Posted: Sat Feb 25, 2023 11:29 Post subject: New Build - 02/25/2023 - r51855
Welcome to Marvell r51855 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
DD-WRT Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r51855 std (02/25/23) Kernel Version Linux 4.9.337 #3653 SMP Sat Feb 25 04:33:27 +07 2023 armv7l
Current Time Sun, 26 Feb 2023 20:50:27
Uptime 6:58
update-browser waterfox, I switched from partition 1 Linksys Firmware, all ok
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Validate DNS Replies (DNSSEC)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
After configuring the settings, I rebooted the router every time!
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, Enable-WPA2/WPA3 Personal-CCMP-128 (AES), Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI, Radio Scheduling, Enable-WPA2/WPA3 Personal-CCMP-128 (AES) all-ok!
I have noticed this thing for a long time if the MTU is set to AUTO after saving the settings, it switches to manual, this is normal? _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
I am running r51741 on my WRT3200ACM and I have not been able to get port forwarding to work. Any suggestions how to fix this or does this new beta fix that ptoblem? Thank you.
Manually reconfigure after hardware reset (button 10 seconds), webUI Factory Defaults or nvram erase && reboot.
Current build r51855 or later is always good idea. Upgrade before reset. Do not expect new builds to fix the issue.
If your router is connected to another gateway this is a situation of double NAT so it is outside of DD-WRT control.
Config the ISP equipment port forward or reconfigure to true bridge mode or at least IP passthrough or DMZ plus.
Joined: 12 Dec 2007 Posts: 783 Location: Pittsburgh, PA USA
Posted: Mon Feb 27, 2023 22:30 Post subject:
Router/Version: WRT1900AC v1
File/Kernel: DD-WRT v3.0-r51855 std (02/25/23)
Previous/Reset: DD-WRT v3.0-r51838 std (02/23/23), No reset this time.
Mode/Status: Gateway (SFE enabled), Access Point, IPV6 (DHCP6 w/ prefix delegation), Entware, DOT via SmartDNS, OpenVPN server, Wireguard Server
Issues/Errors:
Up 24 hours, nperf.com shows expected ISP speeds, both wired and wireless. OpenVPN, Wireguard, and DOT, all working as expected. I had to make an MTU change (from 1500 to 1400) in OpenVPN but that's due to my cell phone carrier (T-Mobile). I previously made a similar change in Wireguard.
