Netgear R7000P

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 17:27, 16 March 2018 (edit)
Jeremywh7 (Talk | contribs)
(New page: ==[https://wikidevi.com/wiki/Netgear_R7000P Hardware] Specifications== {| border="1" cellspacing="0" !FCC ID |PY316200351 |- !Industry Canada ID |4054A-16200351 |- !Power |12 VDC, 3.5 A |-...)
← Previous diff
Current revision (15:37, 22 June 2020) (edit) (undo)
Jeremywh7 (Talk | contribs)
m (fix forum link and add kong clonevince mirror link)
 
(4 intermediate revisions not shown.)
Line 1: Line 1:
-==[https://wikidevi.com/wiki/Netgear_R7000P Hardware] Specifications==+==Hardware [http://techinfodepot.shoutwiki.com/wiki/Netgear_R7000P Specifications]==
{| border="1" cellspacing="0" {| border="1" cellspacing="0"
!FCC ID !FCC ID
Line 52: Line 52:
==Installation== ==Installation==
-'''Do not 30/30/30 reset ARM routers!''' Use the GUI Factory Defaults reset.+'''Do not 30/30/30 reset ARM routers!''' Use the GUI ''Factory Defaults'' reset.
-*BS: ''netgear-r7000P'' directory, but some are missing the factory-to-dd file+*'''DO NOT USE THE ROUTER DATABASE!'''
-*Kong: http://www.desipro.de/ddwrt/K3-AC-Arm/+*Use builds in the ''netgear-r7000P'' directory (some are missing the ''factory-to-dd'' file)
-**Initial flash: GUI reset then flash factory-to-dd-wrt.chk (BS) or dd-wrt.K3_R7000P.chk (Kong)+*Initial flash: GUI reset then flash factory-to-dd-wrt.chk (BS) or dd-wrt.K3_R7000P.chk (Kong)
-**Upgrade: netgear-'''r8000'''-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong)+*Upgrade: netgear-'''r8000'''-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong)
-**Reset after upgrade not usually required, but '''if you have issues, reset and manually set up''' first.+*Reset after upgrade not usually required, but '''if you have issues, reset and manually set up''' first.
-'''NOTE:''' The R7000P build target currently uses the r8000, so the webflash is named as such<br>+'''NOTE:''' The R7000P build target is the same as R8000, so older builds were named ''netgear-r8000-webflash.bin''<br>
-See the forum & [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for build recommendations, also: [[Firmware_FAQ#Where_do_I_download_firmware.3F|Where_do_I_download_firmware?]]+[[Firmware_FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] & forum build threads for build recommendations
 +*Kong builds are deprecated but a [http://ddwrt-kong.clonevince.fr/ mirror site] is linked there too.
 +*Also see the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement] for historical information
 + 
 +The R7000P is [https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=317434 misidentified as R6400v1] in builds 36816 up to 37715, so users should avoid them.
==Disable LEDs== ==Disable LEDs==
Line 71: Line 75:
et robowr 0x0 0x1a 0x0 et robowr 0x0 0x1a 0x0
This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands
-Reference: [https://www.dd-wrt.com/forum/posting_sec.php?mode=quote&p=1118576 dcglabs' forum post]+Reference: [https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1118576#1118576 dcglabs' forum post]
==Forum== ==Forum==
-[https://www.dd-wrt.com/forum/viewtopic.php?t=310669 Do not use the Tathagata build.]<br>+[https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=310669 Do not use the Tathagata build.]<br>
[[Category:Netgear guides]] [[Category:Netgear guides]]

Current revision

Contents

[edit] Hardware Specifications

FCC ID PY316200351
Industry Canada ID 4054A-16200351
Power 12 VDC, 3.5 A
CPU/SoC Broadcom BCM4708C0 @ 1 GHz
CPU Architecture ARM Cortex A9 (2 cores)
Flash (ROM) / RAM 128 MiB / 256 MiB
USB ports 1x USB 3.0, 1x USB 2.0
Wireless1 chip Broadcom BCM4365E
Wireless2 chip Broadcom BCM4360
WL1/WL2 protocols an+ac / bgn
MIMO config 3x3:3
Antenna connectors U.FL, RP-SMA
Ethernet Broadcom BCM4708C0
Switch Broadcom BCM4708C0
LAN / WAN ports 4 / 1 (up to 1 Gb/s)
Serial 4-pin header, internal, 3.3V TTL

Supported in DD-WRT since Kong r32945M ( 7/31/17 )

[edit] Installation

Do not 30/30/30 reset ARM routers! Use the GUI Factory Defaults reset.

  • DO NOT USE THE ROUTER DATABASE!
  • Use builds in the netgear-r7000P directory (some are missing the factory-to-dd file)
  • Initial flash: GUI reset then flash factory-to-dd-wrt.chk (BS) or dd-wrt.K3_R7000P.chk (Kong)
  • Upgrade: netgear-r8000-webflash.bin (BS) or dd-wrt.v24-K3_AC_ARM_R7000P.bin (Kong)
  • Reset after upgrade not usually required, but if you have issues, reset and manually set up first.

NOTE: The R7000P build target is the same as R8000, so older builds were named netgear-r8000-webflash.bin
Where do I download firmware? & forum build threads for build recommendations

The R7000P is misidentified as R6400v1 in builds 36816 up to 37715, so users should avoid them.

[edit] Disable LEDs

In the GUI, go to Admin->Commands and save the following as a Startup Script, then reboot:

#!/bin/sh
#
for i in 2 3 8 9 10; do gpio enable $i ; done
for i in 11 12 13; do gpio disable $i ; done
et robowr 0x0 0x18 0x1ff
et robowr 0x0 0x18 0x0
et robowr 0x0 0x1a 0x0

This can alternatively be ran manually (line by line or separated by ';') from telnet/ssh/Commands Reference: dcglabs' forum post

[edit] Forum

Do not use the Tathagata build.