Posted: Thu Jun 12, 2025 6:52 Post subject: New Build - 06/12/2025 - r61745
Welcome to Atheros r61745 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Notes:... r61542r61557r61613r61648r61711r61745 • r60771-r61745 migrates IPQ806x from swconfig to DSA however VLAN configurations will not; no more Switch Config tab.
• IPQ806x: Asrock G10, Linksys EA8500, Netgear R7500, R7500v2, R7800, XR500 (XR450) & Trendnet TEW-827DRU v1.0R.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Posted: Thu Jun 12, 2025 8:37 Post subject: WR841ND
Router/Version: TP-Link TL-WR841ND v11
Update method: WebUpgrade
File/Kernel: tl-wr841nd-webflash.bin_r61745 / Linux 3.18.140-d6 #242270 Thu Jun 12 06:59:23 +07 2025 mips
Previous/Reset: r61711 / no
Mode/Status: AP wired and wireless / Up and running for 2:16
Issues/Errors: Nothing significant
If your router's light turns red, don't worry. Internet connection is ok.
Incorrect rate of wlan0 - 800 Mbit/s!
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 59468
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 62032
Broadcom
Asus RT-AC88U - DD-WRT 62032
Asus RT-AC87U R - DD-WRT 62032
Asus RT-N66U - DD-WRT 62032
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
Joined: 16 Nov 2015 Posts: 7043 Location: UK, London, just across the river..
Posted: Thu Jun 12, 2025 10:28 Post subject:
Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r61745 std (06/12/25)
Kernel Version Linux 6.1.141-rt28 #586 SMP Sun Jun 8 12:19:18 +07 2025 armv7l
update: CLI
reset: NO
mode: Gateway/DNScrypt-proxy v2 via Entware, AD-Block (via script),IPset Firewall,Forced DNS,AP&Net Isolation,x2VLAN,VPN client(PBR),40 HT 2.4Ghz only(Vanilla), Disable 121
status: Operational 1h+
errors: Nothing new, yet...Thanks BS and Team !
Router Model Dynalink DL-WRX36
Firmware Version DD-WRT v3.0-r61745 std (06/12/25)
Kernel Version Linux 6.6.93-rt29 #3484 SMP Wed Jun 11 23:22:29 +07 2025 aarch64
update: GUI
reset: NO
mode: Gateway/DNScrypt-proxy v2 via Entware, AD-Block (via DNSmasq & DNScrypt script),IPset Firewall,Forced DNS,AP & Net Isolation, x4VLAN, VPN client(PBR),40 HT 2.4Ghz only(Vanilla), Disable 121
status: Operational 1h+
errors: WAN orange light still in blink mode...!!
...Thanks BS and Team ! _________________ Atheros
TP-Link WR1043NDv2 -DD-WRT 62606 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 -DD-WRT 62890 GTW/SmDNS/DoT,AD-Blk,Forced DNS,AP&Net Isolation,x2VLAN,Vanilla
Netgear R7800 --DD-WRT 62606 Gateway/DNSCryptv2,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla,VPN cli
Netgear R9000 --DD-WRT 62606 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Dynalink DL-WRX36-DDWRT 62606
Broadcom
Netgear R7000 --DD-WRT 63020 GTW/DNScrypt-proxy2/AD-Block,IPset Firewall,Forced DNS,x4VLAN,VPN cli
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Router/Version: Linksys MR7350
File: dd-wrt-webupgrade.bin
Firmware: DD-WRT v3.0-r61745 std (06/12/25)
Kernel: Linux 6.6.93-rt29 #3484 SMP Wed Jun 11 23:22:29 +07 2025 aarch64
Mode: Gateway, SFE disabled, 2.4G and 5G wifi, bridged VAP on 2.4GHz, Wireguard for external access, WAN disabled, Keep Alive reboot 6:02 in the morning, using my own local NTP
Reset: No
Status: Ok.
Joined: 07 Jan 2025 Posts: 228 Location: Bethel Park, PA, USA
Posted: Thu Jun 12, 2025 17:49 Post subject:
Router/Version: Linksys MR7350 x 3
File/Kernel: DD-WRT v3.0-r61745 std (06/12/25), Linux 6.6.93-rt29 #3484 SMP Wed Jun 11 23:22:29 +07 2025 aarch64
Previous/Reset: DD-WRT v3.0-r61711 std (06/09/25), last reset on r61711
Mode/Status: Gateway (NSS-ECM), Access Point (5GHZ-HT20 AX/AC/N mixed, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES), performance governor, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS/DNSMasq, OpenVPN server, Wireguard Server + 2 Wired access points (2.4GHz-HT20 N/G Mixed, 5GHZ-HT80 AX/AC/N mixed, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES)
Issues/Errors:
Up 4 hours. USB 3.2 stick working properly for Entware and "jffs" partitions. Speed, wired and wifi, is very close to published, which is equal or favorable to the ISP router - tested via nPerf.com. Wireguard and OpenVPN servers both working as expected and throughput sufficient to open video files on network shares. 5GHz showing 22dBm (set to 30dBm). 2.4GHz showing 28dBm (also set to 30dBm).
MAC address of br1 in the Networking tab is displayed as a random single ASCII character (even after full reset), but this is not service-affecting. No issues so far.
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r61745 std (06/12/25)
Previous/Reset: DD-WRT v3.0-r59171 std (01/14/25), full reset and reconfig
Mode/Status: Wired access points (2.4GHz-HT20 N/G Mixed, 5GHZ-HT80 AC/N mixed, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES, DD-WRT firmware)
Issues/Errors:
Up 2 hours. 5GHz Wireless speed on the primary and guest wifi networks are close to published. 2.4GHz showing 30dBm and 5GHz showing 24dBm (both set for 30dBm).
Wanted to see how the revamped Networking worked on this router, as I may need to send it to my daughter to replace the crappy one from her ISP. Basically copied the settings from the MR7350. I did notice that the 2.4GHz is consistently slightly slower than the MR7350 - ~58Mbps vs 66Mbps. Same display issue with the MAC on br1 as above. Otherwise, worked perfectly.
Thank you Brainslayer. _________________ Formerly dpp3530 Linksys MR7350
Gateway, 2 wired APs, NSS-ECM , Clock 1440MHz
VAPs on wlan0 and wlan1 for guest/IOT devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
SmartDNS (DOT using NextDNS, Cloudflare), DNSMasq
Wireguard and OpenVPN server
2.4GHz: dd-wrt, AX Only, ACK Timing 1350, WPA3 SAE & WPA2 w/AES
5GHz: dd-wrt, AX/AC/N Mixed, ACK Timing 1350, WPA3 SAE & WPA2 w/AES
Verizon Fios, 500/500Mbps
R7800 - seems that this build kills WAN DHCP if NSS-ECM-SFE is enabled, cannot get IP from cable modem. Just SFE works fine. Couple of builds ago it was not an issue. Anybody else?
Joined: 08 May 2018 Posts: 16574 Location: Texas, USA
Posted: Fri Jun 13, 2025 1:21 Post subject:
Router Model: Buffalo WZR-HP-G300NH
Firmware Version: DD-WRT v3.0-r61745 std (06/12/25)
Previous: DD-WRT v3.0-r60791 std (04/28/25)
File: wzr-hp-g300nh-dd-wrt-webupgrade-MULTI.bin,buffalo_to_ddwrt_webflash-MULTI.bin
Kernel Version: Linux 3.10.108-d11 #200482 Thu Jun 12 03:33:30 +07 2025 mips
Mode: Gateway/AP/Android Tethering WAN Reset: Yes (webUI flash is f*cked. TFTP recovered to this build and loaded backup taken prior to flash)
Status: OK
Uptime: ~30m
Issues/Errors: None, save and except that webUI flashing this device is now completely b0rked. It *used* to sit and the diagnostic LED flash forever until finally rebooting and coming back up. Now, it cuts off at some point and does not write the image to flash, whatsoever. Unfortunately, I have never opened this one up to attach serial, nor was I tailing the log, but it's been f*cked the past several builds I've tried via webUI the past year or two.
Router: Netgear R7800
Version: DD-WRT v3.0-r61745 std (06/12/25) via CLI flash (/tmp/firmware.bin)
File: dd-wrt-webupgrade.bin
Kernel: Linux 6.1.141-rt28 #586 SMP Sun Jun 8 12:19:18 +07 2025 armv7l
Previous: DD-WRT v3.0-r61613 std (06/02/25)
Reset: No
Mode: Gateway, wlan0 & 1 AP, DNSCrypt (non-Entware), Android Tethering WAN.
Status: Ok
Uptime: ~30 min
Issues/Errors: None. Automatic upgrade via /tmp/firmware.bin still works flawlessly. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... RSS feed for DD-WRT releases (2025) RSS feed for DD-WRT releases (2024) RSS feed for DD-WRT releases (2023)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
R7800 - seems that this build kills WAN DHCP if NSS-ECM-SFE is enabled, cannot get IP from cable modem. Just SFE works fine. Couple of builds ago it was not an issue. Anybody else?
Yes, all builds since r60791 seem to be incompatible with ipq806x R7800 when NSS acceleration is enabled.
MAC address of br1 in the Networking tab is displayed as a random single ASCII character (even after full reset), but this is not service-affecting. No issues so far.
This has gone on far too long and while it's not a show-stopper, it's annoying as hell!
AsX wrote:
R7800 - seems that this build kills WAN DHCP if NSS-ECM-SFE is enabled, cannot get IP from cable modem. Just SFE works fine. Couple of builds ago it was not an issue. Anybody else?
Oddly enough, I have found disconnecting all the LAN ports allows the WAN to get an IP address. No idea why. I have been seeing this on and off since r60771 on an EA8500. Easy solution was to just stick with SFE instead of my once working VERY WELL NSS-ECM setting.
Molle wrote:
AsX wrote:
R7800 - seems that this build kills WAN DHCP if NSS-ECM-SFE is enabled, cannot get IP from cable modem. Just SFE works fine. Couple of builds ago it was not an issue. Anybody else?
Yes, all builds since r60791 seem to be incompatible with ipq806x R7800 when NSS acceleration is enabled.
This affects EA8500 as well. As long as this situation exists, it basically means there was never any need to add NSS cores since they are not working now anyway and taking up lots of EPROM space (lots of kernel modules) for a feature that is now pretty much worthless. _________________ - Linksys EA8500: I-Gateway, WAP/VAP 5ghz only. Features: VLANs, Samba, WG, Entware - r60xxx
- Linksys EA8500: 802.11s Secondary w/VLAN Trunk over 5ghz - r60xxx
- Linksys MX4300: 802.11s Primary w/VLAN Trunk over 5ghz. 2.4ghz WAP/VAP only - r60xxx
- Linksys MX4300: (WAP/VAP (7)) Multiple VLANs over single trunk port. Entware/Samba r60xxx
- Linksys MR7350: WDS Station for extended Ethernet r60xxx
- Linksys MR7500, MX8500: None in production. Just testing. r60xxx
- OSes: Fedora 40, 10 RPis (2,3,4,5), 23 ESP8266s: Straight from Amiga to Linux in '95, never having owned a Windows PC.
- Forum member #248
Joined: 05 Oct 2008 Posts: 835 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Fri Jun 13, 2025 7:04 Post subject:
dplotz wrote:
Router/Version: Linksys MR7350 x 3
...
MAC address of br1 in the Networking tab is displayed as a random single ASCII character (even after full reset), but this is not service-affecting. No issues so far.
Router/Version: Netgear R7800
...
Same display issue with the MAC on br1 as above. Otherwise, worked perfectly.
Thank you Brainslayer.
On my R7800 on the various latest builds the MAC for br1 (named differently, but the only one I've added) has consistently been displaying the same number as for Priority on the same line in the GUI, viz. 32768. Never a single random character.
It doesn't seem to cause any trouble, though.
