Posted: Mon Mar 13, 2023 8:12 Post subject: New Build - 03/13/2023 - r52004
Welcome to Atheros r52004 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: R7800
File/Kernel: Linux 4.9.337 #1644 SMP Mon Mar 13 06:16:55 +07 2023 armv7l
Previous/Reset: r51958 / no
Mode/Status: Gateway / working up since 48h
Services Used: PPPoE,DHCP,DHCP-Reservation,Dnsmasq + PiHole,DDNS,SSH ed25519,WiFi 2,4Ghz + 5Ghz AP's + VAP's Vanilla,USB,Port forwarding,QoS
Issues/Errors: nothing so far
The vanilla firmware crash from build r51976 seems to be fixed
Edit: mhm, my R7800 has a bad TX power after a reboot.
if I press apply in the WLAN tab, the transmission power is normal again as set.
In addition in WebIF I see as maximum transmit power 30dB (not allowed in Germany).
Last edited by ho1Aetoo on Tue Mar 14, 2023 9:35; edited 2 times in total
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r52004 std (03/13/23)
Kernel Version Linux 3.18.140-d6 #166447 Mon Mar 13 09:34:23 +06 2023 mips
update: GUI r51976 > r52004
reset: NO
mode: Gateway
status: Operational
errors: Nothing new, yet... BS Thanks for fixing the web flash, no reboot, error 404 problem...
Now everything work accordingly...on this unit !
Will report later if anything at all...Thanks again BS ! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55779 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Errors - 5GHz Channel list is missing channels, setting changed to auto because of lack of selected 149 in list- reg domain = UNited States, this is only after initial flash. Once you select a visible channel,apply and go back the missing channels are now visisble and selectable.
Vanilla being used, Inadyn, smb, QOS, DNSMasq WDS AP (5Ghz), AP 2.4Ghz
All good after fixing channel
r7800
WDS STA (5GHz), VAP 5GHz, Ap2.4GHz
Errors - broken since 51589, the VAP on the 5GHz interface while primary in is in WDS sta mode does not operate, Radio is listed as active has correct ssid, is even able to detect proper signal power, but never assigns channel and rate is listed as auto. Firmware type does not matter. The Same interface does properly connect and create the WDS link, Just the VAP doesnt work. PAcket counters in status for int 0.1 do not increase from 0
it's broken, no client is able to even see the SSID and the channel should be assigned. No client can connect, the counters just show no client is connected. All my in range clients are connecting to the 2.4 and cant see the 5 becuase its not transmitting the vap.
the radio itself hardware wise is working because its connecting wlan0 back over wds and bridging is working cause my 2.4 GHz clients can get outbound to the WDS AP gateway on the 9K. I just cant get this VAP working. If i revert back to last working version, the vap comes right up with channel assigned and nearly every device in range connects on 5Ghz Vap, with no change to settings
@mlandi, if you were using one of the channels that didnt disapeer you were probably fine, i was using 149, that one wasnt in list. But once i saved one that was, applied, the list rebuilt and i was able to select 149 again. so it seems to be easy to fix if it happens.
Linksys EA8500...main gateway
DD-WRT v3.0-r52004 std (03/13/23)
Linux 4.9.337 #1642 SMP Mon Mar 13 05:55:32 +07 2023 armv7l
GUI install over r51935 - NO reset
all worky ok --> using VANILLA FW
Netgear WNDR3700 V4
DD-WRT v3.0-r52004 std (03/13/23)
Linux 3.18.140-d6 #166475 Mon Mar 13 10:35:19 +06 2023 mips
GUI install over r51935
WAP / guest on isolated VAP / OVPN server
all good -- its dmesg looky better
https://mrjcd.com/junk/dd-wrt/WNDR3700v4/r52004_wndr3700v4-dmesg.html