Posted: Fri Mar 28, 2025 6:16 Post subject: New Build - 03/28/2025 - r60511
Welcome to x86 / x64 r60511 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
These last few builds it seems I had to reset Nvram to get it to work right. It's ok though since I put the DD-WRT on a cheap SSD SATA drive. So I got it up and running on a fresh configuration. It took about 5 minutes after setting it up that everything seemed to work as expected.
Router/Version: 4770k 16gb ram Gigabyte board
File/Kernel: X64 vga full version
Previous/Reset: Had to reset.
Mode/Status: AP/NAS/Gateway
Issues/Errors: Seems ok.
Had to assign my system an ip address and set the gateway to 192.168.1.1 to access the webgui setup.
These last few builds it seems I had to reset Nvram to get it to work right. It's ok though since I put the DD-WRT on a cheap SSD SATA drive. So I got it up and running on a fresh configuration. It took about 5 minutes after setting it up that everything seemed to work as expected.
Router/Version: 4770k 16gb ram Gigabyte board
File/Kernel: X64 vga full version
Previous/Reset: Had to reset.
Mode/Status: AP/NAS/Gateway
Issues/Errors: Seems ok.
Had to assign my system an ip address and set the gateway to 192.168.1.1 to access the webgui setup.
Is it working properly now? _________________ Custom computer w/ i7-13700T, 16GB DDR5 Ram, X710-T4L, i226 four port, RLTK 8111 four port, RLTK 8127 & dual AQC113 M2 slot card. Currently running on OpenWRT & Adguard Home. Plan to get DDWRT with Adguard running soon.
GL.iNET GL-BE9300 Flint 3 with OpenWRT as an AP
GL.iNET GL-MT6000 Flint 2 with OpenWRT as an AP
GL INET GL-BE3600 Slate 7 Travel Router with OpenWRT as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r64137) one used as a bridge
WRT54G-TM not in use
Router/Version: Dell Optiplex 5050 with i7-6700 & 16 GB RAM. Also have a Realtek 4 port 2.5 gbps PCI-E Network card.
File/Kernel: Full 2GB VGA
Previous/Reset: 60467 no reset
Mode/Status: Router
Issues/Errors: None after 5 hours _________________ Custom computer w/ i7-13700T, 16GB DDR5 Ram, X710-T4L, i226 four port, RLTK 8111 four port, RLTK 8127 & dual AQC113 M2 slot card. Currently running on OpenWRT & Adguard Home. Plan to get DDWRT with Adguard running soon.
GL.iNET GL-BE9300 Flint 3 with OpenWRT as an AP
GL.iNET GL-MT6000 Flint 2 with OpenWRT as an AP
GL INET GL-BE3600 Slate 7 Travel Router with OpenWRT as a travel router
2 R7800's (DDWRT Build r60586) Not in use
3 R7000's (DDWRT build r64137) one used as a bridge
WRT54G-TM not in use
