Posted: Sat Sep 10, 2022 15:51 Post subject: New Build - 09/10/2022 - r50146
Welcome to Atheros r50146 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Linksys EA8500...main gateway
DD-WRT v3.0-r50146 std (09/10/22)
Linux 4.9.327 #1198 SMP Sat Sep 10 01:13:14 +07 2022 armv7l
up 'bout 12 minutes seems ok so far
Noticed this (linked to in blkt original post) r50146 had different sha256sum so...
GUI install over:
DD-WRT v3.0-r50146 std (09/10/22)
Linux 4.9.327 #1194 SMP Fri Sep 9 18:05:32 +07 2022 armv7l
it twas all good ---> did have uptime 22:12
#
Netgear WNDR3700 V4
DD-WRT v3.0-r50146 std (09/10/22)
Linux 3.18.140-d6 #152657 Sat Sep 10 19:43:56 +07 2022 mips
switch / ovpn server ... uptime 14 min
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r50146 std (09/10/22)
Kernel Version Linux 4.9.327 #646 SMP Fri Sep 9 12:44:42 +07 2022 armv7l
Current Time Sat, 10 Sep 2022 14:54:58
Uptime 1 min
GUI over 50057
Reset: no
Issue: upgraded fine
Joined: 03 Nov 2015 Posts: 317 Location: Florida, USA
Posted: Sun Sep 11, 2022 0:53 Post subject:
Router: Linksys ea8500 ..WDS AP
Firmware: DD-WRT v3.0-r50146 std (09/10/22)
Kernel: Linux 4.9.327 #1198 SMP Sat Sep 10 01:13:14 +07 2022 armv7l
Reset: No ...GUI upgrade from r50057
Errors: None
Router: Linksys ea8500 ..WDS Stations ... X (2)
Firmware: DD-WRT v3.0-r50146 std (09/10/22)
Kernel: Linux 4.9.327 #1198 SMP Sat Sep 10 01:13:14 +07 2022 armv7l
Reset: No ...GUI upgrade from r50057
Errors: None
***** Fast smooth upgrades on all 3. Last build (r50057) were all up 6 days,12 hrs.+ with zero
issues. Last 5-6 builds have been excellent performance wise as well. Thanks to all the devs
and BS who make this happen ! _________________ ......All GOOD here... Just Handshakes and Time Stamps !......
r50146 is all good ... went outside with laptop on hood of truck so I can
get good signal from a few places just to double-check my openVPN servers.
They is all very good---noticed this build is still on version 2.5.7
my Debian laptop uses openvpn version 2.6 but tis all good
connected to all 3 without a problem...even ssh into each while connected
yeahuh I still like using old DH stuffs
main gateway EA8500
Code:
Citadel-Station-Homeworld daemon.notice openvpn[2105]: Diffie-Hellman initialized with 4096 bit key
WNDR3700v4
Code:
Citadel-Switch daemon.notice openvpn[935]: Diffie-Hellman initialized with 2048 bit key
other EA8500
Code:
EA8500 daemon.notice openvpn[1174]: Diffie-Hellman initialized with 2048 bit key
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Sun Sep 11, 2022 12:32 Post subject: New Build - 09/10/2022 - r50146
Router/Version: Tp-Link TL-WDR3600 v 1.5
Kernel: Linux 3.10.108-d11 #116108 Sat Sep 10 16:49:11 +07 2022 mips
Reset: No
Mode: Internet gateway, WIFI 5GHz AP, dnsmasq, firewall
Issues: Some yellow and red marked events in logs. I'm paste that below
Status: Working
Uptime: more than 4h
Device working rather good. I have some warnings in logs. Performance of router is on good level.
Code:
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] cpu srif ddr srif cpu 560 ddr 450 ahb 225
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] Zone ranges:
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] Normal [mem 0x00000000-0x07ffffff]
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] Movable zone start for each node
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] Early memory node ranges
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.280000] registering PCI controller with io_map_base unset
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.280000] Can't analyze schedule() prologue at 800689c4
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.810000] nf_conntrack_rtsp v0.7 loading
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 0.810000] nf_nat_rtsp v0.7 loading
Jan 1 01:00:01 Myrouter kern.err kernel: [ 9.050000] gpiochip_find_base: cannot find free range
Jan 1 01:00:01 Myrouter kern.err kernel: [ 9.060000] gpiochip_add: gpios -1..21 (ath9k-phy0) failed to register
Jan 1 01:00:01 Myrouter kern.warn kernel: [ 9.070000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Jan 1 01:00:01 Myrouter kern.err kernel: [ 9.110000] gpiochip_find_base: cannot find free range
Jan 1 01:00:01 Myrouter kern.err kernel: [ 9.120000] gpiochip_add: gpios -1..14 (ath9k-phy1) failed to register
Jan 1 01:00:52 Myrouter daemon.err httpd[1286]: [httpd] : Request Error Code 401: Authorization required. Wrong username and/or password!
Sep 11 14:15:39 Myrouter daemon.err httpd[1286]: [httpd] : Request Error Code 401: Authorization required. Wrong username and/or password!
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Sun Sep 11, 2022 13:26 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r50146 std (09/10/22)
Kernel Version Linux 3.18.140-d6 #152629 Sat Sep 10 18:40:41 +07 2022 mips
Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r50146 std (09/10/22)
Kernel Version Linux 4.9.327 #1200 SMP Sat Sep 10 13:46:42 +07 2022 armv7l
Router Model Netgear Nighthawk X10
Firmware Version DD-WRT v3.0-r50146 std (09/10/22)
Kernel Version Linux 4.9.327 #646 SMP Fri Sep 9 12:44:42 +07 2022 armv7l
update: CLI r50057 > r50146
reset: NO
mode: Gateway
status: Operational 12h+1
errors: Nothing new, yet...Thanks BS, egc, Joker and members ! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Status: Working
Issues: The Syslog window is a few pixels to wide. I get a horizontal scrollbar with the Previous/Next buttons on top of it.
Same router and f/w here. No problem in the Syslog window, though.
FWIW: The router has been running long enough to have the start of the syslog scrolled into oblivion.