Posted: Sat May 10, 2025 7:24 Post subject: [BUILD PULLED] New Build - 05/10/2025 - r61179
Welcome to Atheros r61179 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 16 Nov 2015 Posts: 6866 Location: UK, London, just across the river..
Posted: Sat May 10, 2025 8:27 Post subject:
x2 Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r61179 std (05/10/25)
Kernel Version Linux 6.1.137-rt28 #574 SMP Thu May 8 14:56:23 +07 2025 armv7l
update: CLI r60121 and 60791> r61179
reset: NO
mode: Gateway/DNScrypt-proxy v2 via Entware, AD-Block (via DNSmasq script and DNScrypt-proxy),IPset Firewall,Forced DNS,AP&Net Isolation,x2VLAN,VPN client(PBR),40 HT 2.4Ghz only(Vanilla), Disable 121
status: Operational 1h+
errors: In order to get WAN and have a separate lan ports on their own subnet and dhcpd (bridged) (tagged) SFE: ECM-NSS must be turned off ...
Im testing IPset to see if it works as intended..
Thanks BS and Team ! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 58184 WAP
TP-Link WR1043NDv2 -DD-WRT 61745 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 61745 Gateway/DoT,Forced DNS,AP Isolation,2VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 61745 Gateway/DNSCryptv2,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 61711 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Dynalink DL-WRX36-DDWRT 61745
Broadcom
Netgear R7000 --DD-WRT 61745 Gateway/DNScrypt-proxy2/AD-Block,IPset Firewall,Forced DNS,x4VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
of course all other platforms benefit from the work i'm doing on it. consider also to read about the new way vlan filtering works which i implemented as option for dsa supported routers. its different from the current vlan behaviour but makes use of the hw acceleration of the build in switches. documentation will follow up _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Posted: Sat May 10, 2025 10:43 Post subject: Linksys MR7350
Update method: WebUpgrade
Router/Version: Linksys MR7350
File: 61179
Previous/Reset: 60791 / no
Mode/Status: Gateway / ok
Issues/Errors: If you are seeing this post, all is ok
Thank you again BS and friends.
��
I had trouble with (couldnt connect to internet, but could connect to router by LAN) with
61025
60942
60832
No router settings have been changed by me between 60791 and 61179
Joined: 05 Oct 2008 Posts: 793 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Sat May 10, 2025 10:49 Post subject:
Alozaros wrote:
x2 Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r61179 std (05/10/25)
Kernel Version Linux 6.1.137-rt28 #574 SMP Thu May 8 14:56:23 +07 2025 armv7l
update: CLI r60121 and 60791> r61179
reset: NO
mode: Gateway/DNScrypt-proxy v2 via Entware, AD-Block (via DNSmasq script and DNScrypt-proxy),IPset Firewall,Forced DNS,AP&Net Isolation,x2VLAN,VPN client(PBR),40 HT 2.4Ghz only(Vanilla), Disable 121
status: Operational 1h+
errors: In order to get WAN and have a separate lan ports on their own subnet and dhcpd (bridged) (tagged) SFE: ECM-NSS must be turned off ...
Im testing IPset to see if it works as intended..
Thanks BS and Team !
I am eagerly looking forward to your test results, @Alozaros. My R7800 is still on build 60771, so I am falling behind. Until now every newer build resulted in a loss of WAN.
From what you described in the above, we have similarities in the setup of our R7800's, so I could benefit a lot from what you are able to find out.
I have port #4 on a bridge brV30 with a separate network for 4 special servers. Later I want to add a wireless VAP to this same network like I had at one time before (there's just 4 ports on the PoE switch connected to lan port #4 available).
I recently tagged both wan and lan port #4 with tag #30. It didn't make any obvious difference, but then I cannot see everything that is happening on my network, because I can only check what I know how to check ...
I have firewall rules to access the separate network on port #4 for administration from my workstation on the main network. I checked isolation of separate networks as best as I could.
There are also two VAP's for IoT and guests with their own dhcp server as well. They work. The IoT devices are just 6 smart switches with some hard wired addresses (DNA/NTP .. not 100% sure/checked). I real life there are no guests on this home network, ever
I works as intended on build 60771 despite the switch GUI being gone, but beyond that ... In Networking under bridging on the newer builds I got pull-down lists with 'filtering' and more choices which put me totally out of my depth.
I had NSS-ECM enabled, but switched it off now per your advice, to be on the ready.
Unfortunately I am not very good at describing this setup concisely because of a lack of jargon & most of all understanding ...
This whole setup of mine has been built and improved upon over a long, long time, but now it's like there's a sinkhole in the road ...
Joined: 06 Jun 2006 Posts: 7722 Location: Dresden, Germany
Posted: Sat May 10, 2025 10:49 Post subject:
we discovered a problem with pppd. i fixed that already in my tree. i hope i can push a new build tomorrow. does this fit to your problem
edit: i will remove the build now. its too important. i will do a new one tomorrow
people with access to my internal ftp will see it earlier
its fixed in r61198. small change, but big issue _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7722 Location: Dresden, Germany
Posted: Sat May 10, 2025 11:59 Post subject:
for the vlans. you need to check the new options in networking page. its all a little bit different now. its based in linux bridge filtering now which allows to make use of the hw acceleration of the switch itself. so you dont need to configure the switch anymore. each switch port has now become a own interface which can be configured by your wish. just make sure to understand how vlan filtering works since now the main bridge (or any other you create became the switch).
you can still of course create vlans per port on lan1 or lan2. but for full potential its better to use the new vlan filter capabilities. _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Oh this is good news PPP is borked on my x86 in builds after 28th of april too. If it werent for your post I'd bit the bullet and test with older asus/linksys/netgear devices of mine.
Soooo I'll lean back and wont touch a cable, awaiting the next build
Also regarding the new Switch subforum:
Will look into the devices listed there, since I want to upgrade my Network in the next few months. Maybe one of them suits my needs? Will report if so!
Joined: 06 Jun 2006 Posts: 7722 Location: Dresden, Germany
Posted: Sat May 10, 2025 13:11 Post subject:
Zyxx wrote:
Oh this is good news PPP is borked on my x86 in builds after 28th of april too. If it werent for your post I'd bit the bullet and test with older asus/linksys/netgear devices of mine.
Soooo I'll lean back and wont touch a cable, awaiting the next build
Also regarding the new Switch subforum:
Will look into the devices listed there, since I want to upgrade my Network in the next few months. Maybe one of them suits my needs? Will report if so!
Ty @Brainslayer !
consider i just tested it on a zyxel gs-1900-48 so far. all these platforms are similar and most of them have serial connectors which is good for playing. so if you get it flashed it will work. i just cannot check all these devices yet for flashing procedure. so make sure you know what you are doing. so i dont expect big problems if there are any. just initial installation can cause questions since i was first working on these devices 3 years ago and i cannot remember all the tasks. but it wasnt complicated _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
PPP is borked on my x86 in builds after 28th of april too. If it werent for your post I'd bit the bullet and test with older asus/linksys/netgear devices of mine.