Posted: Wed Mar 05, 2025 15:00 Post subject: New Build - 03/05/2025 - r60098
Welcome to Atheros r60098 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Posted: Wed Mar 05, 2025 15:13 Post subject: WR841ND
Router/Version: TP-Link TL-WR841ND v11
Update method: WebUpgrade
File/Kernel: tl-wr841nd-webflash.bin_r60098 / Linux 3.18.140-d6 #232417 Wed Mar 5 10:10:32 +07 2025 mips
Previous/Reset: r60090 / no
Mode/Status: AP wired and wireless / Up and running for 2:12
Issues/Errors: Nothing significant
If your router's light turns red, don't worry. Internet connection is ok.
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 59468
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 60586
Broadcom
Asus RT-AC88U - DD-WRT 60586
Asus RT-AC87U R - DD-WRT 60586
Asus RT-N66U - DD-WRT 60511
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
R9000
no reset
Status: came up clean, a bit faster start -> passing data over wifi than previous builds
Issues - been reported for a while - Wifi lights for 2 and 5ghz do not work
possible issue - not sure if K/R is working correctly clients do not seem to be rebalancing across my WDS AP/STA ints like on previous builds once associated to the 9k. however, i've only been up a few hours so will update tomorrow.
Has anyone figured out what the newly added ARPd switch does at the top of the Services tab?
Thanks to @egc we know what SMCRouted does, in the middle of the Services tab. _________________ - Linksys EA8500: I-Gateway, WAP/VAP 5ghz only. Features: VLANs, Samba, WG, Entware - r60xxx
- Linksys EA8500: 802.11s Secondary w/VLAN Trunk over 5ghz - r60xxx
- Linksys MX4300: 802.11s Primary w/VLAN Trunk over 5ghz. 2.4ghz WAP/VAP only - r60xxx
- Linksys MX4300: (WAP/VAP (7)) Multiple VLANs over single trunk port. Entware/Samba r60xxx
- Linksys MR7350: WDS Station for extended Ethernet r60xxx
- Linksys MR7500, MX8500: None in production. Just testing. r60xxx
- OSes: Fedora 40, 10 RPis (2,3,4,5), 23 ESP8266s: Straight from Amiga to Linux in '95, never having owned a Windows PC.
- Forum member #248
Joined: 06 Jun 2006 Posts: 7708 Location: Dresden, Germany
Posted: Thu Mar 06, 2025 5:42 Post subject:
not just at the services page, but you can switch the arpd feature for individual interfaces on the networking page. the global arpd enable/disable is for br0/lan bridge only
its mainly usefull for bigger networks with a lot of devices. with bigger i mean. bigger than class c. _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
R9000
no reset
Status: came up clean, a bit faster start -> passing data over wifi than previous builds
Issues - been reported for a while - Wifi lights for 2 and 5ghz do not work
possible issue - not sure if K/R is working correctly clients do not seem to be rebalancing across my WDS AP/STA ints like on previous builds once associated to the 9k. however, i've only been up a few hours so will update tomorrow.
Update: connections did appear to rebalance over an extended period, it just took a bit longer to start rebalancing than i expected, so it works it just doesnt kickoff for a while which is ok. supposed to hve some delay anyway, so a bit longer to start is fine.
Joined: 07 Jan 2025 Posts: 116 Location: Bethel Park, PA, USA
Posted: Thu Mar 06, 2025 14:55 Post subject:
Router/Version: Linksys MR7350 x 3
File/Kernel: DD-WRT v3.0-r60098 std (03/05/25), Linux 6.6.80-rt29 #2786 SMP Tue Mar 4 13:59:10 +07 2025 aarch64
Previous/Reset: DD-WRT v3.0-r59964 std (03/01/25), full reset and reconfig on all devices
Mode/Status: Gateway (NSS-ECM-SFE), Access Point (5GHZ AC/N mixed, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES), performance governor, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS/DNSMasq, OpenVPN server, Wireguard Server + 2 Wired access points (DD-WRT firmware, 2.4GHz, 5GHZ, WPA2/WPA3, 802.11r/v/k, guest network, domain:UNITED STATES)
Issues/Errors:
Up 12 hours. USB 3.2 stick working properly for Entware and "jffs" partitions. Speed (tested via nPerf.com) is very close to published, which is equal or favorable to the ISP router. Wireguard and OpenVPN servers both working as expected and throughput sufficient to open video files on network shares. 5GHz showing 22dBm (set to 30dBm). 2.4GHz showing 28dBm (also set to 30dBm).
Guest wifi got pretty unstable on two of the devices after upgrade, clients would lose access after about an hour on the 5GHz only.
Did a full wipe and reconfiguration, and it's been stable since.
I was a bit slow and missed the March 4th build altogether.
Update method: WebUpgrade
Router/Version: GL.iNet-AR150
File/Kernel: DD-WRT v3.0-r60098 std (03/05/25)
Previous/Reset: DD-WRT v3.0-r59171 std (01/14/25) / No reset.
Mode/Status: Gateway, Wireguard, OpenVPN Server and Client, PPTP Server and Client, DDNS, SSH, Wireless Radio Mode: Station
Issues/Errors: Site Survey shows empty list. Incorrect rate of wlan0 - 800 Mbit/s!. Last working release which correctly displayed APs on Site Survey and rate of wlan0 was r59171.
not just at the services page, but you can switch the arpd feature for individual interfaces on the networking page. the global arpd enable/disable is for br0/lan bridge only
its mainly usefull for bigger networks with a lot of devices. with bigger i mean. bigger than class c.
Ah yeah, I missed it in the Networking tab. I can't ever see me needing a class D. Sixty five thousand plus IP addresses is a bit much for my needs lol. _________________ - Linksys EA8500: I-Gateway, WAP/VAP 5ghz only. Features: VLANs, Samba, WG, Entware - r60xxx
- Linksys EA8500: 802.11s Secondary w/VLAN Trunk over 5ghz - r60xxx
- Linksys MX4300: 802.11s Primary w/VLAN Trunk over 5ghz. 2.4ghz WAP/VAP only - r60xxx
- Linksys MX4300: (WAP/VAP (7)) Multiple VLANs over single trunk port. Entware/Samba r60xxx
- Linksys MR7350: WDS Station for extended Ethernet r60xxx
- Linksys MR7500, MX8500: None in production. Just testing. r60xxx
- OSes: Fedora 40, 10 RPis (2,3,4,5), 23 ESP8266s: Straight from Amiga to Linux in '95, never having owned a Windows PC.
- Forum member #248
R9000
no reset
Status: came up clean, a bit faster start -> passing data over wifi than previous builds
Issues - been reported for a while - Wifi lights for 2 and 5ghz do not work
possible issue - not sure if K/R is working correctly clients do not seem to be rebalancing across my WDS AP/STA ints like on previous builds once associated to the 9k. however, i've only been up a few hours so will update tomorrow.
Update: connections did appear to rebalance over an extended period, it just took a bit longer to start rebalancing than i expected, so it works it just doesnt kickoff for a while which is ok. supposed to hve some delay anyway, so a bit longer to start is fine.
Second update, having problems with smb, its locking up on writes, seems to self recover, syslog is spammin local5.err ksmbd: [ksmbd-worker/3854]: ERROR: SRVSVC: unsupported INVOKE method 21
Joined: 03 Nov 2015 Posts: 370 Location: Florida, USA
Posted: Thu Mar 06, 2025 23:08 Post subject:
Router: Netgear R7800 ... WDS AP
Firmware: DD-WRT v3.0-r60098 std (03/05/25)
Kernel: Linux 6.1.129-rt28 #533 SMP Tue Mar 4 06:24:05 +07 2025 armv7l
Reset: NO ... GUI upgrade from r59171
Mode: 2.4 GHz only .. Firmware type VANILLA ..SFE Disabled
Errors: NONE
Router: Linksys ea8500 ... WDS Stations..X (2)
Firmware: DD-WRT v3.0-r60098 std (03/05/25)
Kernel: Linux 6.1.129-rt28 #533 SMP Tue Mar 4 06:24:05 +07 2025 armv7l
Reset: NO ... GUI upgrade from r59887 & r59171
Mode: 2.4 GHz only .. Firmware type VANILLA ..SFE Disabled
Errors: NONE
Everything looks good .. Vaps working good now last few builds.... Woopie !! Back again !! _________________ ......All GOOD here... Just Handshakes and Time Stamps !......
