Joined: 05 Dec 2009 Posts: 377 Location: Toronto, Canada
Posted: Mon Jul 19, 2010 15:13 Post subject:
buddee wrote:
got_milk wrote:
UPnP appears to be broken in this build. Jumped from 14686 (if I recall correctly... ) and while the service is enabled the list remains empty and ports are not opening and closing as they should. First build in a long time I've had UPnP issues.
Seems to be working fine for me using mini-usb-ftp
I have updated my 610n v1 and 610n v2 with "big - build 14826M NEWD-2 K2.6 Eko"
The one thing I do notice is that if I do a power cycle the router doesn't boot fully if a USB flash drive is populated during boot.
I remove the drive and power cycle twice more and the router boots fully and then I insert the USB drive and the router see's it and auto mounts without issue.
Running 23hrs;
Incoming (MBytes) - 2719
Outgoing (MBytes) - 3424
After moving almost 6GB WAN-LAN
I have this to report;
wl0 - wl0 radio worked without issue and performance was 22Mbps each way with G and I was getting 80-85Mbps from the N mode. Both tested conducted using a wired laptop to a single wifi client both clients are Dell d630 laptops with Intel 4965AGN on 64 Win7. I didn't test A band.
wl1 - untested.
Router SERVICES
VPN- PPTP Server - tested and working great with WinXp PPTP native clients connected.
USB storage - tested with both ext3 and a FAT USB flash drives with automount to /opt and they worked without issue for over 24hrs.
WEBGUI is a flaky experience in Firefox 3.6 and flawless in IE8. (WinSrv2008 32bit /Win7 64bit)
-remote admin with HTTPS works without issue.
-UPnP worked the entire time supporting connections for multi GB torrents.
-I have 5 port forwards static NATS configured to multiple computers without issue.
-CIFS clients are configured in WEBGUI and connected to 700GB windows server 2008 share and works without issue.
-JFFS2 enabled and operational without issue.
-DDNS is configured for dyndns and works without issue.
-NTP client is configured on both and works without issue. _________________ Location (urban) - 1x Linksys EA8500 (AP wlan0 & wlan1 enabled)
1x Asus 68u (Repeater Bridge w/VAP) - wl0 disabled
1x Asus 87u (Client Bridge) - wl1 disabled
Finally broke down and flashed this build on my E3000. It's been up for about 14 hours now and running flawlessly. Nothing to report other than that. Good job Eko.
i have 6 WNDR3300's on 14583 NewD-2 std-nokaid_nohotspot_nostor
cuz the newer wireless drivers are so much better,
i sacrificed having dual radios & bought extra routers to act as wireless adapters
2 questions:
can anyone point me to what changes were made for 14826, from 14583
. . . everyone asks "is it worth upgrading"?
and 2nd to a Guru/Eko/BS: if both radios work in every K26 build
for WNDR3300, how come the same NEWD-2 driver doesn't load both radio in the K24 build?
&now 2 routers just broke in the middle of switching frequencies, PREVIOUS build
30/30/30 reset brought them back which is good cuz i could not ping
which brings enough reason to upgrade EVERYTHING,lol
this build is great, after 1 day uptime my wireless error is 9 RX 19 TX. previous build give me hundreds of tx error. _________________ dd-wrt.v24-16754_NEWD-2_K2.6_mini_RT-N12.trx
i have 6 WNDR3300's on 14583 NewD-2 std-nokaid_nohotspot_nostor
cuz the newer wireless drivers are so much better,
i sacrificed having dual radios & bought extra routers to act as wireless adapters
2 questions:
can anyone point me to what changes were made for 14826, from 14583
. . . everyone asks "is it worth upgrading"?
and 2nd to a Guru/Eko/BS: if both radios work in every K26 build
for WNDR3300, how come the same NEWD-2 driver doesn't load both radio in the K24 build?
worth upgrading for me. _________________ dd-wrt.v24-16754_NEWD-2_K2.6_mini_RT-N12.trx
I try print on this firmware on asus rt-n16 on HP photosmart 7150.
before the old firmware which was not supporting printer, print only 5 cm. Now I print the all page ,but without ink. Where is the problem? _________________ RT-N16 back to asus firmware - dd-wrt is very unstable for this router with atheros clients
Posted: Wed Jul 21, 2010 1:39 Post subject: ip6tables
Eko,
Any chance you could compile/post the ip6tables kernel module for this K26 build? I haven't been able to track one down that loads and would really prefer to not build an entire cross compile kernel build system just for this one kernel module.
I see increased wireless speed in the 40mhz modes with my wnr834bv2.
I was able to get 60mbps now, what is okay for this router ( with the older builds the max speed was 40mbps ).
Nothing negative to report yet... _________________ Netgear WNR834B v2 - Eko build v24-sp2 15943M mini NEWD K2.4 (running MINIUPNPD)
Tested with BS 15943 mini build with my 32/1 line over wireless:
) and while the service is enabled the list remains empty and ports are not opening and closing as they should. First build in a long time I've had UPnP issues.
