Posted: Wed Jan 25, 2023 9:23 Post subject: New Build - 01/25/2023 - r51506
Welcome to Marvell r51506 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
DD-WRT Router Model Linksys WRT1900ACS v2
Firmware Version DD-WRT v3.0-r51506 std (01/25/23)
Kernel Version Linux 4.9.337 #3607 SMP Wed Jan 25 02:20:36 +07 2023 armv7l
Uptime 11 min
update-browser waterfox, I switched from partition 1 from Linksys firmware, all ok
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Validate DNS Replies (DNSSEC)-ok
Port Forwarding - Ok,
USB - System Log -Ok
Schedule Reboot - At a Set Time - On
Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC/N, Width VHT 80 Mhz-Wireless Channel-36,Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, Enable-WPA2/WPA3 Personal-CCMP-128 (AES, Regulatory Domain Romania , all-ok
Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-6, Extension Channel Lower,Short Preamble, Short GI , Radio Scheduling, Enable-WPA2/WPA3 Personal-CCMP-128 (AES) all-ok!
After configuring the settings, I rebooted the router every time! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Router/Version: Linksys WRT32X File/Kernel: DD-WRT v3.0-r51440 std (01/19/23) Linux 4.9.337 #3603 SMP Thu Jan 19 04:28:37 +07 2023 armv7l Previous/Reset: Linux 4.9.337 #3603 SMP Thu Jan 19 04:28:37 +07 2023 armv7l Mode/Status: AP Mode Issues/Errors: 2.4Ghz SSID disappear when TurboQAM is enable
When TurboQAM is enable in 2.4GHz, all of my android devices and Rpi cannot be connected and shown as channel unknown in router status page. No 2.4Ghz SSID is shown on all of my android devices. The only one way is disable TurboQAM and reboot the router then 2.4Ghz SSID is coming back again without any problem. I am doubt the TurboQAM is able to function well in previous version since the 2.4GHz connection is only 2~3MB/s with good quality signal. Rollback to 01-19-2023-r51440
Router/Version: Linksys WRT32X File/Kernel: DD-WRT v3.0-r51440 std (01/19/23) Linux 4.9.337 #3603 SMP Thu Jan 19 04:28:37 +07 2023 armv7l Previous/Reset: Linux 4.9.337 #3603 SMP Thu Jan 19 04:28:37 +07 2023 armv7l Mode/Status: AP Mode Issues/Errors: 2.4Ghz SSID disappear when TurboQAM is enable
When TurboQAM is enable in 2.4GHz, all of my android devices and Rpi cannot be connected and shown as channel unknown in router status page. No 2.4Ghz SSID is shown on all of my android devices. The only one way is disable TurboQAM and reboot the router then 2.4Ghz SSID is coming back again without any problem. I am doubt the TurboQAM is able to function well in previous version since the 2.4GHz connection is only 2~3MB/s with good quality signal. Rollback to 01-19-2023-r51440
I also activated TurboQAM, wifi 2.4Ghz is visible, but I noticed a 30% decrease in speed in the speed test compared to not having it active, I recommend you not to use it on wrt1900acs v2, although my settings everything works perfectly! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Router/Version: Linksys WRT1900ACS v2
File: ddwrt-linksys-wrt1900acsv2-webflash.bin
Firmware: DD-WRT v3.0-r51506 std (01/25/23)
Kernel: Linux 4.9.337 #3607 SMP Wed Jan 25 02:20:36 +07 2023 armv7l
Mode: Gateway, SFE enabled, Wifi disabled, Wireguard for external access, WAN to DSL Modem, samba to access USB3-ext4 SSD, Keep Alive reboot 5:00 in the morning
Reset: No
Status: Installed yesterday, OK.
Load average 0.00, 0.00, 0.00, Temperatures CPU 65.5 °C / WL0 39.2 °C / WL1 40.6 °C
Regarding above mentioned turboQUAM:
Keep in mind not only the Router, but also the devices have to support this.
TurboQUAM is a nice feature, but it often results in reduced throughput for devices that can not handle it proper.
RTS Threshold Enable @ 784 it seems that helps TurboQUAM in 2.4Ghz, following the comments I tried to test in different settings, try and come back with opinions....
I created a Virtual Interfaces Guest network and unchecked access to Web UI Access, I logged in from my phone to this guest network and I still have access to the Web UI interface!
Normally I should not have access to the Ui web interface on the router? _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
Does the setting work for the main WLAN interfaces?
As I said, everything works here.
May not help you but if you want to configure a guest WLAN you should create unbridged VAPs.
an unbridged VAP has its own subnet and can be completely isolated from other subnets.
E.g. you can activate the switch "network isolation" which isolates the VAP against the complete main LAN including WebIF.
and for the normal network it behaves the same way _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
if I switch to Unbridged I have no internet _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
please read the stickies and instructions in the forum
the unbridged VAP of course can not have the same IP address as the router but must have its own subnet e.g.
192.168.234.1/24 and it also needs its own DHCP server