Tenda W150M Protable AP

Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware
Author Message
ssgyk
DD-WRT Novice


Joined: 24 Jul 2010
Posts: 2

PostPosted: Fri Aug 06, 2010 11:14    Post subject: Tenda W150M Protable AP Reply with quote
Hi all,look what I found. A portable AP.
CPU: Ralink RT3050F
RAM: 16MB
ROM: 2MB
Which version of DD-WRT can run on this device.

Photo:
http://220.196.58.193/01.jpg

http://220.196.58.193/02.jpg

http://220.196.58.193/03.jpg


if you cannot see the picture,plz refresh this page.

http://www.tenda.cn/product/show.php?productid-371.html





U-Boot 1.1.3 (Oct 13 2009 - 15:58:57)

Board: Ralink APSoC DRAM: 16 MB
relocate_code Pointer at: 80fb0000
flash_protect ON: from 0xBF000000 to 0xBF01D677
flash_protect ON: from 0xBF030000 to 0xBF030FFF
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.3
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 128 Mbits SDR
DRAM bus: 16 bit
Total memory: 16 MBytes
Flash component: NOR Flash
Date:Oct 13 2009 Time:15:58:57
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 320 MHZ ####

SDRAM bus set to 16 bit
SDRAM size =16 Mbytes
--->Set rt305x Gpio falsh, added by luowl for w150m, 20091014
...................................

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
 0

3: System Boot system code via Flash.
## Booting image at bf050000 ...
Image Name: W150M_16MB_2MB Kernel Image
Created: 2010-01-04 14:13:54 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1730546 Bytes = 1.7 MB
Load Address: 80000000
Entry Point: 8028c000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8028c000) ...
## Giving linux memsize in MB, 16

Starting kernel ...


LINUX started...

THIS IS ASIC

init started: BusyBox v1.12.1 (2010-01-04 01:04:30 CST)

starting pid 10, tty '': '/etc_ro/rcS'
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\

=System Architecture Department=



Yes:

****** WeLoveLinux ******

Welcome to ...
httpd Reg gpio hook success .

starting pid 18, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2010-01-04 01:04:30 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# getIfLive: device eth2.1 not found.
Commit crc = b34d358
maclist:
WLan[C8:3A:35:F4:22:A8]
Lan[C8:3A:35:F4:22:A8]
Wan[C8:3A:35:F4:22:ad]
getIfLive: device br0 not found.
Router ip address config success.
winsTask start...
TendaLog -> ok rtn.
httpd listen ip = 172.18.1.100 port = 80
MfgThread start loop.
TendaLog -> ok rtn.
ifconf
/bin/sh: ifconf: not found
#
# ifconfig
apcli0 Link encap:Ethernet HWaddr C8:3A:35:F4:22:A9
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

br0 Link encap:Ethernet HWaddr C8:3A:35:F4:22:A8
inet addr:172.18.1.100 Bcast:172.18.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:126 (126.0 B)

eth2 Link encap:Ethernet HWaddr C8:3A:35:F4:22:A8
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:384 (384.0 B)
Interrupt:3

eth2.1 Link encap:Ethernet HWaddr C8:3A:35:F4:22:A8
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:138 (138.0 B)

eth2.2 Link encap:Ethernet HWaddr C8:3A:35:F4:22:A8
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:138 (138.0 B)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:90 (90.0 B) TX bytes:90 (90.0 B)

ra0 Link encap:Ethernet HWaddr C8:3A:35:F4:22:A8
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:220 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:38023 (37.1 KiB) TX bytes:693 (693.0 B)
Interrupt:4

#
Sponsor
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17619
Location: Hesse/Germany

PostPosted: Fri Aug 06, 2010 12:03    Post subject: Reply with quote
no support for 2mb flash
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
ssgyk
DD-WRT Novice


Joined: 24 Jul 2010
Posts: 2

PostPosted: Sat Aug 07, 2010 9:39    Post subject: Reply with quote
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800000 ...
Image Name: DD-WRT v24 Linux Kernel Image
Created: 2010-04-16 7:57:12 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 866675 Bytes = 846.4 kB
Load Address: 80000000
Entry Point: 8026d000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8026d000) ...
## Giving linux memsize in MB, 16

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #2591 Fri Apr 16 09:55:31 CEST 2010

The CPU frequency set to 320 MHz
16M RAM Detected!
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists in Zone order. Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 10800020, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 0030d400(3200000)
CPU frequency 320.00 MHz
Using 160.000 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13236k/16384k available (2161k kernel code, 3148k reserved, 318k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
Load RT2880 Timer Module(Wdg/Soft)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
rt3052 access driver initialization.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00050000-0x00120000 : "linux"
0x00120000-0x00200000 : "rootfs"
0x003f0000-0x00400000 : "nvram"
mtd: partition "nvram" is out of reach -- disabled
Trap instruction in kernel code[#1]:
Cpu 0
$ 0 : 00000000 0000002e 00000000 803f0390
$ 4 : 00000000 00000c00 803f0380 00200000
$ 8 : 00000000 00000000 00000000 00000004
$12 : 80290000 80290000 4bb2a980 00000000
$16 : 8039f080 00000000 80368680 8025f2d8
$20 : 00000005 00400000 00000006 80260000
$24 : 8032bd58 0098963a
$28 : 8032a000 8032bed0 00010000 80125dcc
Hi : 00000000
Lo : ffffffff
epc : 80125cd8 Not tainted
ra : 80125dcc Status: 1100fc03 KERNEL EXL IE
Cause : 10800034
PrId : 0001964c
Modules linked in:
Process swapper (pid: 1, threadinfo=8032a000, task=80329878)
Stack : 00000004 80239030 00000001 00200000 80260000 00000000 c1001000 001f0000
00000004 8032bf28 74717368 802e0000 802808b0 802808a0 bf000000 01000000
00000400 00000000 00000004 8032bf28 c1001000 80c82380 00000004 80127b9c
00000000 00000000 00000000 80288d24 00000000 80280000 00000000 00000000
80280000 8026d83c 00000000 8026d77c 00000000 00000000 00000000 00000000
...
Call Trace:[<802808b0>][<802808a0>][<80127b9c>][<80280000>][<80280000>][<8026d83c>][<8026d77c>][<80003c54>][<80003c44>]

Code: 8e0200bc 8e04000c 0044001b <008001f4> 00001810 14600067 2402fbff 8e020008 0044001b
Kernel panic - not syncing: Attempted to kill init!
Rebooting in 1 seconds..
sunny_jerry
DD-WRT Novice


Joined: 25 Oct 2010
Posts: 3

PostPosted: Fri Oct 29, 2010 10:47    Post subject: Reply with quote
Emm....I have a question....
If I upgrade the flash to 4MB and upgrade RAM to 32MB,Can I use DIR-412 OR DIR-600 firmware flash my router?
xll
DD-WRT Novice


Joined: 21 Mar 2011
Posts: 18

PostPosted: Fri May 13, 2011 2:52    Post subject: Reply with quote
sunny_jerry wrote:
Emm....I have a question....
If I upgrade the flash to 4MB and upgrade RAM to 32MB,Can I use DIR-412 OR DIR-600 firmware flash my router?


probablly also need update the Uboot code Embarassed
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum