Posted: Mon Jan 29, 2024 14:56 Post subject: New Build - 01/29/2024 - r55033
Welcome to Atheros r55033 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Netgear 7800
File/Kernel: 01/29/2024 - r55033
Previous/Reset: r54682 / YES
Mode/Status: normal / light off
Issues/Errors: I install r55033 but the light or router is off, all light. After this I reset the router and started putting all the settings again. After many settings and reboots the router was fine, unfortunately at some point the LAN LEDs are turned off. Which one causes the problem to appear is hard to say. Solutions?
I reinstall old version r54682 with old configuration. Identical problem with previous firmware version 2024.
Linksys E2100L
DD-WRT v3.0-r55033 std (01/29/24)
Linux 3.10.108-d11 #151630 Mon Jan 29 06:18:40 +06 2024 mips
GUI install over r54914
WAP + OVPN server all ok
OpenVPN 2.6.8 server seem okydoky on this oldass thang
#
Linksys WRT160NL
DD-WRT v3.0-r55033 std (01/29/24)
Linux 3.10.108-d11 #151626 Mon Jan 29 06:13:34 +06 2024 mips
GUI install over r54914
WAP + OVPN server worky ok
Router/Version: Netgear 7800
File/Kernel: 01/29/2024 - r55033
Previous/Reset: r54682 / YES
Mode/Status: normal / light off
Issues/Errors: I install r55033 but the light or router is off, all light. After this I reset the router and started putting all the settings again. After many settings and reboots the router was fine, unfortunately at some point the LAN LEDs are turned off. Which one causes the problem to appear is hard to say. Solutions?
I reinstall old version r54682 with old configuration. Identical problem with previous firmware version 2024.
I don't remember which LEDs were lit with 12-18-2023-r54545 (the router is not in a visible place), but when I upgraded to 01-23-2024-r55009, no LEDs were lit. Then I downgraded the firmware with some random versions (all with Linux 6.1) and had no luck (still no LEDs working). At the end, I downgraded to 10-03-2023-r53562 (Linux 4.9) and the LEDs were lit again. I upgraded back to 01-23-2024-r55009 and now the first four LEDs from the left (power, internet, and both WiFis) are lit, but the LAN is still not working (I don't use USB and I don't know if it is lit or not).
Yeah, strange behavior.
Last edited by uvz123a on Tue Jan 30, 2024 9:19; edited 1 time in total
Status - Crash - downgraded to 54914 (SMB works properly in 54914)
Explanation:
Since Public build 55003 - SMB Usage Causes router crash - requires hard reboot to restore access, dorps both wired and wireless, though LED indicators make it look like its functioning. I believe this happens on any write operation - but i could not gather logs to verify.
Mod edit: Stop disabling BBCode in your posts, please. Thx. -kp69
Last edited by nyddwrtuser330 on Tue Jan 30, 2024 15:15; edited 1 time in total
Joined: 12 Dec 2007 Posts: 783 Location: Pittsburgh, PA USA
Posted: Tue Jan 30, 2024 15:19 Post subject:
Router/Version: Netgear R7800 x 3
File/Kernel: DD-WRT v3.0-r55033 std (01/29/24)
Previous/Reset: DD-WRT v3.0-r55009 std (01/23/24), last reset at 54905
Mode/Status: Gateway (SFE disabled), Access Point (VANILLA firmware,2.4GHz, 5GHZ, WPA2/WPA3, 802.11r/v/k), IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS/DNSMasq, OpenVPN server, Wireguard Server + 2 wired access points (VANILLA firmware,2.4GHz, 5GHZ, WPA2/WPA3, 802.11r/v/k)
Issues/Errors:
Up 18 hours. USB 2.0 working properly for Entware and "jffs" partitions. Wireguard and OpenVPN servers working as expected and throughput sufficient to open video files on network shares. Speed (tested via nPerf.com) is close to or greater than what my ISP advertizes, both wired and wireless. SFE remains disabled. Router LAN lights not working but all other lights working. My routers are not in a visible place, so lights don't matter much.
Getting glitching on some streaming services but not others. Probably the streaming services themselves but the timing makes it suspicous. Upgraded around 4PM and saw it last night but hadn't seen it the night before. Will do some testing and see.
EDIT: After putting my backup router (R7800 identically configured running 54905) in place, the stuttering was still observed. Pretty sure it's just a problem with Freevee and Pluto, not with DD-WRT. The timing was just coincidental.
Router/Version: Netgear R7800
File: dd-wrt-webupgrade.bin
Firmware: DD-WRT v3.0-r55033 std (01/29/24)
Kernel: Linux 6.1.75 #105 SMP Fri Jan 26 17:06:37 +07 2024 armv7l
Mode: Gateway, SFE disabled, 2.4G and 5G wifi (FW: DD-WRT), Wireguard for external access, WAN to 4G Bridge (DHCP Client), Keep Alive reboot 6:02 in the morning, using my own local NTP
Reset: No
Status: Installed two days ago, OK. Cyclic NTP Update does only start after it receives a WAN connection. So to set initial time after boot, I added "ntpclient ipofmyNTP" into startup.
I don't know if this a wanted behaviour or an error. Will just report once, since it does function when WAN is disabled.
I suspect - normal unfavorable behavior when WAN is activated.
The firewall is also only started when the WAN connection is established. (e.g. network isolation only becomes active when a WAN connection is established)
Router/Version: TP-Link TL-WR841ND v11
Update method: WebUpgrade
File/Kernel: tl-wr841nd-webflash.bin_r55033 std / Linux 3.18.140-d6 #191545 Mon Jan 29 08:00:39 +06 2024 mips
Previous/Reset: r55009 / no
Mode/Status: AP wired and wireless / Up and running for 1:18 hours
Issues/Errors: Nothing significant
The fact is that the router connected to the Internet (to the Internet provider). And it reports an error, the orange WAN indicator flashes (the icon in the form of a planet). Internet is working, I just think it's a glitch
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 54545
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 56029
Broadcom
Asus RT-AC87U R - DD-WRT 56029
Asus RT-N66U - DD-WRT 55819
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
