TENDA W311R - Bad flash recover and Install dd-wrt firmware!

Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2, 3 ... , 21, 22, 23  Next
Author Message
reluare
DD-WRT Novice


Joined: 01 Sep 2013
Posts: 13

PostPosted: Mon Sep 09, 2013 15:47    Post subject: Reply with quote
Post was complete, I waited 10 minutes and never showed anything but what I wrote above, then I tried to start with the reset button pressed, the only difference was that I showed at one time message that is waiting to release reset button, then continued as in the post above, here is the complete log that appeared when I started with the reset button pressed and then I released seeing the message that is waiting to release the reset button



""""Decompressing...done


CFE version 5.100.138.3 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 2011-05-26 10:33:50 4 (richard@aeteam.com)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.3
CPU type 0x19749: 300MHz
Tot mem: 8192 KBytes

CFE mem: 0x80700000 - 0x80798550 (623952)
Data: 0x8072E3A0 - 0x807315C0 (12832)
BSS: 0x807315C0 - 0x80732550 (3984)
Heap: 0x80732550 - 0x80796550 (409600)
Stack: 0x80796550 - 0x80798550 (8192)
Text: 0x80700000 - 0x8072E39C (189340)

Committing NVRAM...done
Waiting for reset button release...doneÍDecompressing...done


CFE version 5.100.138.3 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 2011-05-26 10:33:50 4 (richard@aeteam.com)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.3
CPU type 0x19749: 300MHz
Tot mem: 8192 KBytes

CFE mem: 0x80700000 - 0x80798550 (623952)
Data: 0x8072E3A0 - 0x807315C0 (12832)
BSS: 0x807315C0 - 0x80732550 (3984)
Heap: 0x80732550 - 0x80796550 (409600)
Stack: 0x80796550 - 0x80798550 (8192)
Text: 0x80700000 - 0x8072E39C (189340)

Device eth0: hwaddr C8-3A-35-07-20-D0, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .... 2168216 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
"""""
after this nothing is going on
Sponsor
reluare
DD-WRT Novice


Joined: 01 Sep 2013
Posts: 13

PostPosted: Mon Sep 09, 2013 18:31    Post subject: Reply with quote
I DID IT !!!
Very Happy
Boot sequence stops with the command Ctrl + C, at which the router begins to respond to ping. I then tried to use a TFTP server to upload the firmware but it did not work. Trying to access the web interface I had the pleasant surprise to see that there is an interface that allows me to upload firmware directly from there. Thanks to all who participated with ideas and tips


Last edited by reluare on Sun Sep 22, 2013 15:15; edited 1 time in total
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Tue Sep 10, 2013 18:29    Post subject: Reply with quote
reluare wrote:
I DID IT !!!
Very Happy
Boot sequence stops with the command Ctrl + C, at which the router begins to respond to ping. I then tried to use a TFTP server to upload the firmware but it did not work. Trying to access the web interface I had the pleasant surprise to see that there is an interface that allows me to upload firmware directly from there. I come back with a mini tutorial for this model in the hope that it will be useful to anyone else. Thanks to all who participated with ideas and tips


YEAH !
Please upload image of soldering work. Thanks !
reluare
DD-WRT Novice


Joined: 01 Sep 2013
Posts: 13

PostPosted: Wed Sep 11, 2013 21:27    Post subject: TendaW311R+ rx tx broadcom chipset , board v 2.0 Reply with quote
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command , after acces emergency boot room via web on 192.168.1.1 (broadcom mini web server)
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Thu Sep 12, 2013 18:13    Post subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0 Reply with quote
reluare wrote:
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command , after acces emergency boot room via web on 192.168.1.1 (broadcom mini web server)


maybe there is a way to stop boot process without using serial connection. I mean some procedure with qss/reset button ?

what did you use to connect metal parts to pcb ?
reluare
DD-WRT Novice


Joined: 01 Sep 2013
Posts: 13

PostPosted: Fri Sep 13, 2013 15:24    Post subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0 Reply with quote
TendaW311R+ wrote:
reluare wrote:
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command , after acces emergency boot room via web on 192.168.1.1 (broadcom mini web server)


maybe there is a way to stop boot process without using serial connection. I mean some procedure with qss/reset button ?

what did you use to connect metal parts to pcb ?



I used solder soldering. I tried all sorts of combinations with the reset button, but no effect.
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Fri Sep 13, 2013 15:49    Post subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0 Reply with quote
reluare wrote:
TendaW311R+ wrote:
reluare wrote:
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command , after acces emergency boot room via web on 192.168.1.1 (broadcom mini web server)


maybe there is a way to stop boot process without using serial connection. I mean some procedure with qss/reset button ?

what did you use to connect metal parts to pcb ?



I used solder soldering. I tried all sorts of combinations with the reset button, but no effect.


I asked you because the pcb looks burnt and there is a connection between TX and RX - that looks for me
reluare
DD-WRT Novice


Joined: 01 Sep 2013
Posts: 13

PostPosted: Fri Sep 13, 2013 22:02    Post subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0 Reply with quote
TendaW311R+ wrote:
reluare wrote:
TendaW311R+ wrote:
reluare wrote:
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command , after acces emergency boot room via web on 192.168.1.1 (broadcom mini web server)


maybe there is a way to stop boot process without using serial connection. I mean some procedure with qss/reset button ?

what did you use to connect metal parts to pcb ?



I used solder soldering. I tried all sorts of combinations with the reset button, but no effect.


I asked you because the pcb looks burnt and there is a connection between TX and RX - that looks for me


I used something besides solder, rosin, to prevent solder to join the two points that are very close. because of rosin the PCB looks like it is burned
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Sep 14, 2013 8:18    Post subject: Reply with quote
Clearly. Thanks for image and replay Very Happy. Is it possible to damage the pins with soldering iron ? I maen to overheat it while solder ?
reluare
DD-WRT Novice


Joined: 01 Sep 2013
Posts: 13

PostPosted: Sat Sep 14, 2013 9:25    Post subject: Reply with quote
TendaW311R+ wrote:
Clearly. Thanks for image and replay Very Happy. Is it possible to damage the pins with soldering iron ? I maen to overheat it while solder ?

The circuit can be easily destroyed if you use a soldering iron that has too much power; is preferable one as small power as possible, or if you have a hot air soldering station, and work carefully as rapidly possible, avoiding to keep the soldering on the circuit too much. Also need to use solder that melts at a lower temperature and to be as thin as possible.
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sun Sep 15, 2013 17:45    Post subject: Reply with quote
reluare wrote:
TendaW311R+ wrote:
Clearly. Thanks for image and replay Very Happy. Is it possible to damage the pins with soldering iron ? I maen to overheat it while solder ?

The circuit can be easily destroyed if you use a soldering iron that has too much power; is preferable one as small power as possible, or if you have a hot air soldering station, and work carefully as rapidly possible, avoiding to keep the soldering on the circuit too much. Also need to use solder that melts at a lower temperature and to be as thin as possible.


What kind of soldering iron did you use ? How many watts ?
reluare
DD-WRT Novice


Joined: 01 Sep 2013
Posts: 13

PostPosted: Mon Sep 16, 2013 10:12    Post subject: Reply with quote
TendaW311R+ wrote:
reluare wrote:
TendaW311R+ wrote:
Clearly. Thanks for image and replay Very Happy. Is it possible to damage the pins with soldering iron ? I maen to overheat it while solder ?

The circuit can be easily destroyed if you use a soldering iron that has too much power; is preferable one as small power as possible, or if you have a hot air soldering station, and work carefully as rapidly possible, avoiding to keep the soldering on the circuit too much. Also need to use solder that melts at a lower temperature and to be as thin as possible.


What kind of soldering iron did you use ? How many watts ?

ProsKit , 30W
palino
DD-WRT Novice


Joined: 20 Oct 2014
Posts: 1

PostPosted: Mon Oct 20, 2014 21:43    Post subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0 Reply with quote
reluare wrote:
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command , after acces emergency boot room via web on 192.168.1.1 (broadcom mini web server)

Hi, please, could you tell mi which pin should I use for GND, is it one of TPx pins? or e.g. could I use GND from wifi antenna?
I have W316R and I upgraded with wrong fw, I hope there is a chance to upload correct fw. I wrote to tech support and they told me that the router is totally damaged.
Thanks in advance for help.
reluare
DD-WRT Novice


Joined: 01 Sep 2013
Posts: 13

PostPosted: Mon Oct 20, 2014 21:59    Post subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0 Reply with quote
palino wrote:
reluare wrote:
TP1 = to the Rx port of the serial
TP2 = to the Tx port of the serial

U can use a normal serial conection, no need for level adapter from 3,3v to 5 v

to stop the boot proces use Cntrl+C command , after acces emergency boot room via web on 192.168.1.1 (broadcom mini web server)

Hi, please, could you tell mi which pin should I use for GND, is it one of TPx pins? or e.g. could I use GND from wifi antenna?
I have W316R and I upgraded with wrong fw, I hope there is a chance to upload correct fw. I wrote to tech support and they told me that the router is totally damaged.
Thanks in advance for help.



Hi, u can use the gnd from antena.Good luck
Nikopol2014
DD-WRT Novice


Joined: 26 Nov 2014
Posts: 2

PostPosted: Fri Nov 28, 2014 13:35    Post subject: Re: TendaW311R+ rx tx broadcom chipset , board v 2.0 Reply with quote
reluare wrote:
to stop the boot proces use Cntrl+C command , after acces emergency boot room via web on 192.168.1.1 (broadcom mini web server)

Hi, reluare. I have the same router. I see boot messages but i cant send ctrl+c command. Please help me. When i should send command or maybe my putty parameters wrong?

My log:
Code:
CFE version 5.100.138.3 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 2011-05-26 10:33:50 4 (richard@aeteam.com)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.3
CPU type 0x19749: 300MHz
Tot mem: 8192 KBytes

CFE mem:    0x80700000 - 0x80798550 (623952)
Data:       0x8072E3A0 - 0x807315C0 (12832)
BSS:        0x807315C0 - 0x80732550 (3984)
Heap:       0x80732550 - 0x80796550 (409600)
Stack:      0x80796550 - 0x80798550 (8192)
Text:       0x80700000 - 0x8072E39C (189340)

Committing NVRAM...done
Waiting for reset button release...done▒Decompressing...done


CFE version 5.100.138.3 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 2011-05-26 10:33:50 4 (richard@aeteam.com)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.3
CPU type 0x19749: 300MHz
Tot mem: 8192 KBytes

CFE mem:    0x80700000 - 0x80798550 (623952)
Data:       0x8072E3A0 - 0x807315C0 (12832)
BSS:        0x807315C0 - 0x80732550 (3984)
Heap:       0x80732550 - 0x80796550 (409600)
Stack:      0x80796550 - 0x80798550 (8192)
Text:       0x80700000 - 0x8072E39C (189340)

Device eth0:  hwaddr C8-3A-35-3D-E2-F8, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ..... 2532860 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Goto page Previous  1, 2, 3 ... , 21, 22, 23  Next Display posts from previous:    Page 22 of 23
Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum