v.24 sp2 - build 13908 - Airlink ar690w

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2, 3  Next
Author Message
d3hilton
DD-WRT Novice


Joined: 18 Feb 2010
Posts: 40

PostPosted: Wed May 19, 2010 16:06    Post subject: Serial output trying to put Edimax Firmware on the AR690W Reply with quote
So the Edimax firmware does upload, but enters into a reboot cycle to to a LZMA size error




U-Boot 1.1.3 (Mar 27 2008 - 14:57:11) Build 001

Board: RT2880 DRAM: 32 MB
twe0 set to <NULL>
toe0 set to <NULL>
Set up sector start address BC400000
*** Warning - bad CRC, using default environment

============================================
ASIC -VerB/C (MAC to MAC Mode)
DRAM COMPONENT=256Mbits
DRAM BUS=16BIT
Total memory = 32Mbytes
Date:Mar 27 2008 Time:14:57:11
============================================
th0 (10/100-M)

Hit any key to stop autoboot: 0
## Booting image at bc440000 ...
Image Name: 7zip Linux Kernel
Created: 1970-01-01 0:00:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: -1 Bytes = 4096 MB
Load Address: 8a000000
Entry Point: 8a000000
Uncompressing Kernel Image with LZMA ... too long file.
LZMA ERROR - must RESET board to recover !!

_________________
DD-WRT 24-sp2
Current:
Linksys wrt610n v2
Netgear wndr3300
Airlink101 AR690W
Linksys WRT-350N
Linksys WRT54g v8

Past routers
Netgear WPN834bV2
Airlink101 AR670W
Linksys WRE54g

Non DD-WRT
TRENDnet TEW639gr, TEW638, TEW637ap
Sponsor
btechnet
DD-WRT User


Joined: 16 Sep 2009
Posts: 181
Location: USA

PostPosted: Tue May 25, 2010 16:31    Post subject: Reply with quote
Look like BS has the ar690W on the latest list for firmwares!! YAY

heres the link
http://www.dd-wrt.com/dd-wrtv2/down.php?path=downloads%2Fothers%2Feko%2FBrainSlayer-V24-preSP2%2F05-25-10-r14573%2F

_________________
1x WRT610Nv2 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WNDR3300 mini - 14205M NEWD-2 K2.6 Eko
2x AR670w std - 14289 v24
Brainslayer
1x AR690w mini - 15649 v24
Brainslayer
2x AR430W std - 13064 v24 Brainslayer
2x WNR834B v2 mini - 14311 K2.4 BrainSlayer
1x RT-N16 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WRT54G V5.0 micro - 15704 v24 Brainslayer
1x WRT54GL V1.1 micro - 15704 v24 Brainslayer
btechnet
DD-WRT User


Joined: 16 Sep 2009
Posts: 181
Location: USA

PostPosted: Wed May 26, 2010 13:55    Post subject: Reply with quote
tried the 690w firmware that BS just made (14473) the switch doesn't work. Im working on getting the switch driver loaded on boot up, but i need the driver anybody have it?
_________________
1x WRT610Nv2 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WNDR3300 mini - 14205M NEWD-2 K2.6 Eko
2x AR670w std - 14289 v24
Brainslayer
1x AR690w mini - 15649 v24
Brainslayer
2x AR430W std - 13064 v24 Brainslayer
2x WNR834B v2 mini - 14311 K2.4 BrainSlayer
1x RT-N16 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WRT54G V5.0 micro - 15704 v24 Brainslayer
1x WRT54GL V1.1 micro - 15704 v24 Brainslayer
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7631

PostPosted: Wed May 26, 2010 14:31    Post subject: Reply with quote
btechnet wrote:
tried the 690w firmware that BS just made (14473) the switch doesn't work. Im working on getting the switch driver loaded on boot up, but i need the driver anybody have it?


Which driver is loaded by default?

_________________
Kernel panic: Aiee, killing interrupt handler!
btechnet
DD-WRT User


Joined: 16 Sep 2009
Posts: 181
Location: USA

PostPosted: Wed May 26, 2010 14:48    Post subject: Reply with quote
rtl8366 realtek gigabit driver

btw its a k2.6 kernel (because of the gigabit switch)

_________________
1x WRT610Nv2 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WNDR3300 mini - 14205M NEWD-2 K2.6 Eko
2x AR670w std - 14289 v24
Brainslayer
1x AR690w mini - 15649 v24
Brainslayer
2x AR430W std - 13064 v24 Brainslayer
2x WNR834B v2 mini - 14311 K2.4 BrainSlayer
1x RT-N16 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WRT54G V5.0 micro - 15704 v24 Brainslayer
1x WRT54GL V1.1 micro - 15704 v24 Brainslayer
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7631

PostPosted: Wed May 26, 2010 15:19    Post subject: Reply with quote
hmm, then I don't understand your request.

AR690W has a RTL8366SR switch so how will you be helped with a driver for something that is already included in the build?

_________________
Kernel panic: Aiee, killing interrupt handler!
btechnet
DD-WRT User


Joined: 16 Sep 2009
Posts: 181
Location: USA

PostPosted: Wed May 26, 2010 15:52    Post subject: Reply with quote
LOM wrote:
hmm, then I don't understand your request.

AR690W has a RTL8366SR switch so how will you be helped with a driver for something that is already included in the build?


Sorry I wasn't clear enough. I guess that what im looking for is an answer as to why the switch doesn't work if the drivers are loaded

_________________
1x WRT610Nv2 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WNDR3300 mini - 14205M NEWD-2 K2.6 Eko
2x AR670w std - 14289 v24
Brainslayer
1x AR690w mini - 15649 v24
Brainslayer
2x AR430W std - 13064 v24 Brainslayer
2x WNR834B v2 mini - 14311 K2.4 BrainSlayer
1x RT-N16 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WRT54G V5.0 micro - 15704 v24 Brainslayer
1x WRT54GL V1.1 micro - 15704 v24 Brainslayer
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7631

PostPosted: Wed May 26, 2010 16:02    Post subject: Reply with quote
You are sure that it is loaded, just not only included?

I think a cat /proc/modules will tell you that.

_________________
Kernel panic: Aiee, killing interrupt handler!
btechnet
DD-WRT User


Joined: 16 Sep 2009
Posts: 181
Location: USA

PostPosted: Wed May 26, 2010 16:11    Post subject: Reply with quote
root@DD-WRT:~# cat /proc/modules
nf_nat_pptp 4096 0 - Live 0x89d4c000
nf_conntrack_pptp 4096 1 nf_nat_pptp, Live 0x894ce000
nf_nat_proto_gre 4096 1 nf_nat_pptp, Live 0x894c2000
nf_conntrack_proto_gre 4096 1 nf_conntrack_pptp, Live 0x89476000
etherip 8192 0 - Live 0x894d4000
rt2860v2_ap 507904 1 - Live 0x89a00000 (P)
root@DD-WRT:~#


doesn't look like its loaded, since im no expert with the file structure, how do i load it?

_________________
1x WRT610Nv2 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WNDR3300 mini - 14205M NEWD-2 K2.6 Eko
2x AR670w std - 14289 v24
Brainslayer
1x AR690w mini - 15649 v24
Brainslayer
2x AR430W std - 13064 v24 Brainslayer
2x WNR834B v2 mini - 14311 K2.4 BrainSlayer
1x RT-N16 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WRT54G V5.0 micro - 15704 v24 Brainslayer
1x WRT54GL V1.1 micro - 15704 v24 Brainslayer
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7631

PostPosted: Wed May 26, 2010 16:33    Post subject: Reply with quote
I checked here and I was wrong, my switch driver doesn't show up in /proc/modules.

My switch driver for a Broadcom based router is located in:

/lib/modules/2.6.24.111/kernel/drivers/net/switch

in my case switch-core.ko and switch-robo.ko , in your case most likely rtl8366.ko

You can do an insmod there of the switch driver if you think it is not loaded.

_________________
Kernel panic: Aiee, killing interrupt handler!
btechnet
DD-WRT User


Joined: 16 Sep 2009
Posts: 181
Location: USA

PostPosted: Wed May 26, 2010 16:42    Post subject: Reply with quote
I don't have the folder /lib/modules/2.6.24.111/kernel/drivers/net/switch

mine is
/lib/modules/2.6.23.17/kernel/drivers/net

there is no switch folder.

what does exists is imq.ko and a folder called wireless

i did a find / -name *.ko and the only thing that showed was imq.ko

i also searched for rtl8366.ko and it doesn't exist.

_________________
1x WRT610Nv2 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WNDR3300 mini - 14205M NEWD-2 K2.6 Eko
2x AR670w std - 14289 v24
Brainslayer
1x AR690w mini - 15649 v24
Brainslayer
2x AR430W std - 13064 v24 Brainslayer
2x WNR834B v2 mini - 14311 K2.4 BrainSlayer
1x RT-N16 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WRT54G V5.0 micro - 15704 v24 Brainslayer
1x WRT54GL V1.1 micro - 15704 v24 Brainslayer
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7631

PostPosted: Wed May 26, 2010 17:31    Post subject: Reply with quote
It is possible that the switch driver is compiled into the kernel.

I did a quick search in the dd-wrt source tree but couldn't find much about the AR690W Shocked

Is it only the LAN ports not working or also the WAN port? Can you connect via wireless?

What is really needed now is a serial log of the boot to see what actually gets loaded and if there are any error messages..

_________________
Kernel panic: Aiee, killing interrupt handler!
btechnet
DD-WRT User


Joined: 16 Sep 2009
Posts: 181
Location: USA

PostPosted: Wed May 26, 2010 17:39    Post subject: Reply with quote
i started a new thread

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=72848

I don't have a serial adaptor or jtag to check. Im working on getting a serial cable

_________________
1x WRT610Nv2 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WNDR3300 mini - 14205M NEWD-2 K2.6 Eko
2x AR670w std - 14289 v24
Brainslayer
1x AR690w mini - 15649 v24
Brainslayer
2x AR430W std - 13064 v24 Brainslayer
2x WNR834B v2 mini - 14311 K2.4 BrainSlayer
1x RT-N16 big - 14280 NEWD-2 K2.6 BrainSlayer
1x WRT54G V5.0 micro - 15704 v24 Brainslayer
1x WRT54GL V1.1 micro - 15704 v24 Brainslayer
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7631

PostPosted: Wed May 26, 2010 18:17    Post subject: Reply with quote
btechnet wrote:

I don't have a serial adaptor or jtag to check. Im working on getting a serial cable


A serial cable is a must for you in order to provide enough information to the developers, it is also useful in 95% of all brick cases.

jtag is mainly useful for debricking when the boot loader has got overwritten but those cases are rare.
jtag doesn't give you any debug info from the boot, is not a fault finding tool.

_________________
Kernel panic: Aiee, killing interrupt handler!
d3hilton
DD-WRT Novice


Joined: 18 Feb 2010
Posts: 40

PostPosted: Thu May 27, 2010 0:14    Post subject: Serial Log Reply with quote
U-Boot 1.1.3 (Mar 27 2008 - 14:57:11) Build 001

Board: RT2880 DRAM: 32 MB
twe0 set to <NULL>
toe0 set to <NULL>
Set up sector start address BC400000
*** Warning - bad CRC, using default environment

============================================
ASIC -VerB/C (MAC to MAC Mode)
DRAM COMPONENT=256Mbits
DRAM BUS=16BIT
Total memory = 32Mbytes
Date:Mar 27 2008 Time:14:57:11
============================================

Eth0 (10/100-M)



Hit any key to stop autoboot: 0
## Booting image at bc440000 ...
Image Name: 7zip Linux Kernel
Created: 1970-01-01 0:00:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: -1 Bytes = 4096 MB
Load Address: 8a000000
Entry Point: 8a000000
Uncompressing Kernel Image with LZMA ... OK

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #2936 Tue May 25 08:56:34 CEST 2010

The CPU frequency set to 266 MHz
32M RAM Detected!
CPU revision is: 0001906c
Determined physical RAM map:
memory: 02000000 @ 08000000 (usable)
Wasting 1048576 bytes for tracking 32768 unused pages
Built 1 zonelists in Zone order. Total pages: 40640
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
cause = 3080005c, status = 1000ff00
PID hash table entries: 1024 (order: 10, 4096 bytes)
calculating r4koff... 0028b0aa(2666666)
CPU frequency 266.67 MHz
Using 133.333 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 28032k/32768k available (2345k kernel code, 4672k reserved, 318k data, 124k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
Load RT2880 Timer Module(Wdg/Soft)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xa0300500 (irq = 9) is a 16550A
serial8250: ttyS1 at I/O 0xa0300c00 (irq = Cool is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x400000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

found squashfs at 118000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00040000-0x003f0000 : "linux"
0x00118000-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
IPP2P v0.8.2 loading
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00 256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
GDMA1_MAC_ADRH -- : 0x0000fb47
GDMA1_MAC_ADRL -- : 0x9d6b785d
PROC INIT OK!
Rtl8366 Phy Init...<0>decode /dev/mtdblock4
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 124k freed
start service
starting Architecture code for rt2880
rt2860v2_ap: module license 'unspecified' taints kernel.
GDMA1_MAC_ADRH -- : 0x0000001d
GDMA1_MAC_ADRL -- : 0x6ab83cab

phy_tx_ring = 0x09e7f000, tx_ring = 0xa9e7f000, size: 16 bytes

phy_rx_ring = 0x09db0000, rx_ring = 0xa9db0000, size: 16 bytes
GDMA1_FWD_CFG = 10000
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device br0 entered promiscuous mode
Algorithmics/MIPS FPU Emulator v1.5
device vlan1 entered promiscuous mode
device eth2 entered promiscuous mode
device vlan2 entered promiscuous mode
sh: ead: not found
RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
0x1300 = 00064380
device ra0 entered promiscuous mode
device apcli0 entered promiscuous mode
device ra1 entered promiscuous mode
br0: port 5(ra1) entering learning state
br0: port 4(apcli0) entering learning state
br0: port 3(ra0) entering learning state
br0: port 2(vlan2) entering learning state
br0: port 1(vlan1) entering learning state
device br0 left promiscuous mode
device br0 entered promiscuous mode
device br0 left promiscuous mode
device br0 entered promiscuous mode
wland: No such file or directory
br0: topology change detected, propagating
br0: port 5(ra1) entering forwarding state
br0: topology change detected, propagating
br0: port 4(apcli0) entering forwarding state
br0: topology change detected, propagating
br0: port 3(ra0) entering forwarding state
br0: topology change detected, propagating
br0: port 2(vlan2) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
etherip: Ethernet over IPv4 tunneling driver
Bad argument `23'

DD-WRT v24-sp2 std (c) 2010 NewMedia-NET GmbH
Release: 05/25/10 (SVN revision: 14473)
ÿ
DD-WRT login:

_________________
DD-WRT 24-sp2
Current:
Linksys wrt610n v2
Netgear wndr3300
Airlink101 AR690W
Linksys WRT-350N
Linksys WRT54g v8

Past routers
Netgear WPN834bV2
Airlink101 AR670W
Linksys WRE54g

Non DD-WRT
TRENDnet TEW639gr, TEW638, TEW637ap
Goto page Previous  1, 2, 3  Next Display posts from previous:    Page 2 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum