Posted: Sat Feb 18, 2023 6:33 Post subject: New Build - 02/18/2023 - r51741
Welcome to Marvell r51741 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp). 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
DD-WRT Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r51741 std (02/18/23) Kernel Version Linux 4.9.337 #3641 SMP Sat Feb 18 06:19:05 +07 2023 armv7l
Current Time Sat, 18 Feb 2023 09:13:16
Uptime 8 min
update-browser waterfox, I switched from partition 1, Firmware Version v3.0-r51729, all ok
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Validate DNS Replies (DNSSEC)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC/N, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, Enable-WPA2/WPA3 Personal-CCMP-128 (AES), Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,TurboQAM (QAM256),Short Preamble, Short GI ,Threshold 784, Radio Scheduling, Enable-WPA2/WPA3 Personal-CCMP-128 (AES) all-ok!
After configuring the settings, I rebooted the router every time! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
- update works good without any problems
- VPN WireGuard
- USB
- DDNS
- cron
- Port Forwarding
- FTP
- Samba
- WLAN offline, I use UniFi AP AC LITE as access Point!
- Lan
in the last Verion that i have installed (r49677) the "cron" Tab/Line does not work correct.
I will check the "cron" function in this version and report when its ok.
This works perfect before Version r49677:
10 0 * * 5 root find /tmp/mnt/sda1/Cam1/ -type d -name "20*" -mtime +26 -print0 | xargs -0 rm -r
This works perfect before Version r49677:
10 0 * * 5 root find /tmp/mnt/sda1/Cam1/ -type d -name "20*" -mtime +26 -print0 | xargs -0 rm -r
Have you considered saving the command as a USB script and calling the script from cron instead? _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
hello,
this cron jobs (see Picture) work perfect in the past with older version before r49677.
I will try this new Version, after test I will report the result.
Posted: Sun Feb 19, 2023 8:46 Post subject: Turbo QAN kills 2.4ghz wifi - was reported
Upgraded from 51306 to 51741 today on Linksys wrt1900acs v2.
I carried forward all existing settings. Those settings included "TurboQAM (QAM256)" enabled on the 2.4 Ghz wifi, which is set to run at "N only".
The 2.4Ghz network, did not come up for users, and was not broadcasting an SSID. Other testing so far, has shown everything else running - same as before.
This same issue was first reported in r51506 on 25 Jan by @raywan:
raywan wrote: When TurboQAM is enable in 2.4GHz, all of my android devices and Rpi cannot be connected and shown as channel unknown in router status page. No 2.4Ghz SSID is shown on all of my android devices. The only one way is disable TurboQAM and reboot the router then 2.4Ghz SSID is coming back again without any problem. I am doubt the TurboQAM is able to function well in previous version since the 2.4GHz connection is only 2~3MB/s with good quality signal. Rollback to 01-19-2023-r51440
The workaround is to either: disable "TurboQAM" in Wireless-> Basic Settings. OR rollback to a version before r51506
Posted: Sun Feb 19, 2023 15:04 Post subject: Re: Turbo QAN kills 2.4ghz wifi - was reported
shb wrote:
Upgraded from 51306 to 51741 today on Linksys wrt1900acs v2.
I carried forward all existing settings. Those settings included "TurboQAM (QAM256)" enabled on the 2.4 Ghz wifi, which is set to run at "N only".
The 2.4Ghz network, did not come up for users, and was not broadcasting an SSID. Other testing so far, has shown everything else running - same as before.
This same issue was first reported in r51506 on 25 Jan by @raywan:
raywan wrote: When TurboQAM is enable in 2.4GHz, all of my android devices and Rpi cannot be connected and shown as channel unknown in router status page. No 2.4Ghz SSID is shown on all of my android devices. The only one way is disable TurboQAM and reboot the router then 2.4Ghz SSID is coming back again without any problem. I am doubt the TurboQAM is able to function well in previous version since the 2.4GHz connection is only 2~3MB/s with good quality signal. Rollback to 01-19-2023-r51440
The workaround is to either: disable "TurboQAM" in Wireless-> Basic Settings. OR rollback to a version before r51506
Try these settings and restart, I do not recommend TurboQAM (QAM256) it is not stable with it, I also noticed some instability in this version on the wifi side, and I managed to find a balance with these settings! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
I actually stayed on 51741. Partly because I am so diabolically busy at the moment. So it was just easier, and less time consuming, to simply disable the TurboQAM, get the 2.4 wifi up again.... and not have to think about it.
If there do prove to be performance problems with the 2.4 on this release, compared with r51306, I will think about rolling back or not rolling back sometime over the next week. So far, I have not investigated, and nobody has complained about it... so I am hoping to stay with this one.
I do not use the 2.4Ghz wifi myself with any of the my personal devices. So unless I actively investigate, or someone complains, a rollback is unlikely.
UPDATE - ah - got it now there was a delayed reaction. Those screenshots did not come through immediately with your post. I have them now. Thanks! But probably won't look at the details for a least a few days. Unless someone here complains...
- update works good without any problems
- VPN WireGuard
- USB
- DDNS
- cron
- Port Forwarding
- FTP
- Samba
- WLAN offline, I use UniFi AP AC LITE as access Point!
- Lan
in the last Verion that i have installed (r49677) the "cron" Tab/Line does not work correct.
I will check the "cron" function in this version and report when its ok.
This works perfect before Version r49677:
10 0 * * 5 root find /tmp/mnt/sda1/Cam1/ -type d -name "20*" -mtime +26 -print0 | xargs -0 rm -r
- update works good without any problems
- VPN WireGuard
- USB
- DDNS
- cron
- Port Forwarding
- FTP
- Samba
- WLAN offline, I use UniFi AP AC LITE as access Point!
- Lan
in the last Verion that i have installed (r49677) the "cron" Tab/Line does not work correct.
I will check the "cron" function in this version and report when its ok.
This works perfect before Version r49677:
10 0 * * 5 root find /tmp/mnt/sda1/Cam1/ -type d -name "20*" -mtime +26 -print0 | xargs -0 rm -r
best regards, and thank you!!
the cron job also does not work in this version
What is going wrong???
-------------------------------------------------------