Posted: Wed Mar 08, 2023 14:47 Post subject: New Build - 03/08/2023 - r51976
Welcome to Marvell r51976 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
Note (by egc): if you use WireGuard and IPv6 better skip this build and wait for the next !
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
WRT1200ac v1 r51976 update kills my VPN connection (ExpressVPN). Revert to r51937 restores vpn connection. Everything else working as usual.
Only detected difference is the VPN connection on r51937 uses "OpenSSL 1.1.1s" while the failed r51976 vpn connection shows "OpenSSL 1.1.1t"
Seems there is a flaw in my vpn setup that won't allow connection using the "t" version using r51976. Will check with provider. Just sharing results no need to respond.
Joined: 12 Dec 2007 Posts: 764 Location: Pittsburgh, PA USA
Posted: Thu Mar 09, 2023 1:48 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r51976 std (03/08/23)
Previous/Reset: DD-WRT v3.0-r51937 std (03/05/23), Full reset and reconfigure.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS/DNSMasq, OpenVPN server, Wireguard Server
Issues/Errors:
After upgrade, could not ping internet IP addresses from clients (wired or wireless). Did a full reset and reconfigure. Issue seems to be with the Tunnels tab, specifically my Wireguard server. Once I configure my server, I can't get out. If I disable the tunnel and reboot, it works again. Rolled back to r51937. _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
DD-WRT Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r51976 std (03/08/23)
Kernel Version Linux 4.9.337 #3681 SMP Wed Mar 8 07:44:08 +07 2023 armv7l
Current Time Thu, 09 Mar 2023 23:17:32
Uptime 12:34
update-browser waterfox, I switched from partition 1 Linksys Firmware, all ok
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Validate DNS Replies (DNSSEC)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
After configuring the settings, I rebooted the router every time!
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-48,Extension Channel LL, Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, 30TX Power-30dBm ,TX Antenna Chains-1, RX Antenna Chains-1, Enable-WPA2/WPA3 Personal-CCMP-128 (AES), Regulatory Domain Romania, all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,TurboQAM (QAM256) On, Short Preamble, Short GI, Radio Scheduling,TX Power-30dBm ,TX Antenna Chains-1, RX Antenna Chains-1 Enable-WPA2/WPA3 Personal-CCMP-128 (AES) all-ok! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
PPPoE iPv6 Type DHCPv6 with Prefix Delegation, Prefix Length 64 bit loses ipv6 on the wifi side, if I set it to 56 it doesn't lose anymore, has anyone encountered this problem, only on the wifi side!? _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
for those who want to try these settings _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Router/Version: Linksys WRT3200 File/Kernel: v3.0-r51976 Previous/Reset: v3.0-r51937 Mode/Status: Router Issues/Errors: with this version there are again extremely many disconnections. It's most obvious on a Samsung S10+, which is about as vulnerable as all iPhones