Posted: Wed Mar 05, 2025 15:01 Post subject: New Build - 03/05/2025 - r60098
Welcome to Marvell r60098 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
After r60098 update - No internet connection. Wifi devices would not connect as well.
Reverted back to r59582 but still would not connect to internet. Restored a r59582 backup and regained connection to internet and all wifi devices connected.
Linksys WRT1900ACS
Firmware DD-WRT v3.0-r60098 std (03/05/25)
Kernel Linux 6.1.129-rt28 #994 SMP Wed Mar 5 05:57:59 +07 2025 armv7l
Upgrade without reset from 03/01/25
Works well. but
CPU ModelMarvell Armada 385
CPU Cores2
CPU Features
VFP VFPv3 NEON VFPD32 EDSP FASTMULT HALF TLS THUMB
CPU Clock1600 MHz
Load Average 51% 1.00, 1.11, 1.17
Interface configuration should've automatically updated unless you had VLANs configured. 59820 is the last build with switch config tab and using eth* interface names on the Networking tab. They are now wan, lan1, lan2, lan3, lan4.
No VLANs configured here =)
Edit: upgrade again to r60098 and this time came up with normal connection. I made no changes just upgraded same as last time. Only dif I could see was no snow flakes this time =D
Router/Version: Linksys WRT1200ac v1
File/Kernel: r60098 Linux 6.1.129-rt28 #994 SMP Wed Mar 5 05:57:59 +07 2025 armv7l
Previous/Reset: r59582 No reset
Mode/Status: Gateway,VPN (WireGuard),Stable
Issues/Errors: Amazon Tablet/Kindles will not connect to WiFi but will connect on r59582. (All other WiFi devices do connect) ProtonVPN OpenVPN setup still will not connect but will on r55630.
Joined: 06 Jun 2006 Posts: 7729 Location: Dresden, Germany
Posted: Thu Mar 06, 2025 2:46 Post subject:
saphirely wrote:
Linksys WRT1900ACS
Firmware DD-WRT v3.0-r60098 std (03/05/25)
Kernel Linux 6.1.129-rt28 #994 SMP Wed Mar 5 05:57:59 +07 2025 armv7l
Upgrade without reset from 03/01/25
Works well. but
CPU ModelMarvell Armada 385
CPU Cores2
CPU Features
VFP VFPv3 NEON VFPD32 EDSP FASTMULT HALF TLS THUMB
CPU Clock1600 MHz
Load Average 51% 1.00, 1.11, 1.17
what means but. if you have high system load, check for running processes and what it causes. mine is zero. and of course. high traffic can cause load too _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Thank you!
the 2nd day, I checked that CPU load is returned to normal.
CPU 66.0 °C
DDR 54.0 °C
WLAN1 54.0 °C
WLAN2 54.0 °C
And Load Average 4% 0.04, 0.03, 0.00
I confirmed that this is a great version. Before this version, all 598xx was the same high CPU.
I did not use QoS, but I choose Adguard/dnsproxy instead of smartdns for DoQ.
After I bricked my WRT1900ACS V1 since April, one of my friend continue his wrt1900acs v2 on 06-19-2024-r56941, this version is stable WRT1900ACS V2 WAN to work with connection of Verizon ISP router's LAN2.
I think it is very old, so suggest to upgrade to final 03-31-2025-r60523 but always returned to 06-19-2024-r56941.
So I try to steps by steps 11-11-2024-r58662, 02-02-2025-r59468 ,03-04-2025-r60090, 03-12-2025-r60269, 03-24-2025-r60467, 03-31-2025-r60523 Yes, it really arrived the 03-31-2025-r60523.
But out of my image, the wrt1900acs v2 works strange.
I try to nslookup www.youtube.com success, gmail.com too, cnet.com all normal.
But when open any website except youtube.com, it cannot work in firefox, chrome, edge.
So I try lots of way, disable DoQ, Disable smartdns, Disable DNScrypt-proxy, and only dnsmasq normal server=1.1.1.1, resetup default of the wrt1900acs v2, still cannot open any website normal. (including setup the linksys WAN 192.168.1.123 in ISP router DMZ).
Even open www.cnet.com, all content inside cannot be clicked.
How ever, all youtube.com is normal.
Return 03-24-2025-r60467, same trouble.
Return 03-12-2025-r60269, same trouble.
I did not know what the hell is, and waste long time, finally decide return 06-19-2024-r56941, yes, all works normal immediately. do not need to defind in DMZ of ISP router
I verified the time of linksys is normal, the wan port inside has been set to wan instead of eth0, SPI firewall disable. all nslookup result normal.
Because it is stranger, so I pasted here. Anyway, my friends think it is better to keep one that old version.
