Posted: Thu Feb 27, 2025 15:09 Post subject: New Build - 02/27/2025 - r59887
Welcome to Marvell r59887 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
No joy with my WRT3200ACM. Still no WAN access with this build. _________________ Linksys WRT3200ACM DD-WRT v3.0-r59171 std (01/14/25) ROUTER
NETGEAR R9000 DD-WRT v3.0-r59171 std (01/14/25) AP
NETGEAR R9000 DD-WRT v3.0-r59171 std (01/14/25) AP
NETGEAR R7000 DD-WRT v3.0-r59171 std (01/14/25) AP
Linksys E4200 DD-WRT v3.0-r59171 mega (01/14/25) AP
NETGEAR ORBI RBR50/RBS50 Voxel (MESH)
Also check the Networking tab and make sure the WAN Assignment is correct. Also the Basic Setup page and make sure the WAN is not disabled there. This could have carried over since it's common now on other routers. _________________ - Linksys EA8500: I-Gateway, WAP/VAP 5ghz only. Features: VLANs, Samba, WG, Entware - r60xxx
- Linksys EA8500: 802.11s Secondary w/VLAN Trunk over 5ghz - r60xxx
- Linksys MX4300: 802.11s Primary w/VLAN Trunk over 5ghz. 2.4ghz WAP/VAP only - r60xxx
- Linksys MX4300: (WAP/VAP (7)) Multiple VLANs over single trunk port. Entware/Samba r60xxx
- Linksys MR7350: WDS Station for extended Ethernet r60xxx
- Linksys MR7500, MX8500: None in production. Just testing. r60xxx
- OSes: Fedora 40, 10 RPis (2,3,4,5), 23 ESP8266s: Straight from Amiga to Linux in '95, never having owned a Windows PC.
- Forum member #248
Joined: 08 May 2018 Posts: 16153 Location: Texas, USA
Posted: Fri Feb 28, 2025 4:06 Post subject:
WAN disabled is not carried over to Marvell AFAIK. I noticed some code changes that were 'incomplete', namely the line in the sysinit that brings up the WAN (wan, formerly eth1). What is now line 140 used to read
Joined: 06 Jun 2006 Posts: 7727 Location: Dresden, Germany
Posted: Fri Feb 28, 2025 5:07 Post subject:
kernel-panic69 wrote:
WAN disabled is not carried over to Marvell AFAIK. I noticed some code changes that were 'incomplete', namely the line in the sysinit that brings up the WAN (wan, formerly eth1). What is now line 140 used to read
not true. the interface wan is up. but it has to be considered that any special configuration involving interfaces like eth0 and eth1 must be fixed by the user to use wan and lan1 lan2 lan3 lan4 interfaces now. if you harm eth0 or eth1 it may break ethernet support
i tested dhcp on wan on a wrt 3200. no issue as it seems
i enabled dhcp and the wan interface got a ip. so please provide more info about your wan configuration (this is entirely missing here)
Joined: 06 Jun 2006 Posts: 7727 Location: Dresden, Germany
Posted: Fri Feb 28, 2025 6:02 Post subject:
saphirely wrote:
Danger: WAN DHCP no WAN IP on
Code:
Linksys WRT1900ACS
DD-WRT v3.0-r59887 std (02/27/25)
Kernel Linux 6.1.129-rt28 #973 SMP Thu Feb 27 10:38:48 +07 2025 armv7l
Return to
Code:
DD-WRT v3.0-r59820 std (02/23/25)
its tested. it works. (unless you made custom configs using eth0 and eth1. interfaces are changed now) _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7727 Location: Dresden, Germany
Posted: Fri Feb 28, 2025 6:04 Post subject:
saphirely wrote:
In my case, it is not easy to capture the screen.
But I found no eth0 ip for WAN only, those other NICs worked normal including oet1.
I did not config any VLAN.
this is correct. eth0 and eth1 are not used and should not be used anymore. the new interface names are wan, lan1, lan2, lan3 and lan4.
if you configured something manually to use eth0 or eth1. please change it to use the correct interface names _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 30 May 2017 Posts: 595 Location: Rural Manitoba
Posted: Fri Feb 28, 2025 16:59 Post subject:
I had same problem with no WAN when I updated yesterday.
Today I reread the posts and in SETUP -> NETWORKING -> INTERFACE SETUP -> WAN PORT ASSIGEMENT I set the value to wan. Had to do a reboot afterwards but otherwise all started fine. _________________ Starlink & DSL ->
WRT3200acm Master WDS 5GHz 80Mhz CH 100 (+6)-r61745
Ath1 2.4Ghz Disabled
99 Static Leases
ExpressVPN
WRT3200acm-r61745 WDS-5Ghz Client
WRT3200acm-r61465 Spare
WRT1900Ac V1 5Ghz-r61745 WDS Station
(Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1-r61745 WDS Station
WRT1900AC SPARE r60942
WRT1900AC SPARE r60942
WRT1900AC V1 5Ghz AC 80Mhz WDS-AP-r61745 2.4Ghz AP Ch1 HT20 Mixed
Joined: 06 Jun 2006 Posts: 7727 Location: Dresden, Germany
Posted: Fri Feb 28, 2025 22:14 Post subject:
marcus83 wrote:
The WAN interface continues not to work on my WRT3200ACM
this is not true. i tested wrt3200acm. its working. fix your config as i told you and follow the instructions if your are using a old wrong config. in worst case. reset your config to defaults. you have old wrong configs in your setup. i will look if i can convert old configs in next releases. _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
