Posted: Wed May 14, 2025 10:30 Post subject: New Build - 05/14/2025 - r61264
Welcome to Atheros r61264 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Update method: CLI / SSH flash from konsole over wireless
Router/Version: Linksys MX4200 v1
File/Kernel: dd-wrt-webflash.bin / Linux 6.6.90-rt29 #3287 SMP Wed May 14 05:58:44 +07 2025 aarch64
Previous/Reset: 61238 / No reset, last reset at 61202
Mode/Status: Gateway, AP, PPPoE, NSS-ECM, WAN to ONT, non-default router IP, SmartDNS for DoT to single host, DDNS (TLS enabled), wireguard server (preshared key, non-default port), SSHD (public key only, non-default port), no VAP, wlan0 5GHz VHT80 AC only, wlan1 2.4GHz HT40 N only, wlan2 5GHz HE80 AX only, WPA3 Personal CCMP-128 all radios, TX power 20dBm all radios / Working
Issues/Errors: From build 61238, write command for CLI flash no longer shows write status during flash nor CRC status at end of flash.
Note: As reported already, r61238 did not output the flash update progress lines as usual but this caused no issues and the router flashed properly. _________________ Netgear R9000 DD-WRT v3.0-r61824 std (06/20/25)
Linux 4.9.337 #773 SMP Sat Jun 7 01:25:51 +07 2025 armv7l Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
SmartDNS (using Cloudflare, Quad9 and Google), no QoS, no SFE
2.4GHz: AP, DD-WRT, N Only, ACK Timing 500, WPA2 w/AES
5GHz: AP, DD-WRT, AC Only, ACK Timing 500, WPA2 w/AES
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/40Mbps
Joined: 16 Nov 2015 Posts: 6877 Location: UK, London, just across the river..
Posted: Wed May 14, 2025 12:56 Post subject:
x2 Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r61264 std (05/14/25)
Kernel Version Linux 6.1.138-rt28 #575 SMP Sun May 11 01:20:36 +07 2025 armv7l
update: CLI
reset: NO
mode: Gateway/DNScryptv2 via Entware, AD-Block (via DNSmasq script & DNScrypt),IPset Firewall,Forced DNS,AP&Net Isolation,x2 VLAN,VPN client(PBR),40 HT 2.4Ghz only(Vanilla), Disable 121
status: Operational 1h+
errors: Nothing new, yet...as still no CLI output was reported again...
P.S.
Router Model Netgear XR500
Firmware Version DD-WRT v3.0-r61264 std (05/14/25)
Kernel Version Linux 6.1.138-rt28 #575 SMP Sun May 11 01:20:36 +07 2025 armv7l
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r61264 std (05/14/25)
Kernel Version Linux 3.18.140-d6 #239319 Wed May 14 08:01:47 +07 2025 mips
both working ..!
Thanks BS and Team ! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 58184 WAP
TP-Link WR1043NDv2 -DD-WRT 61745 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 61824 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x2VLAN,Vanilla
Netgear R7800 --DD-WRT 61824 Gateway/DNSCryptv2,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 61711 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Dynalink DL-WRX36-DDWRT 61745
Broadcom
Netgear R7000 --DD-WRT 61745 Gateway/DNScrypt-proxy2/AD-Block,IPset Firewall,Forced DNS,x4VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Wed May 14, 2025 17:45; edited 1 time in total
Joined: 07 Jan 2025 Posts: 154 Location: Bethel Park, PA, USA
Posted: Wed May 14, 2025 16:15 Post subject:
Router/Version: Linksys MR7350 x 3
File/Kernel: DD-WRT v3.0-r61264 std (05/14/25), Linux 6.6.90-rt29 #3285 SMP Wed May 14 03:07:13 +07 2025 aarch64
Previous/Reset: DD-WRT v3.0-r61238 std (05/12/25) , last reset on r60791
Mode/Status: Gateway (NSS-ECM), Access Point (5GHZ-HT20 AX/AC/N mixed, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES), performance governor, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS/DNSMasq, OpenVPN server, Wireguard Server + 2 Wired access points (2.4GHz-HT20 N/G Mixed, 5GHZ-HT80 AX/AC/N mixed, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES)
Issues/Errors:
Up 2.5 hours. USB 3.2 stick working properly for Entware and "jffs" partitions. Speed, wired and wifi, is very close to published, which is equal or favorable to the ISP router - tested via nPerf.com. Wireguard and OpenVPN servers both working as expected and throughput sufficient to open video files on network shares. 5GHz showing 27dBm (set to 30dBm). 2.4GHz showing 28dBm (also set to 30dBm).
example: MAC Address "00:11:22:33:44:55:66"
Hostname: FAN/HEATER
IP Address 192.168.1.5
I can still connect to the router if I manually assign the IP address and gateway on the PC.
DHCP start automatically assigning IP addresses when these characters are removed from the hostname.
Joined: 04 Dec 2007 Posts: 1175 Location: Murrysville, PA
Posted: Thu May 15, 2025 16:08 Post subject:
Minor issue has popped up. Twice, with r61264, the httpd service has hung. I could not get any response from the WebUI. From the CLI, I did "restart httpd" which brought the UI back.
Joined: 30 Jun 2014 Posts: 62 Location: California
Posted: Thu May 15, 2025 19:34 Post subject:
Router/Version: Netgear XR500
Previous/Reset: 03-01-2025-r59964 / no
Issues/Errors: No internet with NSS-SFE, or slow internet with SFE disabled
Perhaps this may provide some clues:
(1) Disabled SFE in 59964 and installed r61264 from CLI. http didn't work until restart httpd from CLI.
(2) Internet speed with SFE disabled was slow (200 Mbps versus 460 before upgrade)
(3) Enabled NSS-SFE and no internet connection.
(4) - disabled SFE, and went back to previously fast & good r59964 with no reset, but still no internet.
- reboot again - still no internet.
- restore backup configuration (has NSS-SFE on), reboots, internet connects!
- speedtest 460 Mbps again.
I previously experienced similar slow internet speeds with r60791 and went back to r59964 (last configuration that I had an nvram backup).
