Posted: Wed Jul 24, 2013 20:16 Post subject: Which toolchain to compile dd-wrt for this router?
Which toolchain does brainslayer use to compile dd-wrt firmware? The only one I can get to partially work is toolchain-mipsel_gcc-linaro_uClibc-0.9.32. The 4.6 and 4.7 ones for mipsel just give me a libcloog.so error very early on. The one that partially works, toolchain-mipsel_gcc-linaro_uClibc-0.9.32 but randomly fails on several things (iproute2, openssl, sputnik, kernel 3.10).
Joined: 08 Jun 2006 Posts: 35 Location: Santiago, Chile
Posted: Thu Jul 25, 2013 15:52 Post subject:
How is dd-wrt better than ASUS firmware?
(BTW,I posted this as a separate thread, but I got no comments, that's why I'm posting here)
Don't take me wrong, I love DD-WRT and I've used it for over 9 years on my previous router, the good'ol Linksys WRT54GL. However, the benefits of open source firmware seem more distant on this case, as ASUS's firmware is open source as well. At least you can download the source code.
I'm not an expert in this field, so if this "open sourceness" from ASUS is not what it seems, I can't tell.
Besides the license, which is important to me, are there tangible performance benefits or problems I should be aware of regarding both firmwares?
First time post but longtime DDWRT user here with a head scratcher...
Have a new RT-N66U-B1 and flashed dd-wrt.v24-21676_NEWD-2_K3.x_mega_RT-N66U.trx which is working great except that I seem to have slow LAN-LAN throughput (~15Mbps). My NICS are all set for 100Mbps/Full and I have the two laptops with CAT5 (not CAT5e). The cable wirings have been checked and even replaced with cables that came with the Router. If I test LAN-WAN it's as expected (10Mbps Down, 1.5Mbps Up). I haven't messed with the default setup for routing and services so i'm at a loss to understand what i'm doing wrong. My previous was a WRT54G and all was good.
Have a new RT-N66U-B1 and flashed dd-wrt.v24-21676_NEWD-2_K3.x_mega_RT-N66U.trx which is working great except that I seem to have slow LAN-LAN throughput (~15Mbps)....
Mea Culpa here...
I didn't realize that Gig ports don't play well with 100BaseT ports. By going to Setup->Vlans and disabling Auto-Negotiate & Gigabit I was able to get the ports screaming at ~130Mbps (i'll get real gig ports one day)
I've since upgraded to 22118 and it's working great.
Have a new RT-N66U-B1 and flashed dd-wrt.v24-21676_NEWD-2_K3.x_mega_RT-N66U.trx which is working great except that I seem to have slow LAN-LAN throughput (~15Mbps)....
Mea Culpa here...
I didn't realize that Gig ports don't play well with 100BaseT ports. By going to Setup->Vlans and disabling Auto-Negotiate & Gigabit I was able to get the ports screaming at ~130Mbps (i'll get real gig ports one day)
I've since upgraded to 22118 and it's working great.
Is this the file that you used?
dd-wrt.v24-22118_NEWD-2_K3.x_mega_RT-N66U.trx
Also do you know what changed from the previous version or where this is documented?
Hmm... I flashed DD-WRT (dd-wrt.v24-22118_NEWD-2_K3.x-big-RT-N66U.trx) from Merlin build.
The LAN ports are dead. I can only access the router via wifi.
I read this issue was reported by a few users but there was no conclusive fix yet.
Anyone knows how to get the LAN ports working?
Hmm... I flashed DD-WRT (dd-wrt.v24-22118_NEWD-2_K3.x-big-RT-N66U.trx) from Merlin build.
The LAN ports are dead. I can only access the router via wifi.
I read this issue was reported by a few users but there was no conclusive fix yet.
Anyone knows how to get the LAN ports working?
Pleaase supply dmesg output after boot.
And output from:
Okay, I've been trying to get DDWRT onto my N66U, but I"m failing miserably. First time I had a weird issue where the lan ports wouldn't work at all, but wireless would (It seemed to flash all the way, and I was easily able to flash it back to the factory).
This time I completely screwed up by leaving my VPN running while flashing. Smart, I know.
I attempted to flash: dd-wrt.v24-1676_NEWD-2_K3.x_mega_RT=n66u.trx
I pretty much ruined it so I went into recovery to flash back to the stock firmware (N66U_3.0.0.4_370.trx (renamed from .bin)). After doing that flash, my router has gone into what I assume to be a boot cycle. Power (and lan # when my computer is plugged in) stays on solid, and about every 10-15 seconds all the lights will flash, go off, then repeat. It's been doing this for 30 minutes now. I can get into the recovery fine, I flashed the NVRAM and did the nvram+commit thing after flashing, but it's still doing it.
What am I doing wrong?
Also as a side note for my next attempt, using putty to flash the NVRAM, I used mtd-erase -d nvram and reboot to clear then reboot between each flashing.
Addendum: I'm back to when things were doing weird things the first time. I can access the recovery, the wireless works just fine, I can log into the router via wireless, but I cannot use a LAN connection. My PC shows I have a connection with no internet, but it won't ping 192.168.1.1, nor will it load the GUI in the browser, yet my laptop can do both fine. What am I missing, am I flashing the wrong files to start?
When you flashed with DD-WRT, after connecting with WiFi did it misidentify the device as a WRT54GL?
Are your LAN ports unresponsive?
I had the same issue, even after rolling back to stock (LAN ports work again) then reflashing with DD-WRT (LAN ports stopped working).
I eventually solved this by dropping Tomato (tomato-K26USB-1.28.RT-N5x-MIPSR2-110-Mega-VPN-64K) on it first, using the Asus Firmware recovery tool (it will refuse to do it via web interface) and then installing DD-WRT.
LAN ports worked thereafter and device is identified correctly.
Give it a shot and tell me if it works.
I got the tomato build to run. How do I go about flashing dd-wrt after that? Do I just use the gui in the tomato build? Clear nvram before and after?
Hmm... I flashed DD-WRT (dd-wrt.v24-22118_NEWD-2_K3.x-big-RT-N66U.trx) from Merlin build.
The LAN ports are dead. I can only access the router via wifi.
I read this issue was reported by a few users but there was no conclusive fix yet.
Anyone knows how to get the LAN ports working?
Pleaase supply dmesg output after boot.
And output from: