[Corb]

Router/Version: Linksys MX5300
File/Kernel: dd-wrt-webupgrade.bin (r63355) / Linux 6.6.120-rt29 #5003 SMP Wed Jan 14 16:45:55 +07 2026 aarch64
Previous/Reset: DD-WRT v3.0-r63295 std (09/01/25) / no
Mode/Status: AP, NNS-ECM-SFE, AP, OpenVPN server
Wifi: WLAN0 5GHz AC/N Mixed 80MHz, WLAN1 5GHz AX/AC/N Mixed 80MHz, WLAN2 2.4GHz Mixed 20MHz, WPA2/WPA3-Personal,
Issues/Errors: Working / WLAN1 no radio signal transmission (as in previous version), temp sensor indicated -255.0 °C

Thanks BS and devs

[pbphoto]

Router/Version: Netgear R7800 (x2) DD-WRT v3.0-r63355 std (01/14/26)
Kernel: Linux 6.1.160-rt28 #761 SMP Wed Jan 14 14:29:44 +07 2026 armv7l
Previous/Reset: 07/12/2025 release, no reset
Mode/Status: 'router' operating mode / wifi AP 802.11rvk + usteer / default networking / SFE disabled / Firewall disabled
Uptime: 1.5 days
Issues/Errors: Both my R7800s had VANILLA wifi driver restarts on both radios on this release, and also r63257 and 63230 too. Switched to the DD-WRT wifi firmware and things have been great for 1.5 days now.

Router/Version: Linksys MR7350 DD-WRT v3.0-r63355 std (01/14/26)
Kernel: Linux 6.6.120-rt29 #5001 SMP Wed Jan 14 06:40:36 +07 2026 aarch64
Previous/Reset: r63257 no reset
Mode/Status: 'Gateway' operating mode / wifi AP 802.11rvk + usteer / WAN auto-config DHCP / Wireguard client Mullvad / QCA-NSS subsystem enabled / SFE disabled / DHCP / DNSmasq / Firewall
Uptime: 1.5 days
Issues/Errors: None

[Per Yngve Berg]

Router/Version: Netgear R7800

No IPv6 PD from ISP. Suspect IGMP is not handled properly by the Firewall

Back to 63230

[sumbuddie]

Tried this build on my EA8500.

2.4GHz WiFi clients couldn't connect - switched from Vanilla to DD-WRT firmware on 2.4GHz and all was fine. (My 5GHz is already set to dd-wrt instead of vanilla).

Same issues persist for me regarding IPTV. One of my IPTV receivers can't see the PVR across the network. I don't know if IGMP snooping is working or if multicast to unicast is active on the LAN ports - according to the syslog, this is the case despite the networking tab having the LAN ports configured with multi to uni disabled. If I revert to build r60742 (prior to switching to DSA) all works well.

From the log:

Jan 16 23:17:46.224 Linksys EA8500 user.info : [bridge] : interface wan successfully added to bridge br0
Jan 16 23:17:46.225 Linksys EA8500 user.info : [bridge] : set multicast to unicast for wan
Jan 16 23:17:46.375 Linksys EA8500 user.info : [bridge] : interface lan1 successfully added to bridge br0
Jan 16 23:17:46.375 Linksys EA8500 user.info : [bridge] : set multicast to unicast for lan1
Jan 16 23:17:46.521 Linksys EA8500 user.info : [bridge] : interface lan2 successfully added to bridge br0
Jan 16 23:17:46.521 Linksys EA8500 user.info : [bridge] : set multicast to unicast for lan2
Jan 16 23:17:46.672 Linksys EA8500 user.info : [bridge] : interface lan3 successfully added to bridge br0
Jan 16 23:17:46.672 Linksys EA8500 user.info : [bridge] : set multicast to unicast for lan3
Jan 16 23:17:46.812 Linksys EA8500 user.info : [bridge] : interface lan4 successfully added to bridge br0
Jan 16 23:17:46.813 Linksys EA8500 user.info : [bridge] : set multicast to unicast for lan4


I haven't tested whether or not there are still issues with using the WAN port when it's set to disabled and (ideally) assigned to the switch as I rewired the physical connection setup I was using prior. (used to use the WAN port as the connection to the other router/gateway - now have it connecting on LAN1)

[mvrk]

Router/Version: Netgear R9000
File/Kernel: DD-WRT v3.0-r63355 std (01/14/26)
Previous/Reset: DD-WRT v3.0-r55109 std (02/09/2024) / Yes
Mode/Status: Router / Working Normally
Issues/Errors: None

Router/Version: TP-Link Archer C7 v2
File/Kernel: DD-WRT v3.0-r63355 std (01/14/26)
Previous/Reset: DD-WRT v3.0-r57793 std (08/08/24) / Yes
Mode/Status: Router / Working Normally
Issues/Errors: None