Posted: Sat Apr 15, 2023 16:30 Post subject: New Build - 04/14/2023 - r52330
Welcome to Broadcom r52330 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r52330 std (04/14/23) Kernel: Linux 4.4.302-st38 #9130 SMP Fri Apr 14 13:06:29 +06 2023 armv7l Mode: Gateway, Wireless AP, Static Leases, Dnsmasq Caching. CTF & FA Enabled. NAT and QOS Off. All services off under Status>Sys-info. Reset: Nope, ran remove unused NVRAM parameters script. Previous: 04-08-2023-r52242 Status: Working so far; 5.8Ghz wireless is really slow. CPU load a little higher than usual. Still testing. wl: 14E4:4360 Overclock (STOCK): 1000,800 (Stock for now, 1200,1600 later if it actually works. RAM OC appears to be broken.) Temperatures: CPU 60.4 °C / WL0 50.5 °C / WL1 52.0 °C Base CFE: Modified Asus ASUS RT-AC68P/ASUS RT-AC68U (C0 Model CFE V1.3.0.7) Configured as a stock R7000.
Speedtest-4.jpg
Description:
Speedtest Over 5.8GHz Wireless. ISP Spec: 500 Mbps Down / 25 Mbps Up.
Filesize:
62.42 KB
Viewed:
3038 Time(s)
Logs.txt
Description:
Full system logs. MAC scrubbed, password scrubbed, the fun stuff at the bottom as usual!
Router/Version: Linksys EA6900/XAC1900 DD-WRT
File/Kernel: [url=https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2023/04-14-2023-r52330/linksys-ea6900/linksys-ea6900-webflash.bin (r52330)[/url] / Linux 4.4.302-st38 #9130 SMP Fri Apr 14 13:06:29 +06 2023 armv7l
Previous/Reset: r51140 / no
Mode/Status: 2.4ghz AP working, Android Tether not working
Error: Failure to assign IP address to USB0 and be android tether gateway after "udhcpc -i usb0" with kernel modules loaded, early step of DD-WRT Android Tether/USB Modem tutorial from wiki
Logs with mac addresses removed;
Joined: 16 Nov 2015 Posts: 6446 Location: UK, London, just across the river..
Posted: Tue Apr 18, 2023 10:01 Post subject:
@baboeska is your USB interface visible/selectable, at basic set up page or at the network set up page, where you can adjust WAN interfaces...
The thing that it is created, but not used points me to, you either have to selected it via GUI..or
use start up commands to set it as a WAN...(you may even need to do some other bits, like give it a DHCPd)
Im not really into this type of a WAN use via USB at all, there are other forum members that could help you, much better than me, i've sent you a PM that you never opened...but here is what i pointed you...
(see above mac913's updated post with R7000 5 GHz speedtest)
03-23-2023-r52095 works great and 04-08-2023-r52242 works fine as well but has a long startup time and issues with being able to capture the boot log unless I have a serial cable attached.
Some builds work awesome with my config, some do not. I primarily use Dnsmasq with caching and static leases for my config. DHCP is turned off except for on the WAN. I also use Dnscrypt. Other than that It's pretty vanilla, all other services are turned off in the GUI.
Other R7000 users show no issues, speeds are fine, so backup old config, save copy of nvram show and start over.
r52095 this is before Broadcom Switch Config received upgrades also since then wireless channel changes or fixes.
So maybe you can make enough changes to fix your existing config, but I would start over fresh this is guaranteed.
I don't recommend reusing a backup config from an older build. I would save the all the GUI configuration pages by printing to PDF; Load build 52330, then nvram erase && reboot. Now manually config the router from the PDF backup. Don't be lazy, well that is what I tell myself when I have problems with a new build. _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
