Netgear R7000P
From DD-WRT Wiki
(Difference between revisions)
Revision as of 22:59, 5 May 2020 (edit) Jeremywh7 (Talk | contribs) (cleanup) ← Previous diff |
Current revision (15:37, 22 June 2020) (edit) (undo) Jeremywh7 (Talk | contribs) m (fix forum link and add kong clonevince mirror link) |
||
Line 58: | Line 58: | ||
*Upgrade: netgear-'''r8000'''-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong) | *Upgrade: netgear-'''r8000'''-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong) | ||
*Reset after upgrade not usually required, but '''if you have issues, reset and manually set up''' first. | *Reset after upgrade not usually required, but '''if you have issues, reset and manually set up''' first. | ||
- | '''NOTE:''' The R7000P build target | + | '''NOTE:''' The R7000P build target is the same as R8000, so older builds were named ''netgear-r8000-webflash.bin''<br> |
[[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] & forum build threads for build recommendations | [[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] & forum build threads for build recommendations | ||
- | *Kong builds are deprecated but | + | *Kong builds are deprecated but a [http://ddwrt-kong.clonevince.fr/ mirror site] is linked there too. |
*Also see the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for historical information | *Also see the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for historical information | ||
Line 75: | Line 75: | ||
et robowr 0x0 0x1a 0x0 | et robowr 0x0 0x1a 0x0 | ||
This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands | This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands | ||
- | Reference: [https:// | + | Reference: [https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1118576#1118576 dcglabs' forum post] |
==Forum== | ==Forum== | ||
- | [https:// | + | [https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=310669 Do not use the Tathagata build.]<br> |
[[Category:Netgear guides]] | [[Category:Netgear guides]] |
Current revision
Contents |
[edit] Hardware Specifications
FCC ID | PY316200351 |
---|---|
Industry Canada ID | 4054A-16200351 |
Power | 12 VDC, 3.5 A |
CPU/SoC | Broadcom BCM4708C0 @ 1 GHz |
CPU Architecture | ARM Cortex A9 (2 cores) |
Flash (ROM) / RAM | 128 MiB / 256 MiB |
USB ports | 1x USB 3.0, 1x USB 2.0 |
Wireless1 chip | Broadcom BCM4365E |
Wireless2 chip | Broadcom BCM4360 |
WL1/WL2 protocols | an+ac / bgn |
MIMO config | 3x3:3 |
Antenna connectors | U.FL, RP-SMA |
Ethernet | Broadcom BCM4708C0 |
Switch | Broadcom BCM4708C0 |
LAN / WAN ports | 4 / 1 (up to 1 Gb/s) |
Serial | 4-pin header, internal, 3.3V TTL |
Supported in DD-WRT since Kong r32945M ( 7/31/17 )
[edit] Installation
Do not 30/30/30 reset ARM routers! Use the GUI Factory Defaults reset.
- DO NOT USE THE ROUTER DATABASE!
- Use builds in the netgear-r7000P directory (some are missing the factory-to-dd file)
- Initial flash: GUI reset then flash factory-to-dd-wrt.chk (BS) or dd-wrt.K3_R7000P.chk (Kong)
- Upgrade: netgear-r8000-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong)
- Reset after upgrade not usually required, but if you have issues, reset and manually set up first.
NOTE: The R7000P build target is the same as R8000, so older builds were named netgear-r8000-webflash.bin
Where do I download firmware? & forum build threads for build recommendations
- Kong builds are deprecated but a mirror site is linked there too.
- Also see the Peacock announcement for historical information
The R7000P is misidentified as R6400v1 in builds 36816 up to 37715, so users should avoid them.
[edit] Disable LEDs
In the GUI, go to Admin->Commands and save the following as a Startup Script, then reboot:
#!/bin/sh # for i in 2 3 8 9 10; do gpio enable $i ; done for i in 11 12 13; do gpio disable $i ; done et robowr 0x0 0x18 0x1ff et robowr 0x0 0x18 0x0 et robowr 0x0 0x1a 0x0
This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands Reference: dcglabs' forum post