2 ----DD-WRT 41664 BS (AP,NAT,AD Blocking,Firewall,Wi-Fi OFF,Local DNS,Forced DNS,DoT)
TP-Link WR1043NDv2 ----Gargoyle OS 1.11.0 (AP,NAT,QoS,Quotas)
Qualcomm/IPQ8065
2x Netgear R7800 -------DD-WRT 40270M 4.9 Kong (AP,NAT,AD-Blocking,AP&Net Isolation,VLAN's,Firewall,Local DNS,DNSCrypt-proxy v2 x2)
Broadcom
Netgear R7000 -------DD-WRT 40270M Kong (AP,NAT,VLAN,AD-Blocking,Firewall,Local DNS,Forced DNS,DoT)
------------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 via Entware by mac913
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 3065
Location: UK, London, just across the river..

PostPosted: Sat Sep 14, 2019 18:07    Post subject: Reply with quote
hmmm for some reason i cant't make it work on my
1043v2 (mipsel)unit, i use "opkg install dnscrypt-proxy2" but than i cant start it...

/opt/etc/init.d/rc.unslung start

it doesn't starts it...

do i need to make a start up script .sh like...
i don't remember how i deployed it on my R7800, but followed all the steps
above and it, was successful..sadly im away from that unit and the record how to... Razz

_________________
Atheros
TP-Link WR740Nv1 ------DD-WRT 33772 BS WAP/Switch (wired)
TP-Link WR1043NDv2 ----DD-WRT 41659 BS (AP,PPPoE,NAT,AD Blocking,AP Isolation,Firewall,Local DNS,Forced DNS,DoT, VPN)
TP-Link WR1043NDv2 ----DD-WRT 41664 BS (AP,NAT,AD Blocking,Firewall,Wi-Fi OFF,Local DNS,Forced DNS,DoT)
TP-Link WR1043NDv2 ----Gargoyle OS 1.11.0 (AP,NAT,QoS,Quotas)
Qualcomm/IPQ8065
2x Netgear R7800 -------DD-WRT 40270M 4.9 Kong (AP,NAT,AD-Blocking,AP&Net Isolation,VLAN's,Firewall,Local DNS,DNSCrypt-proxy v2 x2)
Broadcom
Netgear R7000 -------DD-WRT 40270M Kong (AP,NAT,VLAN,AD-Blocking,Firewall,Local DNS,Forced DNS,DoT)
------------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 via Entware by mac913
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1405
Location: Canada

PostPosted: Sun Sep 15, 2019 6:31    Post subject: Reply with quote
I haven't tested on MIPSEL hardware.

Quote:
Once Entware is installed you will need install the correct DNScrypt-Proxy V2 package for your router.
- For the R7000 in CLI run "opkg install dnscrypt-proxy2_nohf" without quotes.
- For the R7800 in CLI run "opkg install dnscrypt-proxy2" without quotes.
- I also use YAMon3 and also ran in CLI "opkg install ip-full" without quotes


There are 2 packages, are you using dnscrypt-proxy2_nohf for MIPSEL?

_________________
Home Network on Telus PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway WiFi 3xVPN - KONGAT 39855M
E3000 - Gateway Wired IPTV - DDWRT r35531 Mega
WHR-HP-G54 - Internal Routing - DDWRT r35531 std-special

______________________
Off Site 1

R7000 - Gateway & WiFi & VPN - KONGAC 39855M
WRT610Nv1 - Repeater Bridge - DDWRT r33679 Mega K2.4

__________________________
Off Site 2

2x R7000 - Data Gateway, WiFi & IPTV WiFi, PVR Blocker- KONGAC 39855M

__________________
YAMon 3.4 | Ad-Blocking for DD-WRT | DNSCrypt-Proxy V2
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 3065
Location: UK, London, just across the river..

PostPosted: Sun Sep 15, 2019 9:31    Post subject: Reply with quote
nope i used the standard one that was compatible with Qualcomm R7800 "opkg install dnscrypt-proxy2" ...

should i use the other one instead...??
is opkg install dnscrypt-proxy2_nohf the right one for mipsel....??? i doubt ...

_________________
Atheros
TP-Link WR740Nv1 ------DD-WRT 33772 BS WAP/Switch (wired)
TP-Link WR1043NDv2 ----DD-WRT 41659 BS (AP,PPPoE,NAT,AD Blocking,AP Isolation,Firewall,Local DNS,Forced DNS,DoT, VPN)
TP-Link WR1043NDv2 ----DD-WRT 41664 BS (AP,NAT,AD Blocking,Firewall,Wi-Fi OFF,Local DNS,Forced DNS,DoT)
TP-Link WR1043NDv2 ----Gargoyle OS 1.11.0 (AP,NAT,QoS,Quotas)
Qualcomm/IPQ8065
2x Netgear R7800 -------DD-WRT 40270M 4.9 Kong (AP,NAT,AD-Blocking,AP&Net Isolation,VLAN's,Firewall,Local DNS,DNSCrypt-proxy v2 x2)
Broadcom
Netgear R7000 -------DD-WRT 40270M Kong (AP,NAT,VLAN,AD-Blocking,Firewall,Local DNS,Forced DNS,DoT)
------------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 via Entware by mac913
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1405
Location: Canada

PostPosted: Mon Sep 16, 2019 16:10    Post subject: Reply with quote
Alozaros wrote:
nope i used the standard one that was compatible with Qualcomm R7800 "opkg install dnscrypt-proxy2" ...

should i use the other one instead...??
is opkg install dnscrypt-proxy2_nohf the right one for mipsel....??? i doubt ...


The "dnscrypt-proxy2" will not run on an R7000 what makes MIPSEL better? The "dnscrypt-proxy2" must have special instruction set that works on the R7800. The "dnscrypt-proxy2_nohf" build must have a reduced instruction set for SoC with less processing hardware in it.

My guess "_nohf" may mean No Hardware Floating point support, don't known.

_________________
Home Network on Telus PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway WiFi 3xVPN - KONGAT 39855M
E3000 - Gateway Wired IPTV - DDWRT r35531 Mega
WHR-HP-G54 - Internal Routing - DDWRT r35531 std-special

______________________
Off Site 1

R7000 - Gateway & WiFi & VPN - KONGAC 39855M
WRT610Nv1 - Repeater Bridge - DDWRT r33679 Mega K2.4

__________________________
Off Site 2

2x R7000 - Data Gateway, WiFi & IPTV WiFi, PVR Blocker- KONGAC 39855M

__________________
YAMon 3.4 | Ad-Blocking for DD-WRT | DNSCrypt-Proxy V2
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 2613
Location: Texas, USA

PostPosted: Mon Sep 16, 2019 16:55    Post subject: Reply with quote
A WR1043NDv2 is not an R7800. IPQ8065 with a Krait is not the lower-end Atheros. R7800 is an ARM processor, not a MIPS. I thought this was a known fact?
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 3065
Location: UK, London, just across the river..

PostPosted: Mon Sep 16, 2019 20:48    Post subject: Reply with quote
kernel-panic69 wrote:
A WR1043NDv2 is not an R7800. IPQ8065 with a Krait is not the lower-end Atheros. R7800 is an ARM processor, not a MIPS. I thought this was a known fact?


well to make clear, i know all of that...above

what i didn't know is, what was the meaning of nohf..
VARIANT:=nohf
DEPENDS:=@TARGET_armv7_3_2||@TARGET_armv7_2_6 +ca-bundle

now i know...about nohf....
i had a believe, it was Broadcom related only...
armv7_3_2 & armv7_2_6...is a Broadcom....
but that was a guess... Razz

the other interesting bit is in my entware packages i can see only dnscrypt-proxyV2...
available...??

while dnscrypt-proxy2 requires only +ca-bundle and i do have it installed too
so that must be the right way...or im missing something???


so far, i made it work on R7000 and R7800
haven't made it yet, for 1043v2...

_________________
Atheros
TP-Link WR740Nv1 ------DD-WRT 33772 BS WAP/Switch (wired)
TP-Link WR1043NDv2 ----DD-WRT 41659 BS (AP,PPPoE,NAT,AD Blocking,AP Isolation,Firewall,Local DNS,Forced DNS,DoT, VPN)
TP-Link WR1043NDv2 ----DD-WRT 41664 BS (AP,NAT,AD Blocking,Firewall,Wi-Fi OFF,Local DNS,Forced DNS,DoT)
TP-Link WR1043NDv2 ----Gargoyle OS 1.11.0 (AP,NAT,QoS,Quotas)
Qualcomm/IPQ8065
2x Netgear R7800 -------DD-WRT 40270M 4.9 Kong (AP,NAT,AD-Blocking,AP&Net Isolation,VLAN's,Firewall,Local DNS,DNSCrypt-proxy v2 x2)
Broadcom
Netgear R7000 -------DD-WRT 40270M Kong (AP,NAT,VLAN,AD-Blocking,Firewall,Local DNS,Forced DNS,DoT)
------------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 via Entware by mac913
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 2613
Location: Texas, USA

PostPosted: Mon Sep 16, 2019 21:49    Post subject: Reply with quote
Does the disabled FPU issue affect Entware like it does Optware? .... That's the only thing I can think of, unless there is a separate package for MIPS.
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 3065
Location: UK, London, just across the river..

PostPosted: Tue Sep 17, 2019 12:22    Post subject: Reply with quote
donno
will not hurt to try nohf...will see..
otherwise i do have entware and other packages installed and its ok...on this router...

kernel-panic69 wrote:
That's the only thing I can think of, unless there is a separate package for MIPS.


http://bin.entware.net/mipselsf-k3.4/Packages.html

_________________
Atheros
TP-Link WR740Nv1 ------DD-WRT 33772 BS WAP/Switch (wired)
TP-Link WR1043NDv2 ----DD-WRT 41659 BS (AP,PPPoE,NAT,AD Blocking,AP Isolation,Firewall,Local DNS,Forced DNS,DoT, VPN)
TP-Link WR1043NDv2 ----DD-WRT 41664 BS (AP,NAT,AD Blocking,Firewall,Wi-Fi OFF,Local DNS,Forced DNS,DoT)
TP-Link WR1043NDv2 ----Gargoyle OS 1.11.0 (AP,NAT,QoS,Quotas)
Qualcomm/IPQ8065
2x Netgear R7800 -------DD-WRT 40270M 4.9 Kong (AP,NAT,AD-Blocking,AP&Net Isolation,VLAN's,Firewall,Local DNS,DNSCrypt-proxy v2 x2)
Broadcom
Netgear R7000 -------DD-WRT 40270M Kong (AP,NAT,VLAN,AD-Blocking,Firewall,Local DNS,Forced DNS,DoT)
------------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 via Entware by mac913
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1405
Location: Canada

PostPosted: Wed Sep 18, 2019 4:56    Post subject: Reply with quote
Your package list in your post is for Broadcom MIPSEL.

https://wiki.dd-wrt.com/wiki/index.php/Installing_Entware

The above link will help with loading the correct installer.

Quote:
For MIPS based devices (Atheros, not dual core), this will be:

cd /opt (click enter)
wget http://bin.entware.net/mipssf-k3.4/installer/generic.sh (click enter)
sh generic.sh (click enter)

_________________
Home Network on Telus PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway WiFi 3xVPN - KONGAT 39855M
E3000 - Gateway Wired IPTV - DDWRT r35531 Mega
WHR-HP-G54 - Internal Routing - DDWRT r35531 std-special

______________________
Off Site 1

R7000 - Gateway & WiFi & VPN - KONGAC 39855M
WRT610Nv1 - Repeater Bridge - DDWRT r33679 Mega K2.4

__________________________
Off Site 2

2x R7000 - Data Gateway, WiFi & IPTV WiFi, PVR Blocker- KONGAC 39855M

__________________
YAMon 3.4 | Ad-Blocking for DD-WRT | DNSCrypt-Proxy V2
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 3065
Location: UK, London, just across the river..

PostPosted: Wed Sep 18, 2019 9:47    Post subject: Reply with quote
well, i wrote this article,....
and i do have the correct packages...my installations are fine...

just posted that link from the article, package's are
showing and there is no nohf, if those ware for Broadcoms...if you got me wrong....

but anyway ill keep trying...

_________________
Atheros
TP-Link WR740Nv1 ------DD-WRT 33772 BS WAP/Switch (wired)
TP-Link WR1043NDv2 ----DD-WRT 41659 BS (AP,PPPoE,NAT,AD Blocking,AP Isolation,Firewall,Local DNS,Forced DNS,DoT, VPN)
TP-Link WR1043NDv2 ----DD-WRT 41664 BS (AP,NAT,AD Blocking,Firewall,Wi-Fi OFF,Local DNS,Forced DNS,DoT)
TP-Link WR1043NDv2 ----Gargoyle OS 1.11.0 (AP,NAT,QoS,Quotas)
Qualcomm/IPQ8065
2x Netgear R7800 -------DD-WRT 40270M 4.9 Kong (AP,NAT,AD-Blocking,AP&Net Isolation,VLAN's,Firewall,Local DNS,DNSCrypt-proxy v2 x2)
Broadcom
Netgear R7000 -------DD-WRT 40270M Kong (AP,NAT,VLAN,AD-Blocking,Firewall,Local DNS,Forced DNS,DoT)
------------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 via Entware by mac913
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1405
Location: Canada

PostPosted: Wed Sep 18, 2019 14:47    Post subject: Reply with quote
Yes you are correct, I don't see a nohf version in the MIPS builds. If I have time I will try to load on a Broadcom E3000 and post back.

Lately I've playing XWRT-Vortex on a R7000 with a special setup for ISP IPTV Boxes with isolated PVR (no recording access) to Renters.

_________________
Home Network on Telus PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway WiFi 3xVPN - KONGAT 39855M
E3000 - Gateway Wired IPTV - DDWRT r35531 Mega
WHR-HP-G54 - Internal Routing - DDWRT r35531 std-special

______________________
Off Site 1

R7000 - Gateway & WiFi & VPN - KONGAC 39855M
WRT610Nv1 - Repeater Bridge - DDWRT r33679 Mega K2.4

__________________________
Off Site 2

2x R7000 - Data Gateway, WiFi & IPTV WiFi, PVR Blocker- KONGAC 39855M

__________________
YAMon 3.4 | Ad-Blocking for DD-WRT | DNSCrypt-Proxy V2
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 3065
Location: UK, London, just across the river..

PostPosted: Wed Sep 18, 2019 17:26    Post subject: Reply with quote
well i already tried/succeeded with R7000 it was ok..
as well on R7800...
DNScryptv2 on TP1043v2 is my problem now ...
so far, DoT on it runs flawlessly..haven tried unbound, yet... Smile

ON R7000 im a bit afraid to jump around different, 3 rd party's,
as they tend to screw CFE sometimes and im not willing to deal
with it..so far i tried Tomato on it...hmm was ok...
but DD-WRT seems kind of better and more updated...working or not...

sadly Kong's gone now...... a bit of a wonder what to do with R7000....and R7800

on R7800 OpenWRT is not my taste but tried it in the past, quite scatchy and things
ware not always working as intended... but it was a hail of a shit to
set via Luci...(that was pulling me away)...but once you find out, what it what
it was ok...
yep XWRT-Vortex on R7000 looks like a asuswrt-merlin https://www.asuswrt-merlin.net/
will be fun to try...is it safe i read it needed an updated CFE...
than it wont be that easy to go back to DDWRT...???

_________________
Atheros
TP-Link WR740Nv1 ------DD-WRT 33772 BS WAP/Switch (wired)
TP-Link WR1043NDv2 ----DD-WRT 41659 BS (AP,PPPoE,NAT,AD Blocking,AP Isolation,Firewall,Local DNS,Forced DNS,DoT, VPN)
TP-Link WR1043NDv2 ----DD-WRT 41664 BS (AP,NAT,AD Blocking,Firewall,Wi-Fi OFF,Local DNS,Forced DNS,DoT)
TP-Link WR1043NDv2 ----Gargoyle OS 1.11.0 (AP,NAT,QoS,Quotas)
Qualcomm/IPQ8065
2x Netgear R7800 -------DD-WRT 40270M 4.9 Kong (AP,NAT,AD-Blocking,AP&Net Isolation,VLAN's,Firewall,Local DNS,DNSCrypt-proxy v2 x2)
Broadcom
Netgear R7000 -------DD-WRT 40270M Kong (AP,NAT,VLAN,AD-Blocking,Firewall,Local DNS,Forced DNS,DoT)
------------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 via Entware by mac913
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1405
Location: Canada

PostPosted: Wed Sep 18, 2019 17:57    Post subject: Reply with quote
Going off topic...

The only reason I'm testing/playing with Xwrt-Vortex on the R7000 is that the ISP's IPTV Boxes only connect wirelessly via WPS (DD-WRT does not support it). I only loaded up the Firmware so I don't know if the CFE changed. Xwrt-Vortex latest release is on kernel 2.6 so I only plan to using it on internal networks. I too prefer DD-WRT.

From what I read (have not done it) going back to DD-WRT...
1) Factory Default Xrt-Vortex
2) Load Netgear Firmware
3) Factory Default Netgear
4) Load DD-WRT
5) Factory Default DD-WRT

_________________
Home Network on Telus PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway WiFi 3xVPN - KONGAT 39855M
E3000 - Gateway Wired IPTV - DDWRT r35531 Mega
WHR-HP-G54 - Internal Routing - DDWRT r35531 std-special

______________________
Off Site 1

R7000 - Gateway & WiFi & VPN - KONGAC 39855M
WRT610Nv1 - Repeater Bridge - DDWRT r33679 Mega K2.4

__________________________
Off Site 2

2x R7000 - Data Gateway, WiFi & IPTV WiFi, PVR Blocker- KONGAC 39855M

__________________
YAMon 3.4 | Ad-Blocking for DD-WRT | DNSCrypt-Proxy V2
Goto page 1, 2, 3  Next Display posts from previous:    Page 1 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> General Questions All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum