Posted: Mon May 15, 2023 5:14 Post subject: New Build - 05/15/2023 - r52569
Welcome to Marvell r52569 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r52569 std (05/15/23)
Kernel Version Linux 4.9.337 #3819 SMP Mon May 15 03:39:27 +07 2023 armv7l
Mon, 15 May 2023 11:05:13
Uptime 12 min
update-browser waterfox, I switched from partition two with -r52509 with reset, so far everything is working fine!
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Validate DNS Replies (DNSSEC)-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)- ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Extension Channel UU, Short GI, Short Preamble, Radio Scheduling, TX Power-30Bm ,TX Antenna Chains-1+2+3+4, RX Antenna Chains-1+2+3+4,DTIM Interval 1, Enable-WPA2 Personal-CCMP-128 (AES), Regulatory Domain Romania
a problem that I am reporting since switching from the two to one partition, I noticed that the router no longer responds to ping, only after a reset from the power button it returns to normal after the update, it does the same since switching from the original linksys software that I used until recently !
even if I used the nvram erase && reboot - reset default command the router behaved the same way, I had to press the power button! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Linksys WRT1900ACS
Firmware: DD-WRT v3.0-r52569 std (05/15/23) instead of DD-WRT v3.0-r52509 std (05/13/23)
Kernel: Linux 4.9.337 #3819 SMP Mon May 15 03:39:27 +07 2023 armv7l instead of Linux 4.9.337 #3815 SMP Sat May 13 09:24:22 +07 2023 armv7l
Upgrade via CUI without reset.
Works stable with unbound on adguard for WiFi dual channels.
Thank Brainslayer and team
P.S.
How ever, I found an error on Netgear R6250 which same upgrade from r52509 to r52569.
It works with dnsproxy on the same adguard for dual wifi stable.
The same PC connected WiFi to access canada.ca, no error on WRT1900ACS, how ever, SSL trouble denied to any connection whatever firefox113.x or Chrome113.y latest version. I guesss the dnsproxy some component is in trouble
Do you know what I don't understand if I install openwrt the router behaves normally even after switching from the original software or if I install openwrt on both partitions! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r52569 std (05/15/23)
Kernel: Linux 4.9.337 #3819 SMP Mon May 15 03:39:27 +07 2023 armv7l
Mode: Gateway, SFE enabled, Wifi disabled, Wireguard for external access, WAN to DSL Modem, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed yesterday, OK. Send 100 Pings to its LANside, everything fine. Will test this after next update on other partition, too.
With the above settings on the wifi side, I had disconnections on the TV again every 10 minutes, I will also attach a file with the logs from the router, after I made some changes, everything worked normally! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
I tried both options, it seems that the problems persist on the wifi side and even worse, disconnections and high ping! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
