Posted: Fri Jun 02, 2023 18:26 Post subject: New Build - 06/02/2023 - r52869
Welcome to Atheros r52869 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 03 Nov 2015 Posts: 316 Location: Florida, USA
Posted: Fri Jun 02, 2023 19:26 Post subject:
Router: Linksys ea8500 ..WDS AP
Firmware: DD-WRT v3.0-r52869 std (06/02/23)
Kernel: Linux 4.9.337 #1971 SMP Fri Jun 2 13:00:18 +07 2023 armv7l
Reset: No ...GUI upgrade from r52671
Mode: 2.4 GHz only ....Firmware type .. DD-WRT
Errors: None
Router: Linksys ea8500 ..WDS Stations ... X (2)
Firmware: DD-WRT v3.0-r52869 std (06/02/23)
Kernel: Linux 4.9.337 #1971 SMP Fri Jun 2 13:00:18 +07 2023 armv7l
Reset: No ...GUI upgrade from r52671
Mode: 2.4 GHz only ....Firmware type .. DD-WRT
Errors: None
VOIP phone didn`t come right back up but restarted it and everything is fine. THANKS BS and all mods that make this project GREAT ! _________________ ......All GOOD here... Just Handshakes and Time Stamps !......
I remembered what an oldass thang it is
Linksys WRT160NL
DD-WRT v3.0-r52869 std (06/02/23)
Linux 3.10.108-d11 #134823 Fri Jun 2 14:53:41 +06 2023 mips
GUI install over r52720 --- worky ok
EDIT:
sompin veddy wacky with 160NL channel survey
here is EA8500
Joined: 25 Dec 2020 Posts: 90 Location: Toronto - Canada
Posted: Fri Jun 02, 2023 22:01 Post subject:
Netgear R7800 Firmware Version Firmware: DD-WRT v3.0-r52869 std (06/02/23)
Kernel Version Linux 4.9.337 #1973 SMP Fri Jun 2 13:20:58 +07 2023 armv7l
Upgrade Method HTTPS via Web GUI
Previous Build/Reset r52651/NO
Up Time 30 minutes. Logs look good so far.
Configuration Type Gateway
WAN DHCP. LAN/wlan0 5Ghz vanilla VHT80+80 br0 with AP Mesh attached. Wlan0.1 Isolated AP Isolated network with FW rule(s) to wlan1 resource(s). Wlan1 2.4Ghz Vanilla 20/40 without Masquerade/NAT. Wlan1.1 Isolated AP and Isolated network. All clients with static leases x4 DHCP. MAC Filtering. Access restrictions. Ignore WAN DNS with static DNS servers, DNSMASQ, cached DNSSEC, Validate DNSSEC replies, no DNS rebind, Query DNS strict order. WPA 3 and WPA 2. Syslogd to FS on br0 LAN. Cooling fan USB attached. WAN traffic counter.
Everything functioning without issue. Thanks BS and team!
ISSUE DISCOVERED around 52671 or so.... but is happening daily with this version, though.
Everyday after an access restriction finishes, the clients do not have access to internet services. Only need to go to the access restrictions and hit apply to make the connections work again. This needs to be done daily following the blocked schedule now.
Last edited by CR_Apollo on Mon Jun 05, 2023 18:26; edited 5 times in total
Netgear WNDR3700 V4
DD-WRT v3.0-r52869 std (06/02/23)
Linux 3.18.140-d6 #173828 Fri Jun 2 17:41:02 +06 2023 mips
scp 'firmware.bin install over r52703
WAP + isolated guest net + OVPN server
all seems ok
Posted: Sat Jun 03, 2023 19:49 Post subject: Netgear R7800 r52869 std (06/02/23)
Router/Version: Netgear R7800
Firmware: DD-WRT v3.0-r52869 std (06/02/23)
Kernel: Linux 4.9.337 #1973 SMP Fri Jun 2 13:20:58 +07 2023 armv7l
File/Upload: dd-wrt-webupgrade.bin via GUI
Mode: Router
Reset: No
Previous: DD-WRT 05/27/2023 - r52720
Setup Using: Wireless 2.4 GHz, 5.0 GHz, Samba
Status: OK
Issues: Last several updates, router will not complete boot on its own, is unreachable. Have to power cycle router to reboot and it then loads and works fine including startup script. Power cycle or reboot takes 2.5 - 3 minutes. _________________ - a candle loses nothing by lighting another candle
Posted: Sun Jun 04, 2023 14:24 Post subject: Re: Netgear R7800 r52869 std (06/02/23)
computerperson wrote:
Router/Version: Netgear R7800
Firmware: DD-WRT v3.0-r52869 std (06/02/23)
Kernel: Linux 4.9.337 #1973 SMP Fri Jun 2 13:20:58 +07 2023 armv7l
File/Upload: dd-wrt-webupgrade.bin via GUI
Mode: Router
Reset: No
Previous: DD-WRT 05/27/2023 - r52720
Setup Using: Wireless 2.4 GHz, 5.0 GHz, Samba
Status: OK
Issues: Last several updates, router will not complete boot on its own, is unreachable. Have to power cycle router to reboot and it then loads and works fine including startup script. Power cycle or reboot takes 2.5 - 3 minutes.
Yes, I've been facing the same issue. After updating I have to turn power off to router and then turn it back on for it to start. As you said, started happening the past several updates.
I use Firefox and have to disable Avast before doing an update.
Update while hard-wired into router
Posted: Sun Jun 04, 2023 14:38 Post subject: Re: Netgear R7800 r52869 std (06/02/23)
nkaufman wrote:
computerperson wrote:
Router/Version: Netgear R7800
Firmware: DD-WRT v3.0-r52869 std (06/02/23)
Kernel: Linux 4.9.337 #1973 SMP Fri Jun 2 13:20:58 +07 2023 armv7l
File/Upload: dd-wrt-webupgrade.bin via GUI
Mode: Router
Reset: No
Previous: DD-WRT 05/27/2023 - r52720
Setup Using: Wireless 2.4 GHz, 5.0 GHz, Samba
Status: OK
Issues: Last several updates, router will not complete boot on its own, is unreachable. Have to power cycle router to reboot and it then loads and works fine including startup script. Power cycle or reboot takes 2.5 - 3 minutes.
Yes, I've been facing the same issue. After updating I have to turn power off to router and then turn it back on for it to start. As you said, started happening the past several updates.
I use Firefox and have to disable Avast before doing an update.
Update while hard-wired into router
I think you need to erase nvram and then re-enter your settings manually. It sounds to me like your nvram has something corrupted or incorrect. I know this is a pain to do, but I've been there before and this does solve many issues. _________________ Netgear R9000
DD-WRT v3.0-r55779 std (04/12/24)
Linux 4.9.337 #721 SMP Mon Apr 8 08:07:27 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Posted: Sun Jun 04, 2023 14:50 Post subject: Re: Netgear R7800 r52869 std (06/02/23)
MLandi wrote:
I think you need to erase nvram and then re-enter your settings manually. It sounds to me like your nvram has something corrupted or incorrect. I know this is a pain to do, but I've been there before and this does solve many issues.
I did ask about this earlier in one of the New Build posts.
Because I made changes over time to some settings, I'm not sure what's the best way to capture current settings so that I can replicate that after erasing nvram.
Also, I think a post mentioned that telnet into dd-wrt and running - 'nvram erase && reboot' does not always work. I might be mistaken but that's what I understood.
So, should I telnet, run 'nvram show' save all settings in a file.
Run 'nvram erase && reboot'
run 'nvram show' again and save in another file
Compare the 2 files using winmerge or something.
Change current settings to old settings values wherever needed
Will that work?
Joined: 16 Nov 2015 Posts: 6435 Location: UK, London, just across the river..
Posted: Sun Jun 04, 2023 16:33 Post subject:
Router Model Netgear R7800
Firmware Version Firmware: DD-WRT v3.0-r52869 std (06/02/23)
Kernel Version Linux 4.9.337 #1973 SMP Fri Jun 2 13:20:58 +07 2023 armv7l
update: CLI r52720 > r52869
reset: NO
mode: Gateway
status: Operational 12h+
errors: Nothing new, yet...all working as it should...router rebooted with no problem...!
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r52869 std (06/02/23)
Kernel Version Linux 3.18.140-d6 #173800 Fri Jun 2 16:44:40 +06 2023 mips
update: CLI r52720 > r52869
reset: NO
mode: Gateway
status: Operational 12h+
errors: Nothing new, yet... Thanks BS and Team !! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55779 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
