My phone was refusing to connect to the 2.4ghz WIFI, it would try to connect, then drop and retry, non stop..
So I tinkered around with some of the settings to see if I could make it stable (tried turning off TurboQAM, for example, as I read that somewhere), but now it refuses to come up properly, and does not show on the phone under available WIFIs.
The Wireless Status pages does not seem to report healthy numbers either:
Nothing untoward in the log as far as I can see.
I even tried restoring a config file from earlier this evening, before it disappeared and still not coming up..
I do not think the current firmware is to blame, because I reverted back to r50146 and it was happening there as well. (It might well have been going on for a while, as I only use 5ghz on my phone/laptop, so might not have realised)
If there is anything I can provide that might be useful please let me know.
Unless you're in a *really* congested area for 2.4 band, use channel 1, 6, or 11. Looks as if the old presumptions were correct, the old default for ack timing of 2000 is actually 2250. All you really need at most is 900 or 1350, but you can test 450 and 1800 as well. _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
Thanks for the feedback.. I have made the recommended changes, but the WIFI AP is still not showing up on my phone, nor does the status page look healthy to me:
For example, my selected channel (1) shows as "Unknown"? TX Power as 0 dbm.
Joined: 16 Nov 2015 Posts: 6446 Location: UK, London, just across the river..
Posted: Sun Mar 05, 2023 9:20 Post subject:
im sorry but on R7800 wlan1 is the 5Ghz radio..and you are showing it off..
2,4Ghz is wlan0 ...
If your router behaves funny try to reset the router and manually enter all the settings accordingly..do not load save files from an old or different builds...
There is a sticky on the top of the Atheros forum https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324014
Read it carefully and try those recommended settings...also use vanilla but not DDWRT firmware..
for example my r7800 is rock solid with its current wifi set up... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
im sorry but on R7800 wlan1 is the 5Ghz radio..and you are showing it off..
2,4Ghz is wlan0 ...
Thats not the case on my router:
Alozaros wrote:
If your router behaves funny try to reset the router and manually enter all the settings accordingly..do not load save files from an old or different builds...
There is a sticky on the top of the Atheros forum https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324014
Yes I fully understand, however with people in the house that dont appreciate having downtime its tempting to just upgrade the firmware with no reset.
Im in the process of documenting all the config on my router now, so if I get a chance I will do a reset and re-configure the things that I have set up.
Joined: 16 Nov 2015 Posts: 6446 Location: UK, London, just across the river..
Posted: Sun Mar 05, 2023 11:03 Post subject:
..."this is not true on the r7800 wlan0 has always been the 5ghz interface "...
correct my mistake ...
scope2 wrote:
Im in the process of documenting all the config on my router now, so if I get a chance I will do a reset and re-configure the things that I have set up.
to make is easier... export those router pages to PDF or print to PDF than copy paste the values most of the modern browsers support than PDF thing.. _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913