Posted: Fri Jan 30, 2026 23:09 Post subject: New Build - 01/30/2026 - r63600
Welcome to x86 / x64 r63600 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: industrial PC N4000 4GB RAM, 2*intel i226-v
File: x86-64/web/dd-wrt_x64-webupgrade_full_vga_2GB.bin
Firmware: DD-WRT v3.0-r63600 std (01/31/26) prev. DD-WRT v3.0-r62606 (11/12/2025)
Kernel: 6.12.67 #757 SMP Sat Jan 31 01:26:41 +07 2026 x86_64
Mode: Gateway, SFE disabled, Wireguard for external access, WAN (ETH0) (PPPoE/VLAN7) to GPON Modem, ETH1 to LAN, Automatic Drive Mount disabled - using own mount script for USB Disk, nfs to access USB3-ext4 SSD, Force reconnect 5:00 in the morning, using my own local NTP, CPU governour set to ondemand by script, Ignore WAN DNS, Recursive DNS Resolving (Unbound), using NAT66, DHCP disabled.
Reset: No
Status: All good again .
PHP working.
NAT66 with ULA working again!
Websites testing for IPv6 report IPv6 again . Traceroute, mtr, ping, iperf3 and nslookup or dig aaaa are working again for IPv6.
I did not even fiddle with new nftables, ip(6)tables entries seem to do their job!
One Question:
Is it possible to include ethtool in this build? I have to disable "rx-gro-list" on my eth1 to reach full IPv6 throughput. In the past I used opkg and its variant of ethtool, but I wanna get rid of it (also its variant of ethtool is outdated and segfaults in recent releases).
Nevertheless, I'm very happy this build is working. Thank you for your efforts Brainslayer and all devs and people involved!
Posted: Mon Feb 02, 2026 16:03 Post subject: New Build - 01/30/2026 - r63600
Gigabyte Technology Co., Ltd. Z97X-Gaming 3 Intel(R) Core(TM) i7-5775C CPU @ 3.30GHz 32 gb ddr3 Seems like a good build everything is working rather well. Sfe is disabled also and for my wifi solution netgear wndr 4300 is also doing well thanks again devs.
Joined: 25 Aug 2020 Posts: 58 Location: New York, USA
Posted: Fri Feb 13, 2026 23:05 Post subject:
Router/Version: HP-8055 i3-6100T, x86-64
File/Kernel: dd-wrt_x64-webupgrade_full_vga_2GB.bin
Previous/Reset: r61613, no
Mode/Status: Gateway, Online and working
Issues/Errors: n/a
The past several months of builds have been problematic for me, but I'm not seeing any problems on this one. Up for 3 hours now with no issues. Thanks! _________________ HP EliteDesk 800 G2 Mini PC [i3-6100T] (Gateway: DHCP, DNS, QoS, etc)
TP-Link BE9300 (WAP, not running dd-wrt)
NETGEAR WNDR4300 (Switch)
Router/Version: Optiplex 7060, i7-8700, 32 GB Ram, X710-T4L, I226 4 Port
File/Kernel: dd-wrt_x64_full_efi_vga_2GB .bin
Previous/Reset: Fresh install, I was using OpenWRT
Mode/Status: Router
Issues/Errors: n/a
I did a fresh install this morning and have had zero issues except I am unable to get an activation code from the activation center. I have previously activated fresh installs 3 times on this computer. The build itself seems very stable so far.
Router/Version: Optiplex 7060, i7-8700, 32 GB Ram, X710-T4L, I226 4 Port
File/Kernel: dd-wrt_x64_full_efi_vga_2GB .bin
Previous/Reset: Fresh install, I was using OpenWRT
Mode/Status: Router / Adguard Home
Issues/Errors: Under Setup / Networking tab, the unused ports on my i226 four port card show error-1. The card itself is working properly so far. The USB drive used for Entware with opt and jffs partitions, is not automatically mounting after reboot.
I am able to get Adguard running by adding a mount command to the startup command used to start Adguard.
mount /dev/sdb1 /opt
sleep 20
/opt/etc/init.d/rc.unslung start _________________ Optiplex 7060 with i7-8700, 32GB Ram, X710-T4L, i226 four port, & an AQC113 M2 slot card. DDWRT 63600 & Adguard Home.
GL.iNET GL-BE9300 Flint 3 with OpenWRT as an AP
GL.iNET GL-MT6000 Flint 2 with OpenWRT as an AP
GL INET GL-BE3600 Slate 7 Travel Router with OpenWRT as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r62268) one used as a bridge
WRT54G-TM not in use
One thing I noticed about this build is the CPU clock is no longer pegged at the max. The CPU goes down to the minimal state when there is no load and maxes out quickly when under load. The pegged out CPU never really bothered me so I never used the script to force it to speedstep but it appears at some point Brainslayer added the speedstep back to the main image. _________________ Optiplex 7060 with i7-8700, 32GB Ram, X710-T4L, i226 four port, & an AQC113 M2 slot card. DDWRT 63600 & Adguard Home.
GL.iNET GL-BE9300 Flint 3 with OpenWRT as an AP
GL.iNET GL-MT6000 Flint 2 with OpenWRT as an AP
GL INET GL-BE3600 Slate 7 Travel Router with OpenWRT as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r62268) one used as a bridge
WRT54G-TM not in use
.