D-Link DIR-400
From DD-WRT Wiki
Revision as of 04:45, 30 September 2009 (edit) DHC DarkShadow (Talk | contribs) (New page: In order to flash your router you need to do the following steps: * Download TFTPserver, it can be downloaded from [http://www.dd-wrt.com/dd-wrtv2/downloads/stable/dd-wrt.v24%20SP1/Consume...) ← Previous diff |
Revision as of 08:58, 30 April 2010 (edit) (undo) Glenn (Talk | contribs) (+cat) Next diff → |
||
Line 99: | Line 99: | ||
Your router will be accessible at http://192.168.1.1 | Your router will be accessible at http://192.168.1.1 | ||
+ | |||
+ | [[Category:D-Link guides]] |
Revision as of 08:58, 30 April 2010
In order to flash your router you need to do the following steps:
- Download TFTPserver, it can be downloaded from here
- Download firmware from here
- Download Putty client or you can use any telnet clients(try to stay away from Windows built in telnet)
- Change your local IP adress to a static 192.168.0.2 and subnet mask to 255.255.255.0
- Connect an ethernet cable between your computer and DIR-400's WAN port
- Prepare Putty telnet session -- 192.168.0.1 port 9000
- Start pinging your router throught a command line. Type ping 192.168.0.1 -n 900 (You don't really need to ping that many times)
- Power DIR-400 router on and wait for 2nd successful ping and then initiate putty telnet session.
- Press CTRL-C as soon as you see that boot script is executing (if you are using Putty ver. 0.60 or newer then you don't have to worry about this)
- Start TFTP server with linux.bin in TFTP root directory
If you did everything right then you should see the following on the window of putty:
== Executing boot script in 1.140 seconds - enter ^C to abort ^C RedBoot>
Type ip_address -l 192.168.0.1/24 -h 192.168.0.2 and press Enter
You should see the following:
RedBoot> ip_address -l 192.168.0.1/24 -h 192.168.0.2 IP: 192.168.0.1/255.255.255.0, Gateway: 0.0.0.0 Default server: 192.168.0.2
Type fis init and then
RedBoot> fis init About to initialize [format] FLASH image system - continue (y/n)?
Type y and press Enter. Wait until the process is complete:
About to initialize [format] FLASH image system - continue (y/n)? y *** Initialize FLASH Image System And a descriptor for the configuration data size = 10000 ... Erase from 0xbffe0000-0xbfff0000: . ... Program from 0x80ff0000-0x81000000 at 0xbffe0000: .
Type load -r -b 0x80041000 linux.bin and press Enter
RedBoot> load -r -b 0x80041000 linux.bin Using default protocol (TFTP) Raw file loaded 0x80041000-0x803bafff, assumed entry at 0x80041000
Type fis create linux and press Enter (this one will take a while. DO NOT UNPLUG YOUR ROUTER)
RedBoot> fis create linux ... Erase from 0xbfc40000-0xbffba000: ........................................................ ... Program from 0x80041000-0x803bb000 at 0xbfc40000: ........................................................ prog_ok flash_addr = 0xbfc40000 mem_addr = 0x80041000 entry_addr = 0x80041000 length = 0x37a000 img_size = 0x37a000 ... Erase from 0xbffe0000-0xbfff0000: . ... Program from 0x80ff0000-0x81000000 at 0xbffe0000: .
Type fconfig and press Enter
RedBoot> fconfig Run script at boot: true
Press Enter
Run script at boot: true Boot script: .. fis load -l linux .. exec Enter script, terminate with empty line
Type fis load -l linux and press Enter
>> fis load -l linux
type exec and press Enter
>> exec
just press Enter
>> Boot script timeout (1000ms resolution): 2
press Enter
Use BOOTP for network configuration: false
press Enter
Gateway IP address:
press Enter
Local IP address: 192.168.0.1
press Enter
Local IP address mask: 255.255.255.0
press Enter
Default server IP address: 192.168.0.100
press Enter
Console baud rate: 9600
press Enter
GDB connection port: 9000
press Enter
Force console for special debug messages: false
press Enter
Network debug at boot time: false
press Enter
Update RedBoot non-volatile configuration - continue (y/n)?
type y and press Enter
Update RedBoot non-volatile configuration - continue (y/n)? y ... Erase from 0xbffe0000-0xbfff0000: . ... Program from 0x80ff0000-0x81000000 at 0xbffe0000: .
Type reset and press Enter
RedBoot> reset
- Re-connect an ethernet cable between your computer and DIR-400’s LAN port
- Change your local IP adress to a static 192.168.1.2 and subnet mask to 255.255.255.0
Your router will be accessible at http://192.168.1.1