Posted: Sun Mar 26, 2023 14:47 Post subject: New Build - 03/26/2023 - r52148
Welcome to Broadcom r52148 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Asus RT-AC88U
File/Kernel: DD-WRT v3.0-r52148 std (03/26/23)/Linux 4.4.302-st38 #8992 SMP Sun Mar 26 04:17:24 +06 2023 armv7l
Previous/Reset: r52095/no
Mode/Status: All the functions and services I used are working fine. except hidden ESSID
Issues/Errors: Not sure if this bug has been reported, but I am using repeater mode, I made a new virtual wireless and I disabled the ESSID to make it hidden, but the ESSID still is still visible and not hidden. This was on both r52148 and r52095. BTW I didn't test any previous versions! _________________ Asus RT-AC88U Donations
Last edited by Jen1 on Thu Apr 13, 2023 18:56; edited 6 times in total
Anyone using the Switch Config VLAN GUI in the past will find after loading this build the Switch Config VLAN GUI is disabled. I re-enabled it and seen no VLANs where assigned to any ports even the WAN port from the previous build 52095 on the R7000. You will see a new CPUPORT selection too. I reassigned the my VLAN Ports and also enabled the CPUPORT to all used VLANs and also the enabled CPUPORT Tagged.
My initial mistake was I re-enabled the Switch Config VLAN which was blank and rebooted and lost access to the R7000 and had to RESET. I had a backup config from 52095.
R7000_VLAN_52148.jpg
Description:
Filesize:
69.21 KB
Viewed:
3563 Time(s)
_________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Well if you had a backup then you didn't have to reset anything.
The "switch config tab" has received a small update therefore existing VLAN configurations have been reset.
But that there were no VLANs at all sounds a bit strange?
It can be that for your specific router standard settings are missing.
I seen the VLAN GUI disabled and enabled it, then seen all the vlans were unchecked I just just Reboot thinking it would correct itself but no, I lost access to the R7000 and a RESET was required and was able to reload the last configuration save and fixed the VLAN GUI setup. All is good now. Just a WARNING to others. _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Router/Version: XAC1900 (EA6900 + XVortex CFE)
Previous/Reset: r52095/no
Mode/Status: IPv4, IPv6 HE Tunnel, mount /jffs /opt, Entware, mtd write * linux, 2.4g/5g wan, dhcpd wan client, dhcp lan server, ssh
Issues/Errors: No major problems, LAN IPv6 addresses not working except for ipv6 dns, router gets IPv6 address, probably my config.
USB still auto-mounting to /tmp/mnt/sda1 not /mnt/sda1, doesn't seem to allow command line mounting currently.
Anyone using the Switch Config VLAN GUI in the past will find after loading this build the Switch Config VLAN GUI is disabled. I re-enabled it and seen no VLANs where assigned to any ports even the WAN port from the previous build 52095 on the R7000. You will see a new CPUPORT selection too. I reassigned the my VLAN Ports and also enabled the CPUPORT to all used VLANs and also the enabled CPUPORT Tagged.
My initial mistake was I re-enabled the Switch Config VLAN which was blank and rebooted and lost access to the R7000 and had to RESET. I had a backup config from 52095.
Thanks for the heads up, I had similar issues when trying this build.
Posted: Mon Mar 27, 2023 4:27 Post subject: Netgear Nighthawk R7000
Router/Version: Firmware: Kernel: Mode: Gateway, Wireless AP, Static Leases, Dnsmasq Caching. CTF & FA Enabled. NAT and QOS Off. All services off under Status>Sys-info. Reset: Nope, ran remove unused NVRAM parameters script. Previous: 03-23-2023-r52095 Status: Working; really slow wi-fi and some other issues with Intel AX200 clients, will post logs later. wl: 14E4:4360 Overclock (STOCK): 1000,800 (Stock for now, 1200,1600 later if it actually works. RAM OC appears to be broken.) Temperatures: Base CFE: Modified Asus ASUS RT-AC68P/ASUS RT-AC68U (C0 Model CFE V1.3.0.7) Configured as a stock R7000.
Too many issues, rolling back to 03-23-2023-r52095
Speedtest.jpg
Description:
Speedtest Over 5.8GHz Wireless. ISP Spec: 500 Mbps Down / 25 Mbps Up.
Filesize:
60.7 KB
Viewed:
3248 Time(s)
Logs.txt
Description:
Full system logs. MAC scrubbed, password scrubbed.