[ho1Aetoo]

the r9000 does not have an Atheros CPU but a Qudcore from Annapurna Labs, the CPU itself is more powerful than the IPQ807x series...

the IPQ807x still needs NPU coprocessors due to poor network design and lack of offload functions...

Only the IPQ95xx series has enough performance to achieve enough throughput without NPU cores.

[Zyxx]

Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r53763 std (10/24/23) (prev. DD-WRT v3.0-r53714 std (10/20/23))
Kernel: Linux 6.1.59 #60 SMP Tue Oct 24 07:06:32 +07 2023 arm
Mode: Gateway, SFE disabled, QoS in use, Wifi disabled, Wireguard for external access, WAN to DSL Modem, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed a few hours ago, OK. Wireguard is working again, thank you =)

[kernel-panic69]

A little update. I noticed that somewhere along the way, the USB 3 (not USB | eSATA) port no longer powers my USB fan. Didn't have the knack to plug into the other port, using an external USB power source. Image for reference only.



EDIT: Logs attached, got my USB fan connected to the USB 2 | eSATA port and it works.

EDIT 2: Ticket #7712 (WRT3200ACM - USB 3.0 port turn off at start up) created by dance85

[oliver44]

[nickant]

Router: WRT3200ACM
Version: DD-WRT v3.0-r53763 std (10/24/23)
File: ddwrt-linksys-wrt3200acm-webflash.bin
Kernel: Linux 6.1.59 #60 SMP Tue Oct 24 07:06:32 +07 2023 arm
Previous: DD-WRT v3.0-r53633
Reset: No
Mode: AP
Status: Ok
Uptime: ~1 hour
Issues/Errors: None to report at present

This WRT3200ACM is the only 6.1 kernel router updated via GUI.
My EA-8500 and WRT1900ACv1 both bounce back to earlier 4.9 builds.

[lexridge]

[nickant]

[Rickers]

Router/Version: WRT1900ACv1
File/Kernel: 53763 (ddwrt-linksys-wrt1900ac-webflash.bin)
Previous/Reset: 53562/No Reset
Mode/Status: AP
Issues/Errors: As with 53734, my router won't boot 53763. After a slight delay, it boots into the previous build 53562.

[Zyxx]

@oliver44 not that I'm aware of.
No speed issues observed so far.

What port was affected?
Does it flicker between 100 and 1000?
Or how do you check for this?
When does it happen?

My WAN connection on this device is only 10 Mbit/s.
Could use iperf though.

[oliver44]

I notice this problem in my speed test, I only have 100 Mbps and when I check the network card in the PC it is set to 100 Mbps link, only if I disconnect and then reconnect it returns to 1000 Mbps, it is possible that the ports on the router have problems, this problem that happens randomly once or twice a week happens on all ports on the router!

I have already announced this problem and I have seen other users who also reported this problem on the OpenWrt forum

https://forum.openwrt.org/t/21-02-rc4-mt7530-mdio-bus-1f-lan1-link-is-down-link-is-up/102931/44?page=3

[Zyxx]

@oliver44:

I'm going to have an eye on this. Currently I tested every 30 minutes since your answer.

Router - switch - router
iperf3 reaches ~750-800 Mbit/s

Router - switch - PC
iperf3 reaches ~950 Mbit/s

No Phy Problems observed so far, will continue to monitor and test this the next few days.

[kosmos]

Since this version, I've had connection drops every minute again. When I'm surfing something in the evening when there's no activity, the connection drops are every 12 minutes. What's remarkable is that it's always just after a full minute. Alo some recurring event could be the cause.

[dale_gribble39]

That shows the entries in your RPi, Is there anything in your DD-WRT router syslog?

[kosmos]

yes i can see when it kicked out the Rpi again.

The syslog constantly returns what is known
Oct 28 12:02:04 DD-WRT-EG daemon.info hostapd: wlan0: STA xx:xx:xx:xx:xx IEEE 802.11: disassociated
Oct 28 12:02:05 DD-WRT-EG daemon.info hostapd: wlan0: STA xx:xx:xx:xx:xx IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)

or

[dale_gribble39]

@kosmos: Without screenshots of your current settings, basic and advanced, for wifi, and the tell-tale upnp entries, it's a shot in the dark on what to suggest - but I suspect it to be a configuration issue or client issue. Does this happen every hour per default GTK renewal interval? The Marvell driver doesn't support certain settings for wifi, so, this may be where the problem lies (configuration), or not.