Linksys E1200
From DD-WRT Wiki
Revision as of 15:42, 24 December 2013 (edit) JNavas (Talk | contribs) m (edit) ← Previous diff |
Revision as of 17:33, 24 January 2019 (edit) (undo) Jeremywh7 (Talk | contribs) (→Flashing Instructions - Clarify initial vs upgrade flashes) Next diff → |
||
(15 intermediate revisions not shown.) | |||
Line 8: | Line 8: | ||
{| border="1" cellspacing="0" | {| border="1" cellspacing="0" | ||
! CPU | ! CPU | ||
- | | Broadcom [ | + | | Broadcom [https://wikidevi.com/wiki/Linksys_E1200_v1 BCM5357] |
|- | |- | ||
! CPU Speed | ! CPU Speed | ||
Line 31: | Line 31: | ||
| Internal | | Internal | ||
|- | |- | ||
- | ! Switch | + | ! LAN / WAN Switch Ports |
- | | | + | | 4/1 (10/100 Mb/s) |
|- | |- | ||
! USB Port | ! USB Port | ||
Line 39: | Line 39: | ||
- | = Flashing Instructions = | + | =Flashing Instructions= |
+ | After using the initial flash trailed build (the file with the router name in it), '''only use nv64k builds to upgrade''' with or you will brick your unit. Don't confuse this unit with some other Linksys E-Series units that use nv60k builds! | ||
- | + | ===Initial Flash=== | |
- | + | #Read the [[Firmware_FAQ]] and [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 '''Peacock Announcement''']. | |
- | # Read the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 '''Peacock Announcement'''] | + | #Connect a LAN cable to the PC doing the flash, and disconnect other cables and wireless clients |
- | # | + | #Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 hard] reset on router |
- | # Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 | + | #Log into [http://192.168.1.1 Linksys Web Interface] Firmware Upgrade page |
- | + | #Upload the known good initial flash [ftp://ftp.dd-wrt.com/betas/2013/05-27-2013-r21676/broadcom_K26/dd-wrt.v24-21676_NEWD-2_K2.6_mini-e1200v1.bin '''E1200 (v1) Trailed Build'''] | |
- | # Log into | + | #Wait 5 minutes to assure flash integrity, then power cycle the E1200 (unplug for 10 seconds). |
- | # Wait 5 minutes to assure flash integrity | + | #Plug the E1200 back in and wait about 2 minutes until it finishes booting. |
- | + | #Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 hard] reset, then wait for it to boot. | |
- | # Plug the E1200 back in and wait about 2 minutes until it finishes booting. | + | #Open web interface to set a user and password, then configure as needed. |
- | # Do a [http://www.dd-wrt.com/wiki/index.php/Hard_reset_or_30/30/30 | + | |
- | # | + | |
- | + | ||
- | + | ||
- | + | ||
+ | ===Upgrade DD-WRT=== | ||
+ | #To upgrade, use a k2.6 nv64k mini build (''_K2.6_mini-nv64k.bin'') from the /broadcom_K26 directory. | ||
+ | #Research build threads first to avoid bad builds. | ||
+ | *'''WARNING:''' only use nv64k builds that fit a 4MB flash footprint, bigger builds can either fail or brick your unit. | ||
+ | *'''Do not try to flash K3X:''' while a K3X trailed and nv64k build exists, the files are for minimum 8MB flash devices. | ||
=Build Information= | =Build Information= | ||
+ | '''Support for this model was added with build 18946, so do not use any older builds.''' To be safe, only use builds that are linked within this wiki, or otherwise read New Build and model-specific [https://www.dd-wrt.com/phpBB2/viewforum.php?f=1 forum threads]. To find the latest builds, look [ftp://ftp.dd-wrt.com/betas/ here] in broadcom_K26 folders. | ||
- | '''As noted in bold at the beginning of the flashing instructions, only use builds with nv64k in the name for upgrading - otherwise follow the initial flash instructions above if you are going from stock to dd-wrt, any other builds for upgrading an existing dd-wrt install without nv64k in the name will brick your router! This unit was supported with build 18946 or greater, this means you cannot use a build with a number lesser than 18946. For the safest results, use builds that are linked within this wiki as they have most likely been forum tested with ok reported results.''' | ||
- | |||
- | To find the latest builds, you can browse the DD-WRT file server and look for the broadcom_K26 folder, in there is the appropriate for your unit. '''Be aware that these are beta test builds and should be used with caution!''' | ||
- | |||
- | ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2 | ||
+ | =More Information= | ||
+ | '''Forum thread''': [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=153302 for early E-Series] routers. | ||
=Reverting to Stock Firmware= | =Reverting to Stock Firmware= | ||
+ | Download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1 | ||
- | + | [[Category:Linksys]] |
Revision as of 17:33, 24 January 2019
This page applies to version 1. For version 2, see Linksys E1200v2
Contents |
Hardware Information
CPU | Broadcom BCM5357 |
---|---|
CPU Speed | 300 MHz |
Flash ROM | 4 MB |
RAM | 32 MB |
Radio | 2.4 GHz |
WLAN Support | b/g/n |
WLAN Max Speed | 300 mbps |
Antenna Location | Internal |
LAN / WAN Switch Ports | 4/1 (10/100 Mb/s) |
USB Port | None |
Flashing Instructions
After using the initial flash trailed build (the file with the router name in it), only use nv64k builds to upgrade with or you will brick your unit. Don't confuse this unit with some other Linksys E-Series units that use nv60k builds!
Initial Flash
- Read the Firmware_FAQ and Peacock Announcement.
- Connect a LAN cable to the PC doing the flash, and disconnect other cables and wireless clients
- Do a hard reset on router
- Log into Linksys Web Interface Firmware Upgrade page
- Upload the known good initial flash E1200 (v1) Trailed Build
- Wait 5 minutes to assure flash integrity, then power cycle the E1200 (unplug for 10 seconds).
- Plug the E1200 back in and wait about 2 minutes until it finishes booting.
- Do a hard reset, then wait for it to boot.
- Open web interface to set a user and password, then configure as needed.
Upgrade DD-WRT
- To upgrade, use a k2.6 nv64k mini build (_K2.6_mini-nv64k.bin) from the /broadcom_K26 directory.
- Research build threads first to avoid bad builds.
- WARNING: only use nv64k builds that fit a 4MB flash footprint, bigger builds can either fail or brick your unit.
- Do not try to flash K3X: while a K3X trailed and nv64k build exists, the files are for minimum 8MB flash devices.
Build Information
Support for this model was added with build 18946, so do not use any older builds. To be safe, only use builds that are linked within this wiki, or otherwise read New Build and model-specific forum threads. To find the latest builds, look here in broadcom_K26 folders.
More Information
Forum thread: for early E-Series routers.
Reverting to Stock Firmware
Download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1