Posted: Tue Sep 01, 2026 16:52 Post subject: New Build - 08/31/2026 - r66073
Welcome to MediaTek r66073 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Posted: Wed Sep 02, 2026 14:57 Post subject: Router reboots after 4 seconds flashing
Router/Version: Dlink DIR-882 A1
File/Kernel: Linux 6.12.101 #1582 SMP Wed Aug 5 04:10:37 +06 2026 mips
Previous/Reset: DD-WRT v3.0-r65876 std (08/05/26) / No
Mode/Status: Router / AP
Issues/Errors: Router reboots after 4 seconds flashing.
Shows in the browswer: http://192.168.1.1/Success_u_s.asp
Starts up with firmware version: DD-WRT v3.0-r65876 std (08/05/26) - the version I'm on now
This problem started sinds version: 08-15-2026-r65953
Joined: 08 May 2018 Posts: 17402 Location: Texas, USA
Posted: Wed Sep 02, 2026 15:48 Post subject:
Did you try flashing via CLI? You'd have to SCP the webflash file to the router since wget and curl cannot process the Anubis challenge and FTP binary is usually not available within the firmware. Need to know if the firmware image size is too big, etc. Serial or tailing syslog during flashing may also give some info. Can't forward report without further info. Still waiting on any reports on Netgear devices, too. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... RSS feed for DD-WRT releases (2025) RSS feed for DD-WRT releases (2024) RSS feed for DD-WRT releases (2023)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Did you try flashing via CLI? You'd have to SCP the webflash file to the router since wget and curl cannot process the Anubis challenge and FTP binary is usually not available within the firmware. Need to know if the firmware image size is too big, etc. Serial or tailing syslog during flashing may also give some info. Can't forward report without further info. Still waiting on any reports on Netgear devices, too.
Never tried flashing from CLI before... i'm afraid to brick my router...
