Posted: Fri Mar 28, 2025 6:13 Post subject: New Build - 03/28/2025 - r60511
Welcome to Atheros r60511 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Linksys EA8500 ...main gateway
DD-WRT v3.0-r60511 std (03/28/25)
Linux 6.1.131-rt28 #538 SMP Mon Mar 24 03:43:23 +07 2025 armv7l
scp 'firmware.bin' install over r60502
all good and I had no trouble with r60502 in the time I run it.
Posted: Fri Mar 28, 2025 12:09 Post subject: WR841ND
Router/Version: TP-Link TL-WR841ND v11
Update method: WebUpgrade
File/Kernel: tl-wr841nd-webflash.bin_r60511 / Linux 3.18.140-d6 #234828 Fri Mar 28 08:57:42 +07 2025 mips
Previous/Reset: r60502 / no
Mode/Status: AP wired and wireless / Up and running for 3:31
Issues/Errors: Nothing significant
If your router's light turns red, don't worry. Internet connection is ok.
Channels 12 and 13 are missing
Incorrect rate of wlan0 - 800 Mbit/s!
Even the weird Panama hat doesn't help
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 59468
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 60586
Broadcom
Asus RT-AC88U - DD-WRT 60586
Asus RT-AC87U R - DD-WRT 60586
Asus RT-N66U - DD-WRT 60511
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
Posted: Fri Mar 28, 2025 12:51 Post subject: Re: WR841ND
KACTET wrote:
Router/Version: TP-Link TL-WR841ND v11
Update method: WebUpgrade
File/Kernel: tl-wr841nd-webflash.bin_r60511 / Linux 3.18.140-d6 #234828 Fri Mar 28 08:57:42 +07 2025 mips
Previous/Reset: r60502 / no
Mode/Status: AP wired and wireless / Up and running for 3:31
Issues/Errors: Nothing significant
If your router's light turns red, don't worry. Internet connection is ok.
Channels 12 and 13 are missing
Incorrect rate of wlan0 - 800 Mbit/s!
Even the weird Panama hat doesn't help
Thank you BS and gurus!
Router Model: TP-Link TL-WR841ND v11
Firmware Version: DD-WRT v3.0-r60511 std (03/28/25)
Kernel Version: Linux 3.18.140-d6 #234828 Fri Mar 28 08:57:42 +07 2025 mips
Updated: from r60502 via CLI
Reset: Yes
Status: Working OK as AP, NG Mixed, HT 40
Issues: exactly what KACTET said. Most important ch. 12 and 13 are still missing. As a side effect, due to my crowded wifi environment I'm forced to use ch. 1 which gives me 18 dBm max power. With ch. 13 I had 21 dBm. _________________ Router:TP-Link TL-WR841ND v11
Joined: 07 Jan 2025 Posts: 95 Location: Bethel Park, PA, USA
Posted: Fri Mar 28, 2025 18:01 Post subject:
Router/Version: Linksys MR7350 x 3
File/Kernel: ) DD-WRT v3.0-r60511 std (03/28/25), Linux 6.6.83-rt29 #3000 SMP Thu Mar 27 07:11:53 +07 2025 aarch64
Previous/Reset: DD-WRT v3.0-r60502 std (03/27/25), last reset on r60098
Mode/Status: Gateway (NSS-ECM), Access Point (5GHZ-HT20 AX/AC/N mixed, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES), performance governor, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS/DNSMasq, OpenVPN server, Wireguard Server + 2 Wired access points (2.4GHz-HT20 N/G Mixed, 5GHZ-HT80 AX/AC/N mixed, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES)
Issues/Errors:
Up 5 hours. USB 3.2 stick working properly for Entware and "jffs" partitions. Speed, wired and wifi, is very close to published, which is equal or favorable to the ISP router - tested via nPerf.com. Wireguard and OpenVPN servers both working as expected and throughput sufficient to open video files on network shares. 5GHz showing 27dBm (set to 30dBm). 2.4GHz showing 28dBm (also set to 30dBm).
After reboot, 2.4GHz devices took a few minutes before they would connect. Connecting from Windows, it wouldn't accept the password. After about 5 minutes, they connected normally. 5GHz was unaffected.
Linksys EA8500 ...main gateway
DD-WRT v3.0-r60511 std (03/28/25)
Linux 6.1.131-rt28 #538 SMP Mon Mar 24 03:43:23 +07 2025 armv7l
scp 'firmware.bin' install over r60502
all good and I had no trouble with r60502 in the time I run it.
Worky real fine till few minutes ago. Lost interent. Could not reach router by webif or ssh.
Had to do a power button off/on. All came back just fine but I can't put up with that shit so I booted back into part 2 which has reliable r59171.
Imma prolly 'bout done with new bulds for a while. If I wasn't here it would be broken till I got back to the homeworld.
Custom DNSMasq's X 4 (Involves killing DNSMasq at startup and launching a separate instance for each interface)
SFE only, to make GUI Bandwidth monitoring somewhat useful.(A side effect of hardware acceleration)
WireGuard.
QOS - WAN, HTB, FQ_CODEL (VAPS set to Bulk and that's it)
Reset never in a long long time.
Everything just works except for "can't fork: Out of memory" for a couple scripts, which had no issues prior to r60467. Surely a Kernel change, but why must we limit these "super" routers (compared to old tech) to this process limit.
Other than that, it just works and I had to add some process limits to some scripts. Never any random reboots, never any can't connect issues, it just works.
Wishes: Put the process limits back to where they were.
Thank you for such an awesome firmware to turn these consumer routers into freedom of what we want them to do. _________________ Linksys MX4300
r60511
If you have Entware installed, you could try installing BASH and then change the first line in your script to use bash and not ash. No idea if this will work, but maybe worth trying it. Once bash is installed, you must type "bash" to enter the bash shell in order to test it.
ie:
Code:
#!/bin/sh
change to:
Code:
#!/bin/bash
_________________ - Linksys EA8500: I-Gateway, WAP/VAP 5ghz only. Features: VLANs, Samba, WG, Entware - r60621
- Linksys EA8500: 802.11s Secondary w/VLAN Trunk over 5ghz - r60621
- Linksys MX4300: 802.11s Primary w/VLAN Trunk over 5ghz. 2.4ghz WAP/VAP only - r60269
- Linksys MX4300: (WAP/VAP (7)) Multiple VLANs over single trunk port. Entware/Samba r60269
- Linksys MR7350: WDS Station for extended Ethernet r60662
- Linksys MR7500, MX8500: None in production. Just testing. r60662
- OSes: Fedora 40, 10 RPis (2,3,4,5), 23 ESP8266s: Straight from Amiga to Linux in '95, never having owned a Windows PC.
- Forum member #248
Router/Version: Netgear R7800
File/Kernel: DD-WRT v3.0-r60511 std (03/28/25)
Previous/Reset: DD-WRT v3.0-r60269 std (03/12/25)
Mode/Status: Normal
Issues/Errors: Unsolvable DNS problems. If left at default, DNS 192.168.1.1 does not work, but even if manually set 8.8.8.8, 1.1.1.1, 4.4.4.4 and 1.0.0.1 does not work. Result: does not browse at all. Anger and wasted hours... Solutions?
Now I am using an "emergency" connection.
Unsolvable DNS problems. If left at default, DNS 192.168.1.1 does not work, but even if manually set 8.8.8.8, 1.1.1.1,4.4.4.4 and 1.0.0.1 does not work. Result: does not browse at all.
Anger and wasted hours... Solutions?
Settle down entitled cowboy. You can always go back to your stock firmware. Please don't act; as you already did, that you are entitled to a better firmware from many dedicated people whom express valuable information to the dev, that in turn, develop what you think is owed to you. Learn how and what a router is first,then please by all means, help develop; works for every router, forward and backward, firmware. Your tone sucks and needs matched, so what solutions to your problems are you offering help? _________________ Linksys MX4300
r60511
Unsolvable DNS problems. If left at default, DNS 192.168.1.1 does not work, but even if manually set 8.8.8.8, 1.1.1.1,4.4.4.4 and 1.0.0.1 does not work. Result: does not browse at all.
Anger and wasted hours... Solutions?
Settle down entitled cowboy. You can always go back to your stock firmware. Please don't act; as you already did, that you are entitled to a better firmware from many dedicated people whom express valuable information to the dev, that in turn, develop what you think is owed to you. Learn how and what a router is first,then please by all means, help develop; works for every router, forward and backward, firmware. Your tone sucks and needs matched, so what solutions to your problems are you offering help?
I would say that what you are nervously mumbling about me you should actually write about yourself. Before you talk nonsense, connect your brain.
