Setting up PPPoE and tagging vlan 40 on a Netgear R7000P

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Author Message
Wuvbit
DD-WRT Novice


Joined: 25 Nov 2017
Posts: 13

PostPosted: Wed Mar 29, 2023 17:37    Post subject: Setting up PPPoE and tagging vlan 40 on a Netgear R7000P Reply with quote
See comment below

Last edited by Wuvbit on Tue Apr 25, 2023 11:17; edited 1 time in total
Sponsor
ho1Aetoo
DD-WRT Guru


Joined: 19 Feb 2019
Posts: 2927
Location: Germany

PostPosted: Wed Mar 29, 2023 17:51    Post subject: Reply with quote
the following is too simple?


81111111186.png
 Description:
 Filesize:  148.74 KB
 Viewed:  1578 Time(s)

81111111186.png


Wuvbit
DD-WRT Novice


Joined: 25 Nov 2017
Posts: 13

PostPosted: Tue Apr 25, 2023 2:07    Post subject: Reply with quote
ho1Aetoo wrote:
the following is too simple?


Yes, it is too simple.

As I stated in my post...

Wuvbit wrote:

Under Setup > Switch Config:
No port was checked for VLAN 0.
Ports CPUPORT 1 2 3 4 were checked for VLAN 1.
Only CPUPORT was checked for VLAN 2.
I added VLAN 40 and I checked CPUPORT and WAN.
Under WAN I checked Tagged.

I clicked Apply Settings.

Under Setup > Networking:
eth0.40 did not appear under Interface Setup > WAN Port Assignment. So I added a line under VLAN Tagging for eth0, set the tag to 40 and priority to 0.

I clicked Apply Settings.

This caused eth0.40 to appear under WAN Port Assignment so I selected it.


It doesn't appear that your screenshot is from the same firmware as the latest firmware available for this router at the time that post was written either...
ho1Aetoo
DD-WRT Guru


Joined: 19 Feb 2019
Posts: 2927
Location: Germany

PostPosted: Tue Apr 25, 2023 5:52    Post subject: Reply with quote
You're still doing it wrong.
And if you have a CPU port to choose from in the "switch config tab" then it works exactly as shown in the screenshot.

VLAN interfaces are created automatically if the CPU port is tagged.

no other nonsense necessary

there is also no need to set "pppoe_wan_ifname" - all bullshit
we don't need bullshite instructions if you can set everything you need with 3 clicks in the GUI

and eth0.40 will also not appear for selection but VLAN40

the last firmware is available at https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2023/04-20-2023-r52369/netgear-r7000P/
Wuvbit
DD-WRT Novice


Joined: 25 Nov 2017
Posts: 13

PostPosted: Tue Apr 25, 2023 10:56    Post subject: Reply with quote
ho1Aetoo wrote:
You're still doing it wrong.
And if you have a CPU port to choose from in the "switch config tab" then it works exactly as shown in the screenshot.

VLAN interfaces are created automatically if the CPU port is tagged.

no other nonsense necessary

there is also no need to set "pppoe_wan_ifname" - all bullshit
we don't need bullshite instructions if you can set everything you need with 3 clicks in the GUI

and eth0.40 will also not appear for selection but VLAN40

the last firmware is available at https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2023/04-20-2023-r52369/netgear-r7000P/


Edit because I'm wrong


Last edited by Wuvbit on Tue Apr 25, 2023 11:15; edited 1 time in total
ho1Aetoo
DD-WRT Guru


Joined: 19 Feb 2019
Posts: 2927
Location: Germany

PostPosted: Tue Apr 25, 2023 11:04    Post subject: Reply with quote
Thanks for sharing your misconfiguration.
Your CPU port is still not tagged.

ho1Aetoo wrote:
VLAN interfaces are created automatically if the CPU port is tagged.


Rolling Eyes Rolling Eyes Rolling Eyes


And you certainly don't have to explain to me how the "switch config tab" works'.

I strongly recommend you to take over the settings I have posted 1:1 ... then everything works !!!

https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1283014#1283014
Wuvbit
DD-WRT Novice


Joined: 25 Nov 2017
Posts: 13

PostPosted: Tue Apr 25, 2023 11:16    Post subject: Reply with quote
ho1Aetoo wrote:
Thanks for sharing your misconfiguration.
Your CPU port is still not tagged.

ho1Aetoo wrote:
VLAN interfaces are created automatically if the CPU port is tagged.


Rolling Eyes Rolling Eyes Rolling Eyes


And you certainly don't have to explain to me how the "switch config tab" works'.

I strongly recommend you to take over the settings I have posted 1:1 ... then everything works !!!

https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1283014#1283014


You're right, once checked it works properly now.

Sorry.
ho1Aetoo
DD-WRT Guru


Joined: 19 Feb 2019
Posts: 2927
Location: Germany

PostPosted: Tue Apr 25, 2023 11:23    Post subject: Reply with quote
It's very simple, if a port is in more than one VLAN then it has to be tagged
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum