Linksys E1200v2

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 15:33, 27 October 2020 (edit)
Jeremywh7 (Talk | contribs)
m (clarify upgrade and trailed builds a bit)
← Previous diff
Current revision (15:39, 27 October 2020) (edit) (undo)
Jeremywh7 (Talk | contribs)
m (Hardware - fix link)
 
Line 2: Line 2:
[[Image:E1200 Photo01.jpg | right | 350px]] [[Image:E1200 Photo01.jpg | right | 350px]]
-=Hardware [https://wikidevi.com/wiki/Linksys_E1200_v2 Information]=+=Hardware [http://techinfodepot.shoutwiki.com/wiki/Linksys_E1200_v2 Information]=
{| border="1" cellspacing="0" {| border="1" cellspacing="0"
! CPU ! CPU
Line 33: Line 33:
[1] - E1200v2 [http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1098154#1098154 has 64 KB more than most 8MB routers]: 8060928 bytes (7872 KB).<br> [1] - E1200v2 [http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1098154#1098154 has 64 KB more than most 8MB routers]: 8060928 bytes (7872 KB).<br>
'''Do NOT flash larger builds!''' '''Do NOT flash larger builds!'''
- 
= Flashing Instructions = = Flashing Instructions =

Current revision

This page applies to version 2. For version 1, see Linksys E1200

Contents

[edit] Hardware Information

CPU Broadcom BCM5357
CPU Speed 300 MHz
RAM/Flash ROM 32 MB / 8 MB [1]
Radio 2.4 GHz
WLAN Support b/g/n
WLAN Max Speed 300 Mb/s
Antenna Location Internal
Switch Ports 4 LAN/1 WAN (10/100 Mb/s)
USB Port None

[1] - E1200v2 has 64 KB more than most 8MB routers: 8060928 bytes (7872 KB).
Do NOT flash larger builds!

[edit] Flashing Instructions

WARNING: only use nv64k builds to upgrade. Don't confuse this with other Linksys E-Series units use nv60k builds!

  • These instructions were performed with an e1200v2 running FW_E1200_v2.0.07.002_US_20150108.bin
  1. With a wired connection, log into the Linksys Web Interface Firmware Upgrade page.
  2. Do a reset using the stock web interface. Wait a minute.
  3. Flash the initial flash firmware: dd-wrt.v24-19519_NEWD-2_K2.6_mini-e1200v2.bin
  4. Wait 2 minutes for the router to flash and reboot itself.
  5. Wait about another 2 minutes until it finishes booting.
  6. Log into the dd-wrt web interface and set a password
  7. Flash the -nv64k.bin upgrade build then when complete, reset using the GUI
    • Wait 3-4 minutes for the flash to complete, then if isn't accessible, manually power cycle the router

For download links, build information, and more: Where do I download firmware?

Minimum build with the Broadcom krack fixes is 33772. See here for more info.

[edit] No LAN ports After Reset

There is a persistent bug with some E-series routers in DD-WRT after a reset, where the LAN-ethernet ports are not bound to anything, and only wireless (WLAN) is working initially.

Fix: access the web interface using wireless and add vlan1 (ethernet ports) back to the bridge.

  • For a step-by-step and more details see here.


[edit] Recovering from Management Recovery Mode

Follow the E1500 directions, substituting e1500 for e1200v2 and using the appropriate firmware.


[edit] Reverting to Stock Firmware

Download the stock firmware image from the manufacturer's website (link), reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1