Posted: Tue Jun 20, 2006 4:20 Post subject: Help Me! No he Podido Flashar WRT54G v5.0
Hola!
He tratado de Flashar mi WRT54G v5.0, construí éste cable
he verificado que funcione y de hecho creo que si por que me muestra la sgte pantalla
He Realizado los sgtes pasos:
Antes que nada Creo un CFE.BIN con el "Bootloader Creator 2.0" de Skynet
y cambio la direccion IP de mi PC a estatica con los sgtes parametros:
y ademas la configuro como "Force 10 Half duplex" y despues de esto Entro a la linea de Comandos y ejecuto:
1- wrt54g -backup:wholeflash (Lo Realiza)
2- wrt54g -erase:wholeflash /noemw (Lo Realiza)
3- wrt54g -flash:CFE /noreset (Lo Realiza)
4- le quito corriente al router y luego vuelvo a darle
5- hago ping a 192.168.1.245 y y ejecuto el tftp y me aparece esto:
por lo que me doy cuenta en el momento que ejecuto el tftp veo al router parpadear muy rápidamente como si efectivamente recibiera el archivo entonces espero un buen rato (hasta 10 minutos) y nada! solo el led de power parpadeando. le he quitado corriente y vuelto a poner, seguido he ejecutado "wrt54g -erase:nvram /noerase" y lo realiza pero ni así da respuesta....!
Hasta lo he tratado de flasharlo renombrando el "dd-wrt.v23_micro_wrt54g.bin" a KERNEL.BIN y nada! y luego subirlo con "wrt54g -flash:kernel" pero ni señas de vida....
lo he restaurado con la copia anteriormente realizada (wrt54g -flash:wholeflash /noemw) y vuelve a quedar de fabrica funcionando.
Joined: 18 Jun 2006 Posts: 1110 Location: Kiel (54.4247,10.1721)
Posted: Tue Jun 20, 2006 6:53 Post subject:
Although I don't understand everything you were talking about I still recommend you one thing (WITHOUT WARRANTY!):
try the dd-wrt.v23_micro_generic.bin
It worked for me, dunno why but with the dd-wrt.v23_micro_wrt54g.bin I had the same problems and now I have two boxes running, one at home and one at work, the one at home:
Code:
Firmware: DD-WRT v23 SP1 Final (05/16/06) micro
Time: 08:51:52 up 7 days, 22:50, load average: 0.16, 0.03, 0.01
WAN disabled
Hope this helps! And besides: Nice post, much information *g* But next time try the spanish (guess it is spanisch) forum
I did this:
Created CFE.BIN using Skynet "Bootloader Creator 2.0", changed pc ip address to fixed to this:
I also set "Force 10 Half duplex"
Done that, on command line I did:
1- wrt54g -backup:wholeflash (worked ok)
2- wrt54g -erase:wholeflash /noemw (worked ok)
3- wrt54g -flash:CFE /noreset (worked ok)
4- power cicle router and:
5- ping 192.168.1.245, then run tftp:
then router lights blinks showing activity, I guess it successfully loads firmware via tftp, then wait up to 10 mins, just power led blinks.
Also did "wrt54g -erase:nvram /noerase" but nothing.
I also tried renaming wrt.v23_micro_wrt54g.bin" a KERNEL.BIN and flashing that, not response.
Finally I flashed it using the backup image (wrt54g - lash:wholeflash /noemw), it works as new.
Posted: Tue Jun 20, 2006 23:27 Post subject: Al Fin!
Gracias por su recomendaciones!
AL fin pude flaharlo y el problema radicaba que a mi WRT54G V5.0 lo estaba flashando con la version "dd-wrt.v23_micro_wrt54g.bin" y por eso no me booteba...!
Utilizé la versión "dd-wrt.v23_micro_generic.bin" y listo! al fin pude tener en mi linksys el DD-WRT...!