Access restrictions policys won't work. "Filtered Packets 0" mDNS should be blocked and AnyDesk/TeamViewer....
I dont think they are fully operational...
did you do:
-List of Clients
-Interface to block...
-Status - Enable
I also did an experiment on my R7000...and...same as always...it is parsing rules to the DNSmasq in regards to custom rules...but, the operation of dpi and risk rules are questionable...
I also did a test and selected lots of rules (dpi) facebook, microsoft, telnet and others than saved&apply+reboot and tried few on my PC and it can open those with no problem...so..not restricting anything...in regards of those dpi rules i selected... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 58184 WAP
TP-Link WR1043NDv2 -DD-WRT 61264 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 61264 Gateway/DoT,Forced DNS,AP Isolation,2VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 61264 Gateway/DNSCryptv2,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 60791 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Dynalink DL-WRX36-DDWRT 60791
Broadcom
Netgear R7000 --DD-WRT 61337 Gateway/DNScrypt-proxy2/AD-Block,IPset Firewall,Forced DNS,x4VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Fri Jan 31, 2025 21:27; edited 1 time in total
Joined: 16 Nov 2015 Posts: 6839 Location: UK, London, just across the river..
Posted: Fri Jan 31, 2025 21:29 Post subject:
kernel-panic69 wrote:
So, if it's broken, need screenshots and logs with firewall logging enabled and output of all the usual suspects, please
hmmm.. this needs time...and effort.. and commitment, i just dont have the first one...time
will c what i can do.. _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 58184 WAP
TP-Link WR1043NDv2 -DD-WRT 61264 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 61264 Gateway/DoT,Forced DNS,AP Isolation,2VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 61264 Gateway/DNSCryptv2,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 60791 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Dynalink DL-WRX36-DDWRT 60791
Broadcom
Netgear R7000 --DD-WRT 61337 Gateway/DNScrypt-proxy2/AD-Block,IPset Firewall,Forced DNS,x4VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Posted: Fri Jan 31, 2025 23:13 Post subject: Access Restrictions
Have done nothing, cause it worked on this Version (03_26-10-2022-r50671_netgear_r6700v3) without any issues.
Previously i've redone the complete configuration from the scratch of another issue, OpenVPN "could not determine ip4/ip6 protocol" in the past with a VPN provider, the Solution was to put the NTP TimeServer not by FQDN/DNS Hostname, needed on Startup the plain IP to work. Hard to find the solution
Anyway, i also tried to "block" the standard Services (http(s), ftp, ntp, pop, smtp, tor...) as you had, no effect....
uuuuuuuuhm yo -> hmmm.. this needs time...and effort.. and commitment, i just dont have the first one...time
And yesterday Interface Any switched to LAN, no effect...
Screenshot 2025-02-01 at 00-05-44 SafeZone (build 59397) - Access Restrictions.png
