Joined: 25 Jun 2014 Posts: 142 Location: São Paulo - Brazil
Posted: Wed Aug 16, 2023 22:36 Post subject: Syslog Messages
Hello there, sorry, i don't understand very well Syslog, are all this messages ok ? all yellow color. This is on TP-Link Archer C7 V4 (Latest dd-wrt release). I Have enabled Syslogd and Klogd, i have another TP-Link TL-WR841ND V9 and Syslog doesn't show all this messages.
Thank you.
Code:
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 0.000000] Zone ranges:
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 0.000000] Normal [mem 0x00000000-0x07ffffff]
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 0.000000] Movable zone start for each node
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 0.000000] Early memory node ranges
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 10.090000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 10.100000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 10.110000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 10.440000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
Dec 31 21:00:13 archerc7-v4 kern.warn kernel: [ 10.490000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Dec 31 21:00:18 archerc7-v4 kern.warn kernel: [ 18.430000] ath10k_pci 0000:00:00.0: cannot restart a device that hasn't been started
Dec 31 21:00:18 archerc7-v4 kern.warn kernel: [ 18.440000] ath10k_pci 0000:00:00.0: write_file_turboqam->failed to update channel list: -143
Dec 31 21:00:19 archerc7-v4 kern.warn kernel: [ 19.430000] ath10k_pci 0000:00:00.0: otp stream is empty, using board.bin contents
Dec 31 21:00:20 archerc7-v4 kern.warn kernel: [ 20.650000] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Dec 31 21:00:20 archerc7-v4 kern.warn kernel: [ 20.690000] ath10k_pci 0000:00:00.0: failed to set vdev 0 tx encap mode: -122
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Thu Aug 17, 2023 7:27 Post subject:
lots of those are normal/harmless and this is the way how the system boots...but...if any problems occur, and router behaves odd... than those may become handy... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Joined: 25 Jun 2014 Posts: 142 Location: São Paulo - Brazil
Posted: Fri Aug 18, 2023 4:47 Post subject:
Alozaros wrote:
lots of those are normal/harmless and this is the way how the system boots...but...if any problems occur, and router behaves odd... than those may become handy...
