Posted: Tue Mar 28, 2023 13:43 Post subject: New Build - 03/28/2023 - r52189
Welcome to Marvell r52189 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r52189 std (03/28/23)
Kernel Version Linux 4.9.337 #3717 SMP Tue Mar 28 02:52:06 +07 2023 armv7l
Current Time Tue, 28 Mar 2023 17:14:52
Uptime 10 min
update-browser waterfox, I switched from partition one on the linksys firmware, all ok
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
After configuring the settings, I rebooted the router every time!
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Extension Channel LL, Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, 30TX Power-26Bm ,TX Antenna Chains-1+2+3+4, RX Antenna Chains-1+2+3+4, Enable-WPA2 Personal-CCMP-128 (AES), Regulatory Domain Romania
I want to say that this firmware is something, for the first time I see 6jitter and 10ms ping in speed test 4 in speed test on the phone, on the smart TV I am connected and everything is played without interruptions.
a negative remark would be that after switching from partition one with the linksys software, the router no longer loads its firmware with ddwrt and loses ping
thank you brainslayer and everyone involved in the development of dd-wrt!
something new for me, I don't know if it is correct? _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
I want to say that this firmware is something, for the first time I see 6jitter and 10ms ping in speed test 4 in speed test on the phone, on the smart TV I am connected and everything is played without interruptions.
update-browser waterfox, I switched from partition one on the linksys firmware, all ok a negative remark would be that after switching from partition one with the linksys software, the router no longer loads its firmware with ddwrt and loses ping
what does this mean, after a reboot I found it disabled, if i activate it I have internet only on the wifi side! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Visual artifact reboot saved r52189 build configuration but in both cases VLANs was disabled before / after reboot.
Unless you want to correctly configure and test VLANs I suggest you keep it disabled, as this has been the default.
please explain exactly what I have to do, how the command show in the command line: 1x with tab disabled and 1x with enabled.that can show us the difference. _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Joined: 21 Aug 2019 Posts: 120 Location: Here, There And Everywhere
Posted: Wed Mar 29, 2023 12:37 Post subject:
Maybe this will be of use (for WRT1200AC, which is similar to WRT1900). With VLAN on, only Wifi connection is possible. Configured as WAP, although this probably doesn't affect the outputs..
after rebooting the router, the wifi part no longer has internet, only access to the router is possible and and after unchecking Vlans, rebooting the router, everything returns to normal! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt