DD-WRT :: View topic - Sitecom WL-342 (rebadged Senao ESR-9752-SC) Support?

Sitecom WL-342 (rebadged Senao ESR-9752-SC) Support?

This topic is locked: you cannot edit posts or make replies.

DD-WRT Forum Index -> Ralink SoC based Hardware

Goto page Previous 1, 2, 3, 4, 5, 6, 7, 8, 9 Next

View previous topic :: View next topic

Author

Message

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 13:41 Post subject:
Ok, managed to do 'erase nvram' before it crashed. I'm now somewhat stable in the console via serial. Will test further to try to determine the cause of the crashes.

Sponsor

BrainSlayer
Site Admin

Joined: 06 Jun 2006
Posts: 7492
Location: Dresden, Germany

Posted: Sun Jul 19, 2009 14:00 Post subject:
i believe the problem is the used bottom flash memory. i had the same problem with a ESR6650 device, the fix was to move the nvram partition from the end to the sector before. let me play with some ideas _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s

BrainSlayer
Site Admin

Joined: 06 Jun 2006
Posts: 7492
Location: Dresden, Germany

Posted: Sun Jul 19, 2009 14:23 Post subject:
please try this uboot image _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 14:48 Post subject:

Unfortunately, no improvements.

Issues noticed sofar

- command 'reboot' in shell causes crash
- changing username/password in webif still causes crash
- the wan-port and lan 3 seem to be swapped:
I can get an IP via DHCP from lan 1, 2 and 4 (wan), but not 3

Quote:

root@DD-WRT:~# reboot
Reserved instruction in kernel code[#1]:
Cpu 0
$ 0 : 00000000 00000000 fffffffc c081d90c
$ 4 : c0823a4e 00000003 00000001 00000000
$ 8 : 00000001 0000fc00 00000000 803ba000
$12 : 00008000 00000000 0e054f00 00000007
$16 : c081d8f0 c0821000 c081d908 c0801000
$20 : 802857e0 00020000 00000000 00000000
$24 : 8028bb78 00989641
$28 : 80af0000 80af1f98 00000000 80b67984
Hi : 00000000
Lo : 00000000
epc : 80b67fe4 Tainted: P
ra : 80b67984 Status: 1100fc03 KERNEL EXL IE
Cause : 10800028
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process RtmpWscTask (pid: 681, threadinfo=80af0000, task=803ed248)
Stack : 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 80003c54 00000000 1100fc03 00000000 00000000 00000000
00000000 80003c44 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:[<80003c54>][<80003c44>]

Code: 00000000 00000000 20646142 <656c6966> 73656420 70697263 00726f74 00000000 00000000
Reserved instruction in kernel code[#2]:
Cpu 0
$ 0 : 00000000 00000000 fffffffc c081d90c
$ 4 : c0823a4e 00000003 00000001 00000000
$ 8 : 00000001 0000fc00 00000000 80af0000
$12 : 00008000 00000000 0e9de580 00000007
$16 : c081d8f0 c0821000 c081d908 c0801000
$20 : 802857e0 00020000 00000000 00000000
$24 : 8028bb78 00989641
$28 : 80414000 80415f98 00000000 80b67984
Hi : 00000000
Lo : 28b0a800
epc : 80b67fe4 Tainted: P D
ra : 80b67984 Status: 1100fc03 KERNEL EXL IE
Cause : 10800028
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process RtmpWscTask (pid: 694, threadinfo=80414000, task=8036c530)
Stack : 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 80003c54 00000000 1100fc03 00000000 00000000 00000000
00000000 80003c44 dad35362 f1c5084c f230dce4 93f658be db1495d3 2db10900
7cd304af c53c3f99
Call Trace:[<80003c54>][<80003c44>]

Code: 00000000 00000000 20646142 <656c6966> 73656420 70697263 00726f74 00000000 00000000
Terminated
root@DD-WRT:~# device vlan2 left promiscuous mode
device br0 left promiscuous mode
Restarting system.

U-Boot 1.1.3 (Nov 25 2008 - 10:57:31)

Board: Ralink APSoC DRAM: 16 MB
relocate_code Pointer at: 80fa8000

The MANUFACT ID =000000C2

The Flash ID =000022A7

Set info->start[0]=BFC00000
flash_protect ON: from 0xBFC00000 to 0xBFC24E27
protect on 0
protect on 1
protect on 2
flash_protect ON: from 0xBFC30000 to 0xBFC3FFFF
protect on 3
============================================
Ralink UBoot Version: 3.1
--------------------------------------------
ASIC 3052_MP1 (MAC to GigaMAC Mode)
Product Name: ESR-9752-SC
DRAM COMPONENT: 128Mbits
DRAM BUS: 16BIT
Total memory: 16 MBytes
Flash: 4 MBytes
Date:Nov 25 2008 Time:10:57:31
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 16 bit
SDRAM size =16 Mbytes
SDRAM CAS = 3(d1835272)

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
4 3 2 1 0

3: System Boot system code via Flash.
## Booting image at bfc50000 ...
Image Name: DD-WRT v24 Linux Kernel Image
Created: 2009-07-19 14:20:37 UTC

System Control Status = 0x21440000
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 857044 Bytes = 837 kB
Load Address: 80000000
Entry Point: 80267000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80267000) ...
## Giving linux memsize in MB, 16

Starting kernel ...

LINUX started...

THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #581 Sun Jul 19 16:16:58 CEST 2009

The CPU frequency set to 384 MHz
16M RAM Detected!
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists in Zone order. Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 10800020, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 003a9800(3840000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13260k/16384k available (2141k kernel code, 3124k reserved, 315k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
Load RT2880 Timer Module(Wdg/Soft)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x800000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Ralink SoC physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

found squashfs at 122000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00050000-0x003f0000 : "linux"
0x00122000-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
IPP2P v0.8.2 loading
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00 256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
decode /dev/mtdblock4
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 120k freed
starting Architecture code for rt2880
rt2860v2_ap: module license 'unspecified' taints kernel.

phy_tx_ring = 0x0084c000, tx_ring = 0xa084c000, size: 16 bytes

phy_rx_ring = 0x0084d000, rx_ring = 0xa084d000, size: 16 bytes
RT305x_ESW: Link Status Changed
GDMA1_FWD_CFG = 10000
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Algorithmics/MIPS FPU Emulator v1.5
device vlan1 entered promiscuous mode
device eth2 entered promiscuous mode
RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
0x1300 = 00064380
Terminate the task(RtmpWscTask) with pid(726)!
0x1300 = 00064380
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
br0: port 1(vlan1) entering learning state
wland: No such file or directory
device vlan2 entered promiscuous mode
device vlan2 left promiscuous mode
device vlan2 entered promiscuous mode
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
SIOCGIFFLAGS: No such device
device br0 entered promiscuous mode
SIOCGIFFLAGS: No such device
etherip: Ethernet over IPv4 tunneling driver
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
RT305x_ESW: Link Status Changed
RT305x_ESW: Link Status Changed
RT305x_ESW: Link Status Changed
RT305x_ESW: Link Status Changed
RT305x_ESW: Link Status Changed
RT305x_ESW: Link Status Changed
RT305x_ESW: Link Status Changed
RT305x_ESW: Link Status Changed
submit_button=[index] submit_type=[changepass]
name=[index] type=[changepass] service=[] sleep=[1] action=[5]

U-Boot 1.1.3 (Nov 25 2008 - 10:57:31)

Board: Ralink APSoC DRAM: 16 MB
relocate_code Pointer at: 80fa8000

The MANUFACT ID =000000C2

The Flash ID =000022A7

Set info->start[0]=BFC00000
flash_protect ON: from 0xBFC00000 to 0xBFC24E27
protect on 0
protect on 1
protect on 2
flash_protect ON: from 0xBFC30000 to 0xBFC3FFFF
protect on 3
============================================
Ralink UBoot Version: 3.1
--------------------------------------------
ASIC 3052_MP1 (MAC to GigaMAC Mode)
Product Name: ESR-9752-SC
DRAM COMPONENT: 128Mbits
DRAM BUS: 16BIT
Total memory: 16 MBytes
Flash: 4 MBytes
Date:Nov 25 2008 Time:10:57:31
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 16 bit
SDRAM size =16 Mbytes
SDRAM CAS = 3(d1835272)

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
4 3 2 1 0

3: System Boot system code via Flash.
## Booting image at bfc50000 ...
Image Name: DD-WRT v24 Linux Kernel Image
Created: 2009-07-19 14:20:37 UTC

System Control Status = 0x21440000
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 857044 Bytes = 837 kB
Load Address: 80000000
Entry Point: 80267000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80267000) ...
## Giving linux memsize in MB, 16

Starting kernel ...

LINUX started...

THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #581 Sun Jul 19 16:16:58 CEST 2009

The CPU frequency set to 384 MHz
16M RAM Detected!
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists in Zone order. Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 800008, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 003a9800(3840000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13260k/16384k available (2141k kernel code, 3124k reserved, 315k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
Load RT2880 Timer Module(Wdg/Soft)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x800000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Ralink SoC physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

found squashfs at 122000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00050000-0x003f0000 : "linux"
0x00122000-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
IPP2P v0.8.2 loading
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00 256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
decode /dev/mtdblock4
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 120k freed
starting Architecture code for rt2880
rt2860v2_ap: module license 'unspecified' taints kernel.

phy_tx_ring = 0x0084e000, tx_ring = 0xa084e000, size: 16 bytes

phy_rx_ring = 0x0084f000, rx_ring = 0xa084f000, size: 16 bytes
RT305x_ESW: Link Status Changed
GDMA1_FWD_CFG = 10000
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
CPU 0 Unable to handle kernel paging request at virtual address 0000000c, epc == 8002adbc, ra == 8002adf0
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000000 80251e78 fffffffc
$ 4 : 80250000 80951de4 00000006 00000000
$ 8 : 00000072 00000000 00000000 fffffff8
$12 : 6e2f3476 69667465 7265746c 5f70692f
$16 : 00000000 80951de4 80f285ec 80c7dcc8
$20 : 8031fb54 803182a0 8031fbc0 80c7dd30
$24 : 00000001 800a95a4
$28 : 80c7c000 80c7dc78 00000000 8002adf0
Hi : 00000530
Lo : 34834f78
epc : 8002adbc Tainted: P
ra : 8002adf0 Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 0000000c
PrId : 0001964c
Modules linked in: rt2860v2_ap(P)
Process preinit (pid: 629, threadinfo=80c7c000, task=80384590)
Stack : 00000001 80290000 80c86980 80951de4 80c86980 800a8e38 00000001 00000001
00000000 80290000 8031fb54 80951dcc 80c7dea8 80c7dd28 800a969c 8007d414
800a8e28 800a8e14 8033a01d 80c7dd30 80f285ec 00000000 80f285ec 80951dcc
80070414 800703f4 800a966c 80c7dd38 800702f0 80070414 8033a01d 80c7dd30
8031fb54 80c7dea8 00000000 8033a000 00000310 000001b6 80071848 80072194
...
Call Trace:[<800a8e38>][<800a969c>][<8007d414>][<800a8e28>][<800a8e14>][<80070414>][<800703f4>][<800a966c>][<800702f0>][<80070414>][<80071848>][<80072194>][<80072b10>][<800646e8>][<800708fc>][<800730cc>][<8006838c>][<8007d414>][<800740b0>][<80058b1c>][<800743e8>][<8000c55c>][<8000c52c>][<80064bd0>][<80025638>][<800646e8>][<800708fc>][<80064c88>][<80064c4c>][<8000a6c4>][<8002601c>]

Code: 3c048025 24901e78 2603fffc <8c620010> 1440000c 00000000 8c62000c 24420001 ac62000c
Segmentation fault

ÿ;ÿþ

U-Boot 1.1.3 (Nov 25 2008 - 10:57:31)

Board: Ralink APSoC DRAM: 16 MB
relocate_code Pointer at: 80fa8000

The MANUFACT ID =000000C2

The Flash ID =000022A7

Set info->start[0]=BFC00000
flash_protect ON: from 0xBFC00000 to 0xBFC24E27
protect on 0
protect on 1
protect on 2
flash_protect ON: from 0xBFC30000 to 0xBFC3FFFF
protect on 3
============================================
Ralink UBoot Version: 3.1
--------------------------------------------
ASIC 3052_MP1 (MAC to GigaMAC Mode)
Product Name: ESR-9752-SC
DRAM COMPONENT: 128Mbits
DRAM BUS: 16BIT
Total memory: 16 MBytes
Flash: 4 MBytes
Date:Nov 25 2008 Time:10:57:31
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 16 bit
SDRAM size =16 Mbytes
SDRAM CAS = 3(d1835272)

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
4 3 2 1 0

3: System Boot system code via Flash.
## Booting image at bfc50000 ...
Image Name: DD-WRT v24 Linux Kernel Image
Created: 2009-07-19 14:20:37 UTC

System Control Status = 0x21440000
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 857044 Bytes = 837 kB
Load Address: 80000000
Entry Point: 80267000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80267000) ...
## Giving linux memsize in MB, 16

Starting kernel ...

LINUX started...

THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #581 Sun Jul 19 16:16:58 CEST 2009

The CPU frequency set to 384 MHz
16M RAM Detected!
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists in Zone order. Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 80007c, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 003a9800(3840000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13260k/16384k available (2141k kernel code, 3124k reserved, 315k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
Load RT2880 Timer Module(Wdg/Soft)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x800000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Ralink SoC physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

found squashfs at 122000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00050000-0x003f0000 : "linux"
0x00122000-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
IPP2P v0.8.2 loading
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00 256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
decode /dev/mtdblock4
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 120k freed
starting Architecture code for rt2880
rt2860v2_ap: module license 'unspecified' taints kernel.

phy_tx_ring = 0x0084e000, tx_ring = 0xa084e000, size: 16 bytes

phy_rx_ring = 0x0084f000, rx_ring = 0xa084f000, size: 16 bytes
RT305x_ESW: Link Status Changed
GDMA1_FWD_CFG = 10000
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Algorithmics/MIPS FPU Emulator v1.5
device vlan1 entered promiscuous mode
device eth2 entered promiscuous mode
RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
0x1300 = 00064380
Terminate the task(RtmpWscTask) with pid(726)!
0x1300 = 00064380
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
br0: port 1(vlan1) entering learning state
wland: No such file or directory
device vlan2 entered promiscuous mode
device vlan2 left promiscuous mode
device vlan2 entered promiscuous mode
SIOCGIFFLAGS: No such device
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
SIOCGIFFLAGS: No such device
device br0 entered promiscuous mode
etherip: Ethernet over IPv4 tunneling driver
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device

DD-WRT v24-sp2 std (c) 2009 NewMedia-NET GmbH
Release: 07/19/09 (SVN revision: 12526)
ÿ
DD-WRT login: root
Password:
==========================================================

____ ___ __ ______ _____ ____ _ _
| _ \| _ \ \ \ / / _ \_ _| __ _|___ \| || |
|| | || ||____\ \ /\ / /| |_) || | \ \ / / __) | || |_
||_| ||_||_____\ V V / | _ < | | \ V / / __/|__ _|
|___/|___/ \_/\_/ |_| \_\|_| \_/ |_____| |_|

DD-WRT v24-sp2
http://www.dd-wrt.com

==========================================================
Jan 1 00:00:15 login[1036]: root login on 'console'

BusyBox v1.13.4 (2009-07-19 16:18:16 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

root@DD-WRT:~#

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 14:51 Post subject:

Crash of changing password:

Quote:

root@DD-WRT:~# connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
submit_button=[index] submit_type=[changepass]
name=[index] type=[changepass] service=[] sleep=[1] action=[5]
CPU 0 Unable to handle kernel paging request at virtual address 00000004, epc == 80067db8, ra == 800648b8
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000000 806825c0 806825c0
$ 4 : 00000000 80c88e88 806825c0 806825c0
$ 8 : 00000000 80c087a0 ffffffe0 fffffff8
$12 : 8033b3a0 00000000 2ac15088 2ac117e8
$16 : 806825c0 80764478 804f9000 00000000
$20 : 80a2ab40 803183a0 00000001 00400c5c
$24 : 00000002 00000000
$28 : 803ba000 803bbe40 7fb8fc60 800648b8
Hi : 082d45a7
Lo : 58af85ed
epc : 80067db8 Tainted: P
ra : 800648b8 Status: 1100fc03 KERNEL EXL IE
Cause : 0080000c
BadVA : 00000004
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process resetbutton (pid: 680, threadinfo=803ba000, task=80c3e790)
Stack : fffffff2 7ff85a00 00000012 80130190 806825c0 803bbea8 804f9000 00000012
ffffff9c 004009f8 80064b8c 803bbea8 804f9000 00000012 ffffff9c 004009f8
00000000 00400c5c 00000000 80064c00 00000000 00000000 0000000e 00000080
803bbea8 00000000 80a2ab40 803183a0 00000000 00000000 7ff85ea4 00000101
00000001 00000000 80c26b60 00000000 ffffff9c 004009f8 800646e8 00000012
...
Call Trace:[<80130190>][<80064b8c>][<80064c00>][<800646e8>][<800708fc>][<80064c88>][<80064c4c>][<8002d2f8>][<8000a6c4>]

Code: 8ca40000 ac620004 acc40000 <ac860004> aca60000 acc50004 03e00008 00000000 8c830000
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 80144044, ra == 80143ec8
Oops[#2]:
Cpu 0
$ 0 : 00000000 00000000 00000000 00000000
$ 4 : 802e05c0 804de370 00000000 8034f000
$ 8 : 0000ffff 80f25812 80ff9480 00000015
$12 : 752a8000 00000015 a5408000 000002ae
$16 : ffffffe8 80ff9480 00000081 802e05c0
$20 : 8034f000 802857e0 8034f000 802d0000
$24 : 8028bb78 00000010
$28 : 803ba000 803bbb00 00000020 80143ec8
Hi : 00000002
Lo : 0065b9aa
epc : 80144044 Tainted: P D
ra : 80143ec8 Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 00000000
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process resetbutton (pid: 680, threadinfo=803ba000, task=80c3e790)
Stack : 3d8db092 8028bb78 803e18b8 8001b638 80ff9480 8034f000 80ff9480 8034f000
000000ca 803ea000 00000001 802d0000 80109bbc 80109b30 803e18b8 00000000
80250000 8001c924 803ea000 803ed6c0 8034f134 8034f000 802e01e8 00001b8b
802e01f8 80250000 802857e0 00000001 7fb8fc60 80147260 8028bbb0 803bbb88
00000000 80290000 0000012c 800288f0 00000000 8029093c 00000009 80290000
...
Call Trace:[<8001b638>][<80109bbc>][<80109b30>][<8001c924>][<80147260>][<800288f0>][<800286e0>][<800287dc>][<80001e18>][<80023130>][<80007ca8>][<80007cac>][<8000c6d8>][<8000c494>][<80067db8>][<800648b8>][<800720ac>][<80072194>][<80072ac8>][<80001e00>][<800708fc>][<800648b8>][<80067db8>][<80130190>][<80064b8c>][<80064c00>][<800646e8>][<800708fc>][<80064c88>][<80064c4c>][<8002d2f8>][<8000a6c4>]

Code: 1052002a 00000000 2470ffe8 <8e030018> cc600000 26020018 1453fff8 00000000 10c00013
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 1 seconds..

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 15:26 Post subject:

Quote:

root@DD-WRT:~# nvram commit
CPU 0 Unable to handle kernel paging request at virtual address 00000004, epc == 8013fc5c, ra == 802062a4
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000000 00000000 ffffffff
$ 4 : 00000000 00000000 00000049 00000000
$ 8 : 00000000 00000000 00000000 8024e000
$12 : 00000000 00000000 db5a5700 00000004
$16 : 80c88000 00000000 80c2a560 80b4db9c
$20 : 00000000 80b4db8c 00000000 7fb8dcf8
$24 : 01f59f00 8020628c
$28 : 80b4c000 80b4db40 80b4db8c 802062a4
Hi : 00000000
Lo : 00000000
epc : 8013fc5c Tainted: P
ra : 802062a4 Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 00000004
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process ead (pid: 775, threadinfo=80b4c000, task=803e18b8)
Stack : 0fffff00 8004d1b4 00000000 00200200 80c88000 802062a4 803e18b8 80290b20
80b4db9c 00000000 80b4db94 00000000 80076c74 80000000 80a57abc 80a052a8
00000abc 2aaaf000 00000000 00000000 00000001 00000007 00000001 00000010
802fdc40 000a00d2 00000000 80303c00 00000001 80303c00 8028195c 805cc540
803e18b8 2aaaf000 80b4dca8 00030000 8028195c 805cc540 8000c55c 8000c52c
...
Call Trace:[<8004d1b4>][<802062a4>][<80076c74>][<8000c55c>][<8000c52c>][<800583ec>][<800586b8>][<80047dac>][<80047ba4>][<8000c55c>][<8000c52c>][<80077c34>][<8001c92c>][<800702f0>][<800702a4>][<80205658>][<800ff01c>][<800f870c>][<801353d4>][<80072ac8>][<8001cf38>][<8001ced4>][<8001b66c>][<80022844>][<80022798>][<8001bfd8>][<80039378>][<80054bb8>][<8005be20>][<802064c0>][<80206540>][<8005ca34>][<8005c9c0>][<801356e4>][<80138f98>][<801375cc>][<80152c10>][<80152ae4>][<801395b4>][<8013983c>][<80076f9c>][<8000a6c4>][<8000a6c4>]

Code: 00000000 8e020100 2403ffff <c0440004> 7c640004 e0440004 108000fd 00000000 8fbf0014
CPU 0 Unable to handle kernel paging request at virtual address 00000034, epc == 8007102c, ra == 80070ff4
Oops[#2]:
Cpu 0
$ 0 : 00000000 00000000 00002000 00000000
$ 4 : 00000000 00000001 00000000 00000000
$ 8 : 00000000 80c087a0 ffffffe0 fffffff8
$12 : 00000000 00000000 e44b2880 00000004
$16 : 80c89790 80a21ea8 00000001 00000000
$20 : 00000004 80c08b80 00000002 000000ff
$24 : 0ae67080 2ac36860
$28 : 80a20000 80a21e08 00000000 80070ff4
Hi : 00000000
Lo : 00000000
epc : 8007102c Tainted: P D
ra : 80070ff4 Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 00000034
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process ledtool (pid: 1040, threadinfo=80a20000, task=80c550c8)
Stack : 00000000 80a21ea8 804f9000 00000004 800741cc 33e34813 00000000 80a21ea8
804f9000 00000004 00000001 004005cc 80074378 fffffff2 33e34813 00000014
80216190 00000014 00000001 00000000 80a21eb8 8003c8e0 00000001 00000000
00000000 80a21ea8 804f9000 000000ff ffffff9c 004005cc 00000002 004007f0
00000000 80064bd0 80a21eb8 80a21f20 1dcd6500 8003cd90 80a21ea8 004005cc
...
Call Trace:[<800741cc>][<80074378>][<80216190>][<8003c8e0>][<80064bd0>][<8003cd90>][<800646e8>][<800708fc>][<80064c88>][<80064c4c>][<8003cf3c>][<8000a6c4>]

Code: 10820044 00000000 8e03008c <8c620034> 30420001 1440006b 32820002 8e0200fc 30420004
CPU 0 Unable to handle kernel paging request at virtual address 00000034, epc == 8007102c, ra == 80070ff4
Oops[#3]:
Cpu 0
$ 0 : 00000000 00000000 00002000 00000000
$ 4 : 00000000 00000001 00000000 00000000
$ 8 : 00000000 80c087a0 ffffffe0 fffffff8
$12 : 80c2a1e0 00000000 2ac15088 2ac117e8
$16 : 80c89790 803bbea8 00000001 00000000
$20 : 00000004 80c08b80 00000001 00000012
$24 : 00000002 2ac36860
$28 : 803ba000 803bbe08 7fb8fc60 80070ff4
Hi : 082d45a7
Lo : 58af85ed
epc : 8007102c Tainted: P D
ra : 80070ff4 Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 00000034
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process resetbutton (pid: 680, threadinfo=803ba000, task=80c3e790)
Stack : 00000000 803bbea8 804ff000 00000004 800741cc 7ff85af0 00000000 803bbea8
804ff000 00000004 00000001 004009f8 80074378 803bbe60 fffffff2 7ff85a00
00000012 80130190 00000001 004009f8 00000001 00400c5c 69646172 66666f6f
00000000 803bbea8 804ff000 00000012 ffffff9c 004009f8 00000001 00400c5c
7fb8fc60 80064bd0 00000000 00000000 0000000e 00000080 803bbea8 00000000
...
Call Trace:[<800741cc>][<80074378>][<80130190>][<80064bd0>][<800646e8>][<800708fc>][<80064c88>][<80064c4c>][<8002d2f8>][<8000a6c4>]

Code: 10820044 00000000 8e03008c <8c620034> 30420001 1440006b 32820002 8e0200fc 30420004
CPU 0 Unable to handle kernel paging request at virtual address 0000000c, epc == 8008b570, ra == 800723e8
Oops[#4]:
Cpu 0
$ 0 : 00000000 00000000 00000000 08351121
$ 4 : 80eb2790 00000001 08351121 00000000
$ 8 : 80291f80 80290000 80a21cd8 ffffffec
$12 : 0000005c 06ceba25 2ab41088 2ab3d7e8
$16 : 80eb2790 00000001 80c88800 80a21e80
$20 : 00000000 80c8b000 00000101 00000000
$24 : 00000001 2ab60f90
$28 : 80a20000 80a21cf8 7f92b9e8 800723e8
Hi : 0000015e
Lo : 0003584f
epc : 8008b570 Tainted: P D
ra : 800723e8 Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 0000000c
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process udhcpc (pid: 1041, threadinfo=80a20000, task=80c550c8)
Stack : 80c8b00b 80a21d38 00000015 08351121 00000015 08351121 80eb2790 80bce304
8031a268 800723e8 803382a0 80318320 00000000 80318320 803181a0 80bce304
d76c835a 00000006 80c8b005 80c08b80 803382a0 80318320 80385134 80a21e80
80a21d80 80c8b000 00000000 00000000 80072b10 80db1f00 80b169e0 80cd1ba0
803051a0 8004a07c 80385134 80318320 00000000 00030002 80a21eb8 00000101
...
Call Trace:[<800723e8>][<80072b10>][<8004a07c>][<800730cc>][<8006838c>][<800740b0>][<800741cc>][<8006bec0>][<8000c52c>][<8006d530>][<800708fc>][<800063b0>][<8000638c>][<8000a6c4>][<8000a6c4>]

Code: 10400007 8c92008c 8e420024 <8c42000c> 10400003 00000000 0040f809 00000000 8e0600f4
nvram_commit(): CPU 0 Unable to handle kernel paging request at virtual address 0000001c, epc == 8007f9f0, ra == 800738e4
end
Oops[#5]:
Cpu 0
$ 0 : 00000000 2aaef900 000003bf 00000010
$ 4 : 80703580 80703590 00000000 802559d0
$ 8 : 80290000 00000000 80e01e80 fffffff0
$12 : 0000028b 07c5304b 2ab85088 2ab817e8
$16 : 80703580 80bf3000 80703580 80db7114
$20 : 80e01ec8 00400670 00000002 00400890
$24 : 00000001 8007fa68
$28 : 80e00000 80e01e98 00000000 800738e4
Hi : 0000019a
Lo : 0003d169
epc : 8007f9f0 Tainted: P D
ra : 800738e4 Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 0000001c
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process nvram (pid: 1037, threadinfo=80e00000, task=803f8028)
Stack : 00000000 80bf3000 80703580 80db7114 00000000 80bf3000 800738e4 800738e4
800f0d08 800f0d00 7fcdbda4 00400670 8031bf20 803181a0 278ab619 00000007
80bf3005 00000010 00000000 00000000 00000014 00400670 00000002 00400890
00000000 80067b28 803e5f00 80c2a4e0 00000000 8006625c 00000000 2aaef838
00000000 7fcdbda8 00000000 004ac3d4 7fcdbda4 8000a6c4 00000000 7fccbb50
...
Call Trace:[<800738e4>][<800738e4>][<800f0d08>][<800f0d00>][<80067b28>][<8006625c>][<8000a6c4>]

Code: 00003021 2442ffff ad022704 <8d31001c> 12200016 00003821 0c0202cd 00000000 0220f809
Segmentation fauCPU 0 Unable to handle kernel paging request at virtual address 0000000c, epc == 8008b570, ra == 800723e8
lt
Oops[#6]:
Cpu 0
$ 0 : 00000000 7fcec810 00000000 2a2e93a2
$ 4 : 8064b388 00000001 2a2e93a2 00000000
$ 8 : 80291f80 80290000 80477cb0 fffffff8
$12 : 00000000 00000000 00000000 00000000
$16 : 8064b388 00000001 80c88c00 80477ea8
$20 : 00000000 8033a000 00000101 000001b6
$24 : 00000000 2ab5a860
$28 : 80476000 80477cd0 80280000 800723e8
Hi : 0000040b
Lo : 41a41feb
epc : 8008b570 Tainted: P D
ra : 800723e8 Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 0000000c
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process sh (pid: 1036, threadinfo=80476000, task=80c36b98)
Stack : 8033a00b 80477d10 00000015 2a2e93a2 00000015 2a2e93a2 8064b388 80a572a8
80cd76c8 800723e8 00001cb1 00000b3b 7f1c0300 00000115 80318320 80a572a8
ceb0fa2e 00000006 8033a005 0000e100 80338b00 80318320 80385134 80477ea8
80477d58 8033a000 00000000 000001b6 80072b10 800287dc 00001500 00000005
00001cb1 00000b30 80385134 80318320 7fcec948 80f37ee0 40087468 00000101
...
Call Trace:[<800723e8>][<80072b10>][<800287dc>][<800646e8>][<800708fc>][<800730cc>][<8006838c>][<800ee26c>][<800740b0>][<800741cc>][<80058b1c>][<80074360>][<8000c55c>][<8000c52c>][<80064bd0>][<800ee26c>][<800646e8>][<800708fc>][<80064c88>][<80064c4c>][<8000a6c4>]

Code: 10400007 8c92008c 8e420024 <8c42000c> 10400003 00000000 0040f809 00000000 8e0600f4
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 80069680, ra == 8004ebdc
Oops[#7]:
Cpu 0
$ 0 : 00000000 00000000 00000000 00000000
$ 4 : 80c88c40 80398188 1100fc00 ffff00fe
$ 8 : 803a1fe0 0000fc00 00000000 8024e000
$12 : 00000000 00000000 e2359980 00000005
$16 : 00000000 80c88c40 80255830 80250000
$20 : 80290000 80290000 00000000 00000000
$24 : 08d0e180 00989640
$28 : 803a0000 803a1ed0 00000000 8004ebdc
Hi : 00000000
Lo : 00000000
epc : 80069680 Tainted: P D
ra : 8004ebdc Status: 1100fc03 KERNEL EXL IE
Cause : 00800008
BadVA : 00000000
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process pdflush (pid: 54, threadinfo=803a0000, task=80398188)
Stack : 80398188 80398188 ff3dae05 8028bb78 80250000 80255630 803a1f7c 80250000
8004ebdc 80398188 8001c33c 8001c328 80398188 8004f480 ffff8703 8028bb78
00000000 00000000 803a1f08 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000025 00000000 80250000 80255630 803a1f7c 80250000
80290000 80290000 8004f580 8004f548 80214648 80214628 00000001 8004f480
...
Call Trace:[<8004ebdc>][<8001c33c>][<8001c328>][<8004f480>][<8004f580>][<8004f548>][<80214648>][<80214628>][<8004f480>][<8004eb80>][<8004f480>][<80038edc>][<80038ec0>][<80003c54>][<80003c44>]

Code: 1440000c 02202021 00608021 <8c630000> 1612fff9 cc600000 8fbf0020 8fb3001c 8fb20018
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 80144044, ra == 80143ec8
Oops[#8]:
Cpu 0
$ 0 : 00000000 00000000 00000000 00000000
$ 4 : 802e05c0 804de370 00000000 8034f000
$ 8 : 0000ffff 80847012 80348b00 80708000
$12 : af088000 0000002f c2008000 00000beb
$16 : ffffffe8 80348b00 00000081 802e05c0
$20 : 8034f000 802857e0 8034f000 802d0000
$24 : 8028bb78 00989640
$28 : 8024e000 8024fdb0 00000020 80143ec8
Hi : 00000beb
Lo : c2000000
epc : 80144044 Tainted: P D
ra : 80143ec8 Status: 1100dc03 KERNEL EXL IE
Cause : 00800008
BadVA : 00000000
PrId : 0001964c
Modules linked in: nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre etherip rt2860v2_ap(P)
Process swapper (pid: 0, threadinfo=8024e000, task=80250188)
Stack : 1a1630dd 00000000 0000001a 334c9000 80348b00 8034f000 80348b00 8034f000
000000ad 803ea000 00000001 802d0000 80109bbc 80109b30 00000000 c0801000
80c6ec80 00001000 803ea000 00000000 8034f134 8034f000 802e01e8 ffff955c
802e01f8 80250000 802857e0 00000000 00000000 80147260 00000000 8024fe38
80290b20 80290000 0000012c 80291bfc 00000000 8029093c 0000000a 80290000
...
Call Trace:[<80109bbc>][<80109b30>][<80147260>][<800286e0>][<8026a500>][<800287dc>][<80001544>][<800287dc>][<80001e18>][<80038f18>][<80001974>][<80003eb8>][<80003ea0>][<80001978>][<800d952c>][<80267d00>][<80267254>]

Code: 1052002a 00000000 2470ffe8 <8e030018> cc600000 26020018 1453fff8 00000000 10c00013
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 1 seconds..

Also, I noticed this:

Quote:

mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only

Is this any reason for concern?

Last edited by GraveR on Sun Jul 19, 2009 15:35; edited 1 time in total

BrainSlayer
Site Admin

Joined: 06 Jun 2006
Posts: 7492
Location: Dresden, Germany

Posted: Sun Jul 19, 2009 15:35 Post subject:
no. from what i see here its a problem with accessing the last block of the flash chip. i can reproduce this here on a ESR6650 too which is my current testing device. it seems to affect only the 29lv320btc flash chip _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 15:36 Post subject:
Sorry, you're right. nvram commit causes all the fuss. And I'm 'blessed' with that particular flash chip too

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 15:53 Post subject:
The thing about LAN3 and WAN being swapped is hereby confirmed; I get a WAN IP when putting a 'live' cable in LAN3.

BrainSlayer
Site Admin

Joined: 06 Jun 2006
Posts: 7492
Location: Dresden, Germany

Posted: Sun Jul 19, 2009 16:31 Post subject:
usually. the port swapping is no big problem. i know how to deal with it. right now the firmware is running on my device here, but i still need to make a special build for your device _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 16:33 Post subject:

BrainSlayer wrote:

usually. the port swapping is no big problem. i know how to deal with it. right now the firmware is running on my device here, but i still need to make a special build for your device

Great! I'll keep my eyes peeled for something to test Laughing

Again, thanks so far!

BrainSlayer
Site Admin

Joined: 06 Jun 2006
Posts: 7492
Location: Dresden, Germany

Posted: Sun Jul 19, 2009 16:49 Post subject:
try this _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 16:53 Post subject:

BrainSlayer wrote:

try this

Looks promising, will test further:

Quote:

root@DD-WRT:~# nvram commit
nvram_commit(): end

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 17:00 Post subject:

Sehr gut!

Quote:

Router Name DD-WRT
Router Model Senao ESR9752
LAN MAC 00:0C:43:30:52:77
WAN MAC 00:0C:43:30:52:78
Wireless MAC 00:0C:F6:5B:45:94
WAN IP 192.168.1.215
LAN IP 192.168.99.1

Lan ports are OK, too!

Routing confirmed working.

More to come...

GraveR
DD-WRT Novice

Joined: 13 Jul 2009
Posts: 32

Posted: Sun Jul 19, 2009 17:09 Post subject:
Everything I tested works, including wireless (none, WEP, WPA), UPnP. Nice! The only thing not correct is "sorry, your unit does not support resetbutton feature", well it is has one

Goto page Previous 1, 2, 3, 4, 5, 6, 7, 8, 9 Next

Display posts from previous:

Page 2 of 9

DD-WRT Forum Index -> Ralink SoC based Hardware

All times are GMT

Navigation

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Log in

Sitecom WL-342 (rebadged Senao ESR-9752-SC) Support?

Quick Links

Log in