Posted: Thu May 21, 2026 4:07 Post subject: New Build - 05/20/2026 - r65079
Welcome to x86 / x64 r65079 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
It is taking over 30 minutes to download an image. _________________ Custom computer w/ i7-13700T, 16GB DDR5 Ram, X710-T4L, i226 four port, two RLTK 8127 cards & dual AQC113 M2 slot card. Currently running OpenWRT and Adguard.
2 GL.iNET GL-BE9300 Flint 3 with (GLiNet Custom OpenWRT) as AP's (WIFI 7 for the whole home now)
GL.iNET GL-MT6000 Flint 2 with pure OpenWRT not in use
GL INET GL-BE3600 Slate 7 Travel Router as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r65574) one used as a bridge
WRT54G-TM not in use
This resulted always in unresponding webinterface and browser (tested firefox and chromium) losing connection in an instant.
According to /var/log/messages always this happens:
Code:
May 21 12:12:00.296 N4000 user.info : [httpd] : maybe died, we need to re-exec it
May 21 12:12:00.320 N4000 daemon.info httpd[31855]: [httpd] : httpd server started at port 80
Since I have a complete backup of the device, I decided to give a try for those fancy new 2GB big "ext4" files:
What am I doing wrong? Or is a new install via dd neded?
Or do I have to start the update via CLI this time?
Since I never made an update via CLI before, am I right to assume I'd have to download "the file" WHICH ONE into /tmp and write it to a partition (Again which one)?
Joined: 06 Jun 2006 Posts: 7824 Location: Dresden, Germany
Posted: Thu May 21, 2026 17:47 Post subject:
these new files will only work if already a new fw is installed. a older firmware will not accept this. its shit i know but i had to go this way. so backup your config and do a raw image install. future upgrades hopefully will just went fine. if you do a raw update the config will also remain since its stored in a unaccessible place at the end of the drive. so using dd or physdiskwrite will work fine _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7824 Location: Dresden, Germany
Posted: Thu May 21, 2026 17:52 Post subject:
cml750 wrote:
It is taking over 30 minutes to download an image.
where are you from? we have a good 10gig bandwidth on our server on decix in germany _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
It is taking over 30 minutes to download an image.
where are you from? we have a good 10gig bandwidth on our server on decix in germany
I am in Southeast Texas USA. I have over a 1 gig connection. _________________ Custom computer w/ i7-13700T, 16GB DDR5 Ram, X710-T4L, i226 four port, two RLTK 8127 cards & dual AQC113 M2 slot card. Currently running OpenWRT and Adguard.
2 GL.iNET GL-BE9300 Flint 3 with (GLiNet Custom OpenWRT) as AP's (WIFI 7 for the whole home now)
GL.iNET GL-MT6000 Flint 2 with pure OpenWRT not in use
GL INET GL-BE3600 Slate 7 Travel Router as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r65574) one used as a bridge
WRT54G-TM not in use
Router/Version: see sig
File/Kernel: Full VGA EXT4 EFI
Previous/Reset: Clean install
Mode/Status: Router
Issues/Errors: Nothing major after a few minutes
I was able to get Adguard up an running. In the "Networking" tab, unused ports show up with error 1, but work normally when connected. I am hoping the upgrade works next time there is an update using the Full VGA EXT4 EFI upgrade file. Ethtool via Entware still gives a segmentation fault.
I had reinstalled my QCNCM865 "Fast connect 7800" hoping it would work now that BrainSlayer has the Ath12K drivers but alas, no wifi tab. _________________ Custom computer w/ i7-13700T, 16GB DDR5 Ram, X710-T4L, i226 four port, two RLTK 8127 cards & dual AQC113 M2 slot card. Currently running OpenWRT and Adguard.
2 GL.iNET GL-BE9300 Flint 3 with (GLiNet Custom OpenWRT) as AP's (WIFI 7 for the whole home now)
GL.iNET GL-MT6000 Flint 2 with pure OpenWRT not in use
GL INET GL-BE3600 Slate 7 Travel Router as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r65574) one used as a bridge
WRT54G-TM not in use
Joined: 06 Jun 2006 Posts: 7824 Location: Dresden, Germany
Posted: Sat May 23, 2026 7:36 Post subject:
cml750 wrote:
Router/Version: see sig
File/Kernel: Full VGA EXT4 EFI
Previous/Reset: Clean install
Mode/Status: Router
Issues/Errors: Nothing major after a few minutes
I was able to get Adguard up an running. In the "Networking" tab, unused ports show up with error 1, but work normally when connected. I am hoping the upgrade works next time there is an update using the Full VGA EXT4 EFI upgrade file. Ethtool via Entware still gives a segmentation fault.
I had reinstalled my QCNCM865 "Fast connect 7800" hoping it would work now that BrainSlayer has the Ath12K drivers but alas, no wifi tab.
entware is external. i dont know how these programs are compiled and which libc is in use. i can integrate ethtool of course on my side.
will be available in next release _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Thank you BrainSlayer! You are the man! There are a few others that will be very happy to have Ethtool added to the builds! _________________ Custom computer w/ i7-13700T, 16GB DDR5 Ram, X710-T4L, i226 four port, two RLTK 8127 cards & dual AQC113 M2 slot card. Currently running OpenWRT and Adguard.
2 GL.iNET GL-BE9300 Flint 3 with (GLiNet Custom OpenWRT) as AP's (WIFI 7 for the whole home now)
GL.iNET GL-MT6000 Flint 2 with pure OpenWRT not in use
GL INET GL-BE3600 Slate 7 Travel Router as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r65574) one used as a bridge
WRT54G-TM not in use
Joined: 10 May 2022 Posts: 146 Location: Texas, USA
Posted: Sat May 23, 2026 15:42 Post subject:
Router/Version: Micro-Star International Co., Ltd. PRO B550M-VC WIFI (MS-7C95) w/AMD Ryzen 5 / DD-WRT v3.0-r65079 std (05/20/26)
File/Kernel: Linux 6.12.90 #1086 SMP Wed May 20 15:35:21 +06 2026 x86_64
Previous/Reset: Fresh install
Mode/Status: Gateway / up 1 day, 8:52
Issues/Errors: QoS seems not working (service priority packets count never updated); Queuing Discipline option no longer available
I flashed my SSD with the full_efi_vga_ext4 image. Happy to report that it resolved my constant "AMD-Vi: Completion-Wait Loop timed out" console message issue (see my post https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=341365).
I was able to use GParted to resize partition 2 with no issue. System boots up normal and df command now shows /dev/root to be 6155876K mounted on "/" while /dev/sda3 remain at 117203K and mounted on /usr/local and /jffs. Not sure what I did will affect the next upgrade or not. I guess I will find out soon after the next release is ready.
entware is external. i dont know how these programs are compiled and which libc is in use. i can integrate ethtool of course on my side.
will be available in next release
Yeah, please
Very good news for including ethtool.
Fidling with entware only for this is just a Pain in the butt.
Those i226v have abysmal ipv6 throughput if not rx-gro-list set to disabled.
