Posted: Sun Sep 21, 2025 11:04 Post subject: New Build - 09/20/2025 - r62170
Welcome to x86 / x64 r62170 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
I have never posted a new build before but I thought I would give it a try. If I missed anything I apologize. _________________ Optiplex 7060 with i7-8700, 32GB Ram, X710-T4L, i226 four port, & an AQC113 M2 slot card. DDWRT 63600 & Adguard Home.
GL.iNET GL-BE9300 Flint 3 with OpenWRT as an AP
GL.iNET GL-MT6000 Flint 2 with OpenWRT as an AP
GL INET GL-BE3600 Slate 7 Travel Router with OpenWRT as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r62268) one used as a bridge
WRT54G-TM not in use
I didn't see any fixes in the SVN tracker for the Realtek 2.5 Gbpe 8125b adapters yet.
The ticket was reopened after 62157. I was going to try it in case he did something and failed to list it for some reason. I had time to mess with it earlier when the build folder was empty. Now I am tied up so it will be later this week. _________________ Optiplex 7060 with i7-8700, 32GB Ram, X710-T4L, i226 four port, & an AQC113 M2 slot card. DDWRT 63600 & Adguard Home.
GL.iNET GL-BE9300 Flint 3 with OpenWRT as an AP
GL.iNET GL-MT6000 Flint 2 with OpenWRT as an AP
GL INET GL-BE3600 Slate 7 Travel Router with OpenWRT as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r62268) one used as a bridge
WRT54G-TM not in use
Router/Version: industrial PC N4000 4GB RAM, 2*intel i226-v
File: dd-wrt_x64-webupgrade_full_vga_2GB.bin
Firmware: DD-WRT v3.0-r62170 std (09/20/25)
Kernel: Linux 6.12.48 #187 SMP Sat Sep 20 11:46:34 +07 2025 x86_64
Mode: Gateway, SFE disabled, Wireguard for external access, WAN (PPPoE/VLAN7) to GPON Modem, Automatic Drive Mount disabled - using own mount script for USB Disk, nfs to access USB3-ext4 SSD, Force reconnect 5:00 in the morning, using my own local NTP, CPU governour set to ondemand by script, Ignore WAN DNS, Recursive DNS Resolving (Unbound).
Reset: No
Status: Installed on Sunday, ERROR.
PPPoE does not start after reboot. Status --> WAN states connected, but nothing happens. You have to click "disconnect" there in order to connect.
This behaviour started with one build before previous release.
You can reboot the router and wait hours but rp-pppoe.so gets loaded and pppd 2.4.8 started only after a click on disconnect.
