[kernel-panic69]

@dpp3530: Thanks for secondary confirmation of non-issue.
Still waiting on @KACTET to confirm THIS issue or debunk it.
I would venture to guess that it's not an issue, other than cache
or using add-ons which has already been discussed ad nauseum.
So has co-mingling Internet traffic with surfing the webUI.

[KACTET]

You are right @kernel-panic69.
I have no problems. In additional interface options, the interface is displayed correctly, as elsewhere. Tested in two browsers: Cent Browser and Google Chrome.

[kernel-panic69]

Thanks for the confirmation, another invalid ticket closed. I was about to reply to myself after remoting into my 940 v3 after flashing that specific version and seeing no issue.

[lexridge]

Router/Version: Linksys EA8500 x2
File/Kernel: dd-wrt-webupgrade-ea8500-r58283.bin
Previous/Reset: dd-wrt-webupgrade-ea8500-r58207.bin / No reset
Mode/Status: WDS Stations to extend 1 VLAN each
Issues/Errors: Working Well

Router/Version: Linksys EA8500
File/Kernel: dd-wrt-webupgrade-ea8500-r58283.bin / No reset
Previous/Reset: dd-wrt-webupgrade-ea8500-r58207.bin / No reset
Mode/Status: Main Gateway, NSS-ECM, 5ghz WAP/VAP, VLANS w/trunking w/DHCP servers, Entware
Issues/Errors: CPU at 5% w/NSS-ECM. All good

Router/Version: Linksy R7800
File/Kernel: dd-wrt-webupgrade-r7800-r58283.bin
Previous/Reset: dd-wrt-webupgrade-R7800_r58163.bin / No reset
Mode/Status: WAP/VAP, multiple VLANs over trunk port, Entware
Issues/Errors: No issues so far and no issues with LAN ports

Router/Version: Linksys MR7350
File/Kernel: dd-wrt-webflash-mr7350-r58283.bin
Previous/Reset: dd-wrt-webflash-mr7350-r58163.bin / Many Resets
Mode/Status: Testing unit, Entware on aarch64, VLANs, WAP AX Only 5ghz
Issues/Errors: Working very well and stable

Router/Version: Linksys MX4300
File/Kernel: dd-wrt-webflash-mr7350-r58283.bin
Previous/Reset: dd-wrt-webflash-mx4300-r58163.bin
Mode/Status: Testing unit, Entware on aarch64, VLANs, WAP N/G 2.4 and AX/AC/N 5ghz
Issues/Errors: Working very well and stable with a few exceptions (See below).

MX4300: The wireless power seems to drop automatically on wlan1/2.
5ghz from 28dBm to 20dBm (radio set to 30dBm)
2.4ghz from 27dBm to 17dBm (radio set to 36dBm)
A reboot fixes it until it happens again. Usually once per day..or two. I had replaced my R7800 with this MX4300 but with the power issues, the R7800 is back in service for now.

[jrscs]

Router/Version: Netgear XR500 Nighthawk Pro Gaming (Install guide by egc)
Firmware: DD-WRT v3.0-r58283 std (09/02/24)
Kernel: Linux 6.1.107-rt28 #472 SMP PREEMPT Sun Sep 1 14:30:36 +07 2024 arm
Previous: DD-WRT v3.0-r58244 std (08/30/24)
Update Method: SSH / CLI using PuTTY with ‘firmware.bin’ install
Mode/Status: Gateway / Ok
Reset: No
Setup:
2.4 GHz N/G Mixed 20 MHz WPA2 - Vanilla, 2.4 GHz guest (VAP) WPA2
5.0 GHz AC/N Mixed 80 MHz WPA2 - Vanilla
IPv4, DHCP, DNSMasq, Static Leases, Port Forwarding
USB 3.2 Gen 1 (USB 3.0) Seagate One Touch 2TB STKB2000400 (exFAT), NAS, Samba (Restricted User/Password)
NTP Client, Wireguard Server, Wake-on-WAN (Internet), SSH (public key)
SFE Disable, QoS Disable
Issues/Errors: None, OK

[nyddwrtuser330]

R9000
previous 57793
no reset
Services: WDS AP (5GHz), 2.4 AP, SMB, INadyn, Dnsmasq, DHCP

Status: I can confirm that WIFI status lights for 2.4 and 5GHz, no longer function and permanently off as previously reported. However the WIFI is up and performing well. WDS STA connected as well as endpoints on both 2.4 and 5.

Performance seems good, so aside for lights all ok.

[Puppetnation]

Netgear Nighthawk X10 R9000

Router Wi-Fi lights still not working, both 2.4 GHz and 5 GHz.

Due to my need of wifi activity leds I switched back to r57753 (08/04/24)
which is the last build with working wifi leds.

cheers

[ramblin]

Is it just me or is wireless speed off again ? Lan connections are where they should be but wireless is pathetic. The weak little C7 wont`t play YouTube without buffering. My wireless settings mirror whats been recommended. Haven`t heard any complaints from anyone else.

[wolframium]

Router/Version: r7800
File/Kernel: webupgrade-r58283.bin
Previous/Reset: cant remember, maybe a month - have not reset in ~6months
Mode/Status: gateway
Issues/Errors: best release for me in awhile

2.4 and 5 lights working fine for me

NSS-ECM-SFE on and no issues

[Alozaros]

[bushant]

Netgear R7500v2 WDS STA
DD-WRT v3.0-r58283 std (09/02/24)
Linux 6.1.107-rt28 #472 SMP PREEMPT Sun Sep 1 14:30:36 +07 2024 arm

CLI update
No reset


wlan0 WDS Sta Vanilla w/wlan0 VAP & wlan1 AP Vanilla,
Dnsmasq, SMB, ProFTPD, Fat32 & ext2

Does not connect to R7800 58283 WDS AP when VAP is enabled

[neosimago]

Router/Version: Linksys EA8500
File/Kernel: DD-WRT v3.0-r58283 std (09/02/24) / Linux 6.1.107-rt28 #472 SMP PREEMPT Sun Sep 1 14:30:36 +07 2024 arm
Previous/Reset: DD-WRT v3.0-r53562 std (10/03/23) / No-Reset Webupdate
Mode/Status: Fiber 1Gb Gateway, SFE, with Qos / Uptime still too soon to tell.
Issues/Errors:
Noticed ssh login with Authorized keys not working; Password required.
And by changing keys to ED25519, ssh works. <-- New change since my last update.
This popped up with Samba: Would not let me access exFAT volumes; Moved data to ext4 and shares are buggy; won't share / from drive, may work if i move data to a directory. Shared my data under /opt because it won't let me reliably mount partition to locations, and share with priviliges.
Tried formatting a volume with mkfs.ext4 came with this error: Error loading shared library libblkid.so.0: No such file or directory (needed by /sbin/mkfs.ext4)
Should be noticable under System Info the load is showing ~50% but htop reflects differently. ..when using NSS-SFE; can't say it's much better than just SFE with similar results.
Speedtest results give 460/460 on lan on 1gb Frontier with NSS-SFE.
Major update for me, since i have a handful mesh working together as a local redundant lan. R53562 was very stable, trying this rollout out for the v6 kernel on one AP first. Best of luck team.

[kernel-panic69]

If your ssh keys aren't ED25519 algorithm, they won't work.

EDIT: @bushant, need exact configuration steps to reproduce the issue

[hebeda]

Router/Version: Linksys MR8300
File/Kernel: factory-to-ddwrt
Previous/Reset: stock firmware
Mode/Status:
Issues/Errors: GUI no accessable by ethernet connection, after one change has been made - still accessable over wifi , no lights

[Harb1]

Netgear wndr4300 Up and running for more than 24 hours seems like a very good build with sfe on thanks again devs. First time using this unit but the wifi lights are going on and off but wifi stays on.